Etec SPOTWASH E3048 User manual

LED Moving Head

SPOTWASH E3048

Page | 2

Congratulations!

You have acquired an excellent and innovative product from ETEC. In order to ensure the greatest

possible performance of the device, read this manual carefully and familiarize yourself with the most

important functions. This manual contains important information on the operation and maintenance

of this unit. Please keep this manual for future reference, together with the device.

unpacking:

Please unpack the product immediately after receiving and check it for completeness and integrity. If

you notice any damage to the transport of one or more parts of the product or package, please notify

the seller immediately and collect the packaging material for later inspection. Keep the carton and all

related packaging materials. If the product needs to be returned, please make sure you return it in

the original packaging.

Provisional useful life of the LED headlamp:

The brightness of LEDs decreases with time. The main cause is HEAT because it speeds up the

process. When LEDs are placed very close together, they are exposed to a higher operating

temperature than when an ideal distance is maintained or operated under optimal conditions, ie

individually. For this reason, the useful life is significantly reduced when all color LEDs are operated

with maximum brightness. The service life achievable under normal operating conditions is

approximately between 40,000 and 50,000 hours. If the prolongation of the service life is of great

importance to you, you should ensure that the operating temperature is kept low. An air-conditioned

operating environment and the reduction of the overall luminous intensity can contribute to this.

Warning:

DANGER!

Protect the device from rain and moisture!

Disconnect the power cord before opening the housing!

PLEASE READ THESE INSTRUCTIONS FOR YOUR SAFETY CAREFULLY,

BEFORE OPERATING THE UNIT FOR THE FIRST TIME!

safety instructions:

All persons who install, operate and maintain this equipment must:

• be qualified and

• Follow the instructions in this manual.

ATTENTION! Be careful when handling this unit. In the case of

dangerous mains voltages, you could get a life-threatening electric

shock when you touch the cables!

Page | 3

Before using the appliance for the first time, ensure that the product has not been damaged by

transport. If it is damaged, please contact the seller and do not use it. In order to ensure the perfect

condition and the safe handling, the safety instructions and warnings in this manual must be

observed.

Please note that we assume no liability for damages caused by manual changes. This device does not

contain any user-serviceable parts. Only carry out maintenance work by qualified technicians.

Important Safety Information:

The manufacturer is not liable for damage caused by the failure to observe this manual or

unauthorized modifications to this product.

• The power cord must never come into contact with other cables! Use the power cord and

all connections to the power supply.

• Do not remove the warnings and information labels from the product.

• The grounding contact must never be tampered.

• Make sure that no cables are around.

• Do not insert objects into the ventilation slots.

• Do not connect this unit to a dimmer pack.

• Do not open or modify the unit.

• Never use the appliance during a thunderstorm. In the event of a thunderstorm, unplug the

power cord immediately.

• Never look directly into the light source.

• Do not turn the unit on and off at short intervals as this will reduce the lifetime of the unit.

• Do not expose the unit to shocks. Do not use excessive force when installing or using the

device.

• Use the product only in indoor areas and avoid contact with water or other liquids.

• Check that the housing is tightly closed and that all screws are tightened before using the

appliance.

• Do not place the product near open fires or flammable liquids or gases.

• Always allow at least 50cm clearance around the unit to ensure adequate ventilation.

• Always unplug the unit when not in use or when you want to clean it. Only hold the mains

cable at the provided area on the plug. Never unplug the cord from the wall outlet.

• Protect the product from extreme heat, moisture or dust.

• Make sure that the available mains voltage is not higher than indicated on the back of the

unit.

• Do not crush or damage the power cord. Check the unit and the power cord at regular

intervals for possible damage.

• If the connection cable is clearly damaged, it must be replaced.

• If the lens is clearly damaged, it must be replaced so that the functions of the unit are not

affected by cracks or scratches.

• Disconnect the appliance immediately from the power supply if it falls or becomes severely

damaged.

• Have the unit checked for safety by a qualified technician before using it again.

• Do not turn off the unit immediately after exposure to strong temperature fluctuations (eg

during transport). The resulting condensation could damage the unit. Do not turn the unit on

until room temperature is reached.

Page | 4

• Turn the power off immediately if it is not working properly. Pack the device carefully

(preferably in the original package) and send it to your dealer.

• Suitable for adult use only. The light-emitting device must be placed out of the reach of

children. Never leave the connected device unattended.

• Only use replacement fuses of the same type and performance as the fuses already

contained.

• The user is responsible for the correct positioning and correct operation of the device. The

manufacturer is not liable for damages caused by incorrect use or incorrect installation.

• The unit falls under protection class I. Therefore it must be earthed with the yellow-green

cable.

• There may be too little smoke or odor during initial start-up. This is not unusual and does

not necessarily mean that the device is not working properly.

• Repairs, maintenance and electrical connections may only be carried out or handled by

qualified technicians.

ATTENTION! EYE DAMAGE!

Never look directly into the light source.

(Especially epileptics)!

Intended Use:

• This unit is not suitable for continuous operation. Maintaining regular operating breaks

increases the life of the unit.

• The minimum distance between the light source and the illuminated area is 0.5 meters.

• The maximum ambient temperature for operation is ta = 45 ° C and must never be

exceeded.

• The relative humidity must not exceed 50% at an ambient temperature of 45 ° C.

• If the appliance is not used as described in this manual, it could be damaged and the

warranty void.

• Any improper use will lead to risks such as: Short circuits, burns,

• Electric shock, crashes, etc.

Your safety and the people you surround are in danger!

Installation:

Observe the European and international guidelines for installation, mounting on trusses and all other

safety measures. Do not attempt to install the unit yourself! Always have the installation carried out

by qualified personnel!

Page | 5

The mounting stand or the installation wall must be capable of carrying 10 times the weight of the

appliance without deforming. When attaching, the device must be secured with a second safety

fixture, such as a suitable safety cable. Never place yourself directly underneath the unit during

fixing, dismantling or maintenance.

Overhead mounting requires a professional experience, including calculating the load capacities, the

mounting material used, and periodic safety inspections of the entire mounting material and

equipment. If you do not have these qualifications, you should refrain from performing an

installation yourself. The installation should be inspected once a year by a suitably trained specialist.

power connections:

Connect the device to the power supply with the mains cable. Always ensure that the colored cables

are connected to the appropriate, correct locations.

International

Europe Cable

UK Cable

USA Cable

L

BROWN

RED

YELLOW / COPPER

PHASE

N

BLUE

BLACK

SILVER

ZERO

YELLOW-GREEN

GREEN

GROUND

Make sure that the device is always properly grounded!

disposal:

Do not throw the appliance into normal household waste at the end of its useful life.

This product is subject to European Directive 2002/96 / EC.

• Dispose of the product through an approved disposal company or through

your municipal waste disposal facility.

• Observe the current regulations. If in doubt, contact your disposal facility.

• The packaging is certified by a dual system. Dispose of all packaging materials in an

environmentally friendly manner according to local regulations.

maintenance:

The device is almost maintenance-free. Nevertheless, the device should be cleaned regularly. If the

appliance is not cleaned regularly, the light output of the appliance will be considerably reduced over

time. Disconnect the unit from the mains and wipe it with a damp cloth. Never immerse the unit in

any liquid. Clean the unit with a soft cloth. Do not use alcohol or solvents. The connections should

Page | 6

also be cleaned regularly. Disconnect the device from the mains and wipe the connections with a

cloth. Ensure that all connections are completely dry before you connect or reconnect the device to

other devices.

The operator must ensure that all safety-relevant and mechanical devices are subjected to a

technical inspection test by qualified personnel after four years. The operator must ensure that all

safety-related and mechanical devices are inspected once a year by qualified personnel.

The following points must be considered during the verification:

1. All screws used to install the product or parts of the product must be secure and not

corroded.

2. Neither housing nor fastenings or the areas to which the product is attached may be

deformed.

3. Mechanically moved components, such as axles, lenses, etc., must not have any wear

marks.

4. Power cables must be undamaged and must not show any signs of material fatigue.

Replace fuse:

Overvoltages, short circuits or unsuitable mains connections can cause a fuse to burn through. The

device does not work when the fuse is blown. If your device burns a backup, perform the following

steps.

1. Disconnect the mains plug.

2. Insert a flat screwdriver into the slot of the fuse cover. Lever the cover gently. The fuse now comes

to light.

3. Remove the old backup. If you look brown or milky, it is burned.

4. Insert the new fuse into the holder. Close the cover. Use only a fuse of the same type and the

same specifications. Observe the label with the technical data.

Page | 7

Product description:

The ETEC SPOTWASH E3048 is a 2in1 LED Moving Head and combines a spot moving head and a wash

light in a single device. It is equipped with a white 30 Watt LED Spot with 11° beam angle. Further

features of the moving head 6 extremely bright 10W 4in1 RGBW LEDs with 25° beam angle. The

combination of spot and wash effect, can produce new unique effects with just one fixture. Another

highlight the spot moving head has a motorized focus and a gobo wheel with 7 gobos.

Thanks sound to light and automatic mode with 8 programs the E3048 can be used immediately. A

master / slave control and DMX 10 or 17 channels is also possible. The SPOTWASH provides pan and

tilt movements of 540° and tilt 270° and a color wheel with 7 colors + white. The real RGBW color

mixing of the lens ensures perfect colors on the stage, in the club, at shows, TV studios and in many

other applications. The large LCD display, all functions using 4 keys can be set easily.

Technical specifications:

Power consumption: 95W

Power supply: 100 - 240V

Voltage frequency: 50 / 60Hz

Diod Type: Single / 4in1

Number of diodes: 1/6

Diode Power: 30W / 10W

Beam angle: 11 ° / 25 °

Display: LCD matrix

Color: color wheel / RGBW

Dimmer: Linear: 0 - 100%

Number of DMX channels: 10 or 17

DMX standard: DMX 512

Control interface: 4 buttons

Operating modes: DMX512, automatic, music-

controlled, manual, master / slave

AC IN: powerCON

DMX IN: XLR - 3-pin

DMX OUT: XLR - 3-pin

Protection class: IP20

Housing: ABS

Measurements: 200x190x330mm

Weight: 4.2 kg

Page | 8

Product Overview:

1. LED Diode

2. Display

3. Display &Buttons: Mode, Up, Down, Enter

4. DMX linking IN/OUT

5. PowerCON IN

Functions and settings:

LCD display

MENU: Function mode selection, such as DMX, Master / Slave, Auto, Sound Mode and Brightness

settings

DOWN / UP: Previous or Next function

Enter: Confirm and save the selection

1.

6.

5.

2.

3.

Page | 9

Menu overview:

Page | 10

Press ENTER

to confirm

You can display the low menu only with P018

Page | 11

Setting up a DMX connection:

Page | 12

DMX is a standardized transmission protocol that allows all DMX-compatible models of the various

manufacturers to be connected to one another and controlled by a single mixer. Free DMX data

transfer between different DMX devices are used.

The connection arrangement between the devices has no influence on the DMX addressing. For

example, DMX address 1 has been assigned to a device, and the DMX connection position can be

positioned at the beginning, at the end or anywhere in the middle.

Therefore the first device, which is controlled by a controller, can be the last one in a row at the

same time. When the DMX address 1 has been assigned to a device, the DMX controller knows which

addressers the data send filter, no matter where the DMX cable is located.

Resistance 120 ohms 1 / 4w between PIN 2DMX -) and PIN 3 (DMX +) of the last headlight.

Caution: Avoid contact between the general and the housing grounding of the headlight. The general

grounding may cause a loop and your headlight could only function irregularly. Test the cables with a

resistance meter to check the correct polarity and to ensure the correct polarity.

Connecting the headlights:

If you want to control light shows with one or more devices with a DMX-512 controller, or you want

to play synchronized shows with two or more devices in master / slave mode, you must use a serial

data transmission line. The total number of channels required by all devices determines the number

of devices that the data transmission line can support.

The devices connected to a serial data transmission line must be connected in series. According to

the standard EIA-485, no more than 30 devices should be connected to a data transmission line.

However, if you connect more than 30 devices to a serial data transfer line without using an optical

splitter, the quality of the DMX signal may be degraded.

• Maximum recommended length of the DMX data transmission line: 100m

• Maximum recommended number of headlights on a DMX data transmission line:

30 devices

• with 220V: Up to 6 units can be connected in series

DMX Channel assignment:

Page | 13

Page | 14

Final Note:

Technical and optical changes within the scope of product improvement are reserved - even without

prior notice.

No liability shall be accepted for printing errors and resulting faulty operation. If in doubt, consult

your ETEC dealer!

Page | 15

Space for your notes:

_________________________________________________________________________________

Page | 16

Importeur

Hansaring 138-142

48268 Greven

Germany

Fon: +49 (0) 25 71 - 80 5 40 42

Fax: +49 (0) 25 71 - 80 5 40 41

www.etec-professional.de

Etec SPOTWASH E3048 User manual

Etec SPOTWASH E3048 User manual

Related papers

Other documents