Miele PT7138W Installation guide

Installationsplan / Installation plan

Installatietekening

Plan d`installation

Piano di installazione

Plano de instalación

Plano de instalação

Σχέδιο εγκατάστασης

Asennusohje

Installasjonsplan

Installationsplan

G

PT 7136 / PT 5136 EL

Materialnummer / Mat. no.: 06 664 260

Änderungsstand / Version: 02

Datum Zeichnung / Drawing date: 25.04.2005

Datum Legende / Legend date: 15.11.2007

Installationsplan PT 7136 / PT 5136 EL

Stand: 15.11.2007 Seite 8

Technical datasheet

Tumble dryers:

Heating:

PT 7136 / PT 5136

Electric (EL)

Legend:

Circled, bold-type abbreviations:

Connection required

Abbreviations surrounded by broken circle:

Connection optional or required, depending on model

G

Optional extras:

UG/UO 5005 Miele plinth

(UG = Box plinth/UO = Open plinth)

UM

Height Model mm 300

Width UG (UO) mm 609 (598)

Depth UG (UO) mm 622 (615)

Concrete platform Concrete platform optional (Min. quality B15)

Recommended height mm 300

BS

Minimum height mm 100

Recommended width mm 600

Recommended depth mm 650

Ensure good anchorage!

Machine connections:

1. Standard voltage (as supplied) V 3N AC 400

Frequency Hz 50

Rated load kW 6.4

Fuse rating A 3 × 10

Electrical

connection

D

Connection cable, min. cross-section mm² 5 × 1.5

Length of supply lead (H05 RN-F without plug)

(supplied)

mm 2000

1. Alternative voltage V 3 AC 230

Frequency Hz 50

Rated load kW 6.5

Fuse rating A 3 × 16

Supply lead as above

convertible

2. Alternative voltage V 1N AC 230

Frequency Hz 50

Rated load kW 3.35

Fuse rating A 1 × 16

Supply lead as above

convertible

3. Alternative voltage V 1N AC 230

Frequency Hz 50

Rated load kW 2.24

Fuse rating A 1 × 10

Supply lead as above

convertible

Country variations:

2. Standard voltage (as supplied) V 1N AC 220 - 230

Frequency Hz 50

G i

Rated load kW 5.08 – 5.52

Fuse rating A 1 × 25

Connection cable, min. cross-section mm² 3 × 2.5

Length of supply lead (H05 RN-F without plug)

(supplied)

mm 2000

Installationsplan PT 7136 / PT 5136 EL

Stand: 15.11.2007 Seite 9

3. Standard voltage (as supplied) V 3 AC 230

Frequency Hz 50

N

Rated load kW 6.4

Fuse rating A 3 × 16

Connection cable, min. cross-section mm² 4 × 1.5

Length of supply lead (H05 RN-F without plug)

(supplied)

mm 2000

4. Standard voltage (as supplied) V 1N AC 230-240

Frequency Hz 50

W

Rated load kW 5.52 – 6.0

Fuse rating A 1 × 25

Connection cable, min. cross-section mm² 3 × 2.5

Length of supply lead (H05 RN-F without plug)

(supplied)

mm 2000

5. Standard voltage (as supplied) V 3 AC 208

Frequency Hz 60

V U

Rated load kW 6.4

Fuse rating A 3 × 24

Connection cable, min. cross-section mm² 4 × AWG 10

Length of supply lead (H05 RN-F with plug)

(supplied)

mm 2000

Alternative voltage V 2 AC 208

Frequency Hz 60

Rated load kW 4.4

Fuse rating A 2 × 24

Supply lead as above

convertible

6. Standard voltage (as supplied) V 2N AC 200

Frequency Hz 50-60

J

Rated load kW 4.0

Fuse rating A 2 × 20

Connection cable, min. cross-section mm² 3 × 2.75

Length of supply lead (H05 RN-F with plug)

(supplied)

mm 2000

Non-standard voltages:

1. Standard voltage (as supplied) V 3 AC 230

Frequency Hz 60

OS 230

Rated load kW 6.4

Fuse rating A 3 × 16

Connection cable, min. cross-section mm² 4 × 1.5

Length of supply lead (H07 RN-F without plug)

(supplied)

mm 2000

2. Standard voltage (as supplied) V 3 AC 400

Frequency Hz 50

OS 400

Rated load kW 5.35

Fuse rating A 3 × 10

Connection cable, min. cross-section mm² 4 × 1.5

Length of supply lead (H07 RN-F without plug)

(supplied)

mm 2000

3. Standard voltage (as supplied) V 3 AC 440

Frequency Hz 60

OS 440

Rated load kW 6.4

Fuse rating A 3 × 10

Connection cable, min. cross-section mm² 4 × 1.5

Length of supply lead (H07 RN-F without plug)

(supplied)

mm 2000

Installationsplan PT 7136 / PT 5136 EL

Stand: 15.11.2007 Seite 10

Plug and socket connection in accordance with IEC 60309

recommended to facilitate electrical safety tests.

Install mains isolator according to IEC 60947 on hard-wired

connection.

Wall socket or mains isolator must be accessible after

installation.

The use of an earth leakage circuit breaker (ELCB) is strongly

recommended.

If necessary, equipotential bonding with good galvanic contact

must be provided in accordance with all appropriate national

and local regulations.

Nominal air throughput in vented mode (at 60Hz) m³/h 300 (340) Vented

Permissible pressure attenuation (at 60Hz) Pa 320 (480)

Machine vent connection (d

ext

× s × l) [DN 100] mm 100 × 0.6 × 78

On-site vent connection (interior diameter) mm 100

Max. temperature °C 80

As relative humidity can be as high as 100%, suitable

measures must be taken to prevent a backflow of condensate

into the machine.

If the machine fan is unable to transport air over the on-site

vent ducting distance, an additional fan with a suitable

capacity must be installed either in the ducting or at the point

of discharge to atmosphere.

Standard connection:

Air intake from installation site

Air intake

Recommended air intake vent cross-section cm² 237

(to prevent draughts in installation site)

Sufficient air intake should be available to replace displaced

volume of air.

Miele plinth UG/UO 5005 Fittings (supplied)

4 × metal angled brackets (to secure machine to plinth)

4 × screws DIN 571 (Ø × length) mm 8 × 65

4 × rawl plugs (Ø × length) mm 12 × 60

Machine must be bolted to the floor!

Fixing materials for floating screed floor to be provided on site

On concrete platform

2 × screws DIN 571 (Ø × length) mm 6 × 50

2 × rawl plugs (Ø × length) mm 8 × 40

Machine must be bolted to the floor!

Fixing materials for floating screed floor to be provided on site

Without plinth

2 × screws DIN 571 (Ø × length) mm 6 × 50

2 × rawl plugs (Ø × length) mm 8 × 40

Machine must be bolted to the floor!

Fixing materials for floating screed floor to be provided on site

Payment system

Installationsplan PT 7136 / PT 5136 EL

Stand: 15.11.2007 Seite 11

The following extensions are possible:

Installation of payment system

Possible

extensions

Installation as washer-dryer stack

Connection to serial interface, RS 232

Machine data Width mm 595

Depth mm 700

Height mm 850

Knocked-down dimensions (W × H) mm 600 x 900

Recommended rear wall gap (measured to front of machine) mm 1100

Net weight kg 58

Dynamic floor load, max. N ~ 670

Average heat dissipation

(dependent on ambient room temperature and programme

selected)

W 215

Acoustic power level (re1 pW) dB (A) 65

Sound pressure level

(measured at a distance of 1 m from the machine and at a

height of 1.6 m)

dB (A) approx. 52

Installation should only be carried out by authorised fitters in accordance with valid regulations!

Miele PT7138W Installation guide

This manual is also suitable for

Miele PT7138W Installation guide

Related papers

Other documents