PAC BKGMK327 User manual

PAC
Brand
PAC
Model
BKGMK327
Type
User manual

This manual is also suitable for

PAC BKGMK327 is a mounting kit designed for Double DIN and Single ISO Mount Applications.

With this kit, you can modify your vehicle's dash to accommodate a new aftermarket radio. It includes various brackets, spacers, and clips, allowing you to securely mount your new radio in place. The kit's versatility makes it compatible with a range of vehicles, including 2015 Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL.

Here are some notable features and capabilities of the PAC BKGMK327:

  • Compatibility: Specifically designed to fit 2015 Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles.

PAC BKGMK327 is a mounting kit designed for Double DIN and Single ISO Mount Applications.

With this kit, you can modify your vehicle's dash to accommodate a new aftermarket radio. It includes various brackets, spacers, and clips, allowing you to securely mount your new radio in place. The kit's versatility makes it compatible with a range of vehicles, including 2015 Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL.

Here are some notable features and capabilities of the PAC BKGMK327:

  • Compatibility: Specifically designed to fit 2015 Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles.
Double DIN Mount Applications
1. Remove the Shaded tab from the back edge of each left and right mounting bracket
(right side not shown).
2. Cut and remove center rib from main bracket and file smooth.
3. Attach the left and right side brackets to the main bracket (See Figure D).
4. Insert ISO mountable radio between ISO mount brackets and loosely attach to sidesof radio
using screws provided with radio when possible or hardware included with kit.
NOTE: Use longer screws in kit for upper radio location.
5. Slide radio component forward or backward for desired look and tighten screws.
6. Attach a rear support bracket to the rear of the new radio and adjust as necessary to attach
to the rear support stud located on the back of the pocket using the small phillips screw
supplied with kit (optional). Phillips screw supplied with kit (optional).
7. Attach (1) of the metal spring clips included to each of the (3) mounting studs
on the top side of the kit Or the OEM clips can be removed from the factory radio and be used.
8. Reinstall dash pad.
Attach (1) ISO Spacer to the inside of upper sections
on both Left & Right mounting brackets
as shown in
Fig. B.
Cut
Fig. B
UNIT2
CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
©2014 AMERICAN INTERNATIONAL INDUSTRIES, INC.
Chevrolet
2015 Tahoe
2015 Suburban
GMC
2015 Yukon
2015 Yukon XL
VEHICLE APPLICATIONS
KIT ASSEMBLY INSTRUCTIONS
Fig. D
Remove the Shaded tab from the back
edge of each left and right mounting
bracket (right side not shown).
GMK327 Mounting Kit
TECH Ver. 9/14 PRINT Ver. 0/14
iGMK327
Right
UNIBRK
Cut
NOTE: ISO trim ring (UNIT2) may be used in place of after-market radio’s trim rings. For ISO mount
applications, mount after-market radio components to side brackets using screws provided with radio
when possible or hardware included with kit.
Left
UNIBRK
Single ISO Mount Applications
1. Attach the left and right side brackets to the main bracket (See Figure C).
2. Insert pocket (part # UNIPOC) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Attach (1) ISO Spacer to the inside of upper section on both Left & Right mounting
brackets as shown in Fig. B.
5. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides
of radio using screws provided with radio when possible or hardware included with kit.
NOTE: Use longer screws in kit for upper radio location.
6. Slide radio component forward or backward for desired look and tighten screws.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary to
attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit (optional).
NOTE: ISO trim ring (UNIT1) may be used in place of after-market radio’s trim rings.
8. Attach (1) of the metal spring clips included to each of the (3) mounting studs on the
top side of the kit Or the OEM clips can be removed from the factory radio and be used.
9. Reinstall dash pad.
DASH DISASSEMBLY INSTRUCTIONS KIT ASSEMBLY INSTRUCTIONS
2 3
Attach (1) ISO Spacer to the inside of upper
sections on both Left & Right mounting brackets
as shown in
Fig. B.
Fig. C
UNIT1
(Optional)
UNIPOC
Left
UNIBRK
Right
UNIBRK
NOTE: These instructions are a guideline... different trim levels and models will have
slight variations in the removal process.
1. Unsnap and remove dash trim piece from the right of the radio to above the glove box.
2. Remove (2) Torx screws and unsnap / loosen panel below steering wheel,
no need to remove.
3. Remove (2) 7mm screws for the bottom of main radio/climate control trim.
Remove trim.
4. Remove (1) 7mm screw ,unsnap and remove dash trim piece from the left
of the driver’s side air vent.
5. Unsnap and remove center console trim piece from below the climate controls.
6. Remove (3) 7mm screws from each air vent, located to the left and right of the radio.
Remove both vents.
7. Remove (4) 7mm screws from the radio panel.
8. Remove radio and climate controls. Unplug all harnesses.
9. Remove dash pad from top of radio, save for kit assembly.
Single DIN Mount Applications
1. Attach the left and right side brackets to the main bracket.
2. Insert pocket (part # UNIPOC) into lower section of the main frame.
3. Attach left and right side brackets to the rear of the pocket using screws supplied.
4. Insert DIN sleeve from your new radio into the upper section of
the installation kit.
5. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
6. Install radio into sleeve and lock into place.
7. Attach a rear support bracket to the rear of the new radio and adjust as necessary
to attach to the rear support stud located on the back of the pocket using the small
phillips screw supplied with kit (optional).
8. Attach (1) of the metal spring clips included to each of the (3) mounting studs on the
top side of the kit Or the OEM clips can be removed from the factory radio and be used.
9. Reinstall dash pad.
KIT ASSEMBLY INSTRUCTIONS
UNIPOC
UNIT1
(Optional)
Left
UNIBRK
Right
UNIBRK
DIN SLEEVE
Fig. A
Fig. B
  • Page 1 1
  • Page 2 2

PAC BKGMK327 User manual

PAC
Brand
PAC
Model
BKGMK327
Type
User manual
This manual is also suitable for

PAC BKGMK327 is a mounting kit designed for Double DIN and Single ISO Mount Applications.

With this kit, you can modify your vehicle's dash to accommodate a new aftermarket radio. It includes various brackets, spacers, and clips, allowing you to securely mount your new radio in place. The kit's versatility makes it compatible with a range of vehicles, including 2015 Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL.

Here are some notable features and capabilities of the PAC BKGMK327:

  • Compatibility: Specifically designed to fit 2015 Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents