Reely 1611426 is a glow plug connector set designed for preheating glow plugs of 2- and 4-stroke model engines used in automotive, boat, or aircraft model building that run on methanol-containing fuel and features a rechargeable battery. The set comes with a USB charger for recharging the battery. It is important to note that the product is exclusively designed for private use in model building and should not be modified or used for any other purpose to avoid damage or hazards.
The glow plug connector set aids in starting the engine by preheating the glow plug to facilitate fuel ignition. It features an integrated rechargeable battery, eliminating the need for an external power source. The battery can be easily recharged using the supplied USB charger, ensuring convenient and hassle-free operation.
Reely 1611426 is a glow plug connector set designed for preheating glow plugs of 2- and 4-stroke model engines used in automotive, boat, or aircraft model building that run on methanol-containing fuel and features a rechargeable battery. The set comes with a USB charger for recharging the battery. It is important to note that the product is exclusively designed for private use in model building and should not be modified or used for any other purpose to avoid damage or hazards.
The glow plug connector set aids in starting the engine by preheating the glow plug to facilitate fuel ignition. It features an integrated rechargeable battery, eliminating the need for an external power source. The battery can be easily recharged using the supplied USB charger, ensuring convenient and hassle-free operation.
Page is loading ...
Charging the rechargeable battery
Before rst use, charge the rechargeable battery integrated in the glow plug connector with the USB charger
supplied. Connect the jack that sits at the end of the charger cable and is shaped like a glow plug.
• Connect the USB charger to a suitable USB power adapter or USB cigarette lighter adapter (both not
included), which feature an output current of at least 500 mA. Alternatively, you can use the USB port of a
computer or a USB hub that has its own power supply and a current output of 500 mA per port.
The operational readiness of the USB charger is signalled by an integrated green LED.
• Use the nger ring to pull back the plug attachment in the plug connector of the glow plug connector. You
will see the tongs. Insert the connection plug of the USB charger all over until the contact element is fully
surrounded by the tongs. Now let the plug attachment slide forward again by the force of the built-in spring
so that the charger plug is held in place by the tongs.
• The charging process will start, if the battery is not defective (high impedance/interrupted) and power is
supplied. This is indicated by the red LED light on the USB charger.
If the green LED on the USB charger is not on (once connected to a suitable voltage/power
supply), check the power supply to the USB.
The battery is not charging, if the LED is still green and not red. although the glow plug connector
is plugged in. The cause is usually an issue with the contacts (for example, glow plug connector,
spring contacts). Please clean these contacts using appropriate means (for example, contact
spray and soft cloth).
• The recharging process will last for approx. 14 hours if the battery is completely empty. If the rechargeable
battery is only partly discharged, the charging process must be stopped earlier. Check thus the battery
temperature by hand at regular intervals. The charging current is transformed into heat when the recharge-
able battery is fully charged. Thus, the temperature of the rechargeable battery increases noticeably.
• Disconnect the battery from the USB charger after charging and disconnect the USB charger from the
USB voltage/power supply.
Depending on the usage of the glow plug connector, the battery must be recharged in good time
so that delivery of proper glow performance is ensured.
Usage in the model
You should check the functionality of the model and the remote control before heating the glow plug so that
the glow plug connector battery is not exposed to unnecessarily long glow times. When the appropriate
measures are used, such as covering the air supply of the carburettor or similar (depending on the model),
the amount of fuel sucked in will be sufcient.
Pull back the plug attachment with the nger ring at the glow plug connector. Put the glow plug connector
upright on the glow plug and let the nger ring glide forward. The tongs in the glow plug connector must
rmly cup the glow plug.
Hold the glow plug connector and start the engine.
Only pull off the glow plug connector (pull the nger ring) if the engine is running in concentric circles within
the increased idle speed range.
You can test the functioning of the glow plug connector (or whether the battery is sufciently
charged) by connecting an unmounted glow plug to the glow plug connector and view the glow
tip, while holding it in your hollow hand, for example. Attention, risk of burns!
Disposal
a) Product
Electronic devices are recyclable and do not belong in the household waste. Dispose of an
unserviceable product in accordance with the relevant statutory regulations.
Remove any inserted batteries/rechargeable batteries and dispose of them separately from the
product.
b) Batteries/Rechargeable Batteries
As the end user, you are required, by law, (Battery Ordinance) to return all spent batteries/rechargeable
batteries; disposal of them in the household waste is prohibited.
Batteries/rechargeable batteries contain harmful materials and are labelled with the symbol
shown to indicate that disposal in the household waste is forbidden. The symbols of the critical
heavy metals are: Cd = cadmium, Hg = mercury, Pb = lead (the marking can be seen on the
battery/rechargeable battery, e.g., underneath the refuse bin symbol shown on the left).
You can return your used batteries/rechargeable batteries free of charge at the ofcial collection points of
your community, in our stores, or at places where batteries or rechargeable batteries are sold.
That way you full your statutory obligations and contribute to the protection of the environment.
Technical Data
a) USB charger
Operating voltage ...................................... 5 V/DC (USB connection)
Current consumption ................................. 500 mA
Charging current ........................................ 300 mA
Charging time ............................................ max. approx. 14 hours
b) Glow plug connector
Battery type ............................................... NiMH, 1.2 V, 3000 mAh
Dimensions (L x W x H) ............................. 118 x 25.5 x 35 mm
Weight ....................................................... approx. 88 g
Operating Instructions
Glow Plug Connector Kit
Order No. 1611426
Intended Use
The glow plug connector is used to pre-heat a glow plug of 2 and 4-four stroke model engines of model
cars, boats or airplanes, which run on methanol fuels. A rechargeable battery is integrated in the glow plug
connector; the USB charger supplied is used to recharge this battery. The product is designed for private use
within the model making eld only.
For safety and compliance reasons, the product must not be converted or modied in any way. If you use the
product for other purposes than those described above, the product may be damaged. Furthermore, improp-
er use can cause risks such as short-circuits, re, etc. Please read the operating instructions carefully and do
not discard them. Please include these operating instructions when you pass the product on to a third party.
This product complies with the applicable national and European Regulations. All names of companies and
products are the trademarks of the respective owners. All rights reserved.
Package contents
• Glow plug connector with integrated rechargeable battery
• USB charger
• Operating Instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code
shown here. Follow the instructions on the website.
Meaning of symbols
An exclamation mark in a triangle indicates important instructions in these operating instructions
that must be adhered to.
The arrow symbol indicates specic tips and advice on operation.
Safety Instructions
Please read the operating instructions carefully and pay particular attention to the safety
instructions. We do not assume liability for any injuries/material damages resulting from
failure to observe the safety instructions and the information in these operating instruc-
tions regarding the proper use of the product. Furthermore, in such cases, the warranty/
guarantee will be null and void.
• Unauthorised conversion and/or modication of the product is not allowed for safety and ap-
proval reasons.
• The product is not a toy and should be kept out of the reach of children. Therefore, be espe-
cially careful when children are around.
• Do not leave the packaging material carelessly lying around, since it could become a danger-
ous plaything for children.
• The product must not get damp or wet.
• When setting up the product, make sure that the charger cable is neither kinked nor pinched.
• Handle the product with care; it can be damaged by impacts, blows or falls even from a low
height.
• The contacts in the glow plug connector must never be short-circuited, as the battery may
catch re or explode due to the energy stored in there. Protect the tip of the glow plug when
not in use by a small rubber cap, for example.
• Never touch a hot glow plug, the engine, the exhaust silencer, etc., Risk of burns!
• Make sure that you do not reach into the model’s rotating parts (gears, wheels, propellers,
ship’s propellers, etc.) and that your clothes or hair do not get tangled in the drive; Risk of
injury!
• Start the model engine in a way that the car wheels can rotate freely (or, for instance, the
propellers of an airplane or a boat). Use a car starter box or the like or let somebody help you.
Otherwise there is a risk of injury!
• Before starting a combustion engine, check whether the remote control and the receiver are in
good condition (Battery sufciently charged? Transmitter/receiver switched on? Speed lever
on the transmitter in the correct position?).
• If you have doubts about how the product should be operated, its safety or how to connect it,
consult a qualied technician.
• Maintenance, adjustment and repair work should only be carried out by an expert or a spe-
cialised workshop.
• If you have any questions that are not answered in these operating instructions, please con-
tact our technical customer service or other professionals.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1611426_V1_0218_02_VTP_m_en
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
Reely 1611426 is a glow plug connector set designed for preheating glow plugs of 2- and 4-stroke model engines used in automotive, boat, or aircraft model building that run on methanol-containing fuel and features a rechargeable battery. The set comes with a USB charger for recharging the battery. It is important to note that the product is exclusively designed for private use in model building and should not be modified or used for any other purpose to avoid damage or hazards.
The glow plug connector set aids in starting the engine by preheating the glow plug to facilitate fuel ignition. It features an integrated rechargeable battery, eliminating the need for an external power source. The battery can be easily recharged using the supplied USB charger, ensuring convenient and hassle-free operation.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Reely 1611426 Mode d'emploi
- Deutsch: Reely 1611426 Bedienungsanleitung
- Nederlands: Reely 1611426 Handleiding
Related papers
-
Reely 1884848 Operating instructions
-
Reely 1604582 Operating instructions
-
Reely 1780646 Operating instructions
-
Reely 2632378 RY4 4 Channel Gyro Receiver User manual
-
Reely 1687734 Operating instructions
-
Reely 1542913 Operating instructions
-
Reely 1692233 Operating instructions
-
Reely 1695702 Operating instructions
-
Conrad Reely 1970153 Operating instructions
-
Reely DIY X-79 Operating instructions
Other documents
-
VOLTCRAFT VC-30CC-PD Operating instructions
-
TOOLCRAFT 2481637 User manual
-
VOLTCRAFT BC-1001 Operating Instructions Manual
-
-
Renkforce Silent Radio Wi-Fi mouse IR Built-in scroll wheel Owner's manual
-
TOOLCRAFT 2499003 User manual
-
-
-
-
Conrad energy Non-standard battery (rechargeable) 18650 Li-ion 18650 USB 3.7 V 1400 mAh 2 pc(s) Operating instructions
