GORILLA GADGETS
TM
JungleConcert
TM
Premium Bluetooth
TM
Headphone
User Guide
Table of Contents
1. Introduction 3
2. Safety 3
3. Package Contents 4
4. Control Diagram 4
5. User Guide 5
5.1 General Use 5
5.2 Pairing to a mobile phone or other Bluetooth
TM
–enabled device 7
5.3 Pairing to a computer 8
5.4 Wired Line-in Input 8
5.5 USB Audio Input 8
5.6 Charging your JungleConcert
TM
Stereo Headphone 9
7. Service and Support 10
8. Frequently Asked Questions (FAQ’s) 10
1. Introduction
Whether you’re in the rain forest or deep in the urban jungle, you’re
going to love your new JungleConcert
TM
Bluetooth
TM
Stereo
Headphones. This brief instruction manual will help you become
familiar with all the features that are built into your headphone, and we
strongly advise you to read it before attempting to connect. But if
you’re like 99% of the other gorillas out there, you’ll pop open the
package, go as far as you can, and then check out this booklet when you
get stumped. That’s OK, too, but don’t say we didn’t tell you so…
2. Safety
It’s like, really hard to hurt yourself with a battery-driven stereo
headphone, but someone will figure out a way, so we’re going to tell you
the obvious here:
1) Read the manual before you use the headphone. It has a lot of
good information in it.
2) Watch for sharp edges, uneven surfaces, or metal parts that could
scratch or cut you.
3) Don’t try to modify, repair, or dismantle this headphone. Doing so
could result in fires, electric shocks, complete destruction of the
headphone or worse, all of which will not be covered under your
warranty. So don’t do it. Send it to us if it’s under warranty, and
we’ll either replace it or repair it for you.
4) Don’t use solvents or volatile liquids to clean your JungleConcert
headphone.
5) Don’t use your JungleConcert Headphone in any area that could be
considered hazardous – especially those areas where you need to
be hearing what’s going on around you.
3. Package Contents
• JungleConcert Bluetooth
TM
Stereo Headphone
• USB Charging Cable
• Audio Cable
• User Manual
• Carrying case
4. Control Diagram
5. User Guide
5.1 General Use
To do this:
Follow these instructions:
Turn on
Press the MFB button for 3 seconds when the device is
off. A pink LED will slowly flash and you’ll hear a tone
beeping.
Enter the Pairing
Mode
Press the “+/-“ button with the power on, and hold it for 6
seconds. A white and red LED will alternately flash and
you’ll hear a two beep tone.
Pairing
You can pair with your mobile phone or any other Bluetooth
enabled master device
Turn Off
Press the MFB button for 3 seconds when the device is in
the ‘on’ mode. You’ll hear a tone beep and all the LED lights
will go off.
Low Battery
Warning
The red LED will flash continuously.
Charging
Plug your USB (supplied) cable into the built-in port
Answer a Call
Touch the MFB button when you know there’s a call coming
in.
End a Call
Same thing. Touch the MFB button and you’ll disconnect
the call.
Shift between
two devices
Double press the MFB button to transfer from one device to
another; ie.to answer a call or to go from a call to another
device.
Reject a call
Press the MFB button for 1-2 seconds to reject an incoming
call.
Volume Up
A short press on the “+” button will take the volume up a
notch.
Volume Down
A short press on the “-“ button will knock the volume down
a notch.
Next
A short press on the “>” button will advance you to the next
selection.
Previous
A short press on the “<” button will take you back to the
previous selection
Battery Power
Indication
When you pair to an iPhone, the battery power on your
headphone will be indicated on your iPhone.
Play/Pause
A short press of the “>” key will play or pause the music
when your headphone is connected.
Multi-point
Connection
In pairing mode, short press the “>” button to enable the
multi-point option; double press the MFB to disable the
multipoint option.
Factory Reset
Long press both “>” and “<” when you’re in the pairing mode
to reset or clear the paired device list.
5.2 Pairing to a mobile phone or other Bluetooth
TM
–enabled
device
To use your JungleConcert Bluetooth
TM
Headphone, you must first pair your
headphone with a phone or a computer that is also Bluetooth
TM
enabled. Once
your headphone is paired to a specific phone or computer, it will remain paired
and will automatically recognize each other whenever they are within range.
1) Turn on your phone and make sure the Bluetooth
TM
function has been
activated
2) Turn on your JungleConcert Headphone and go to the pairing mode
3) Search the list of Bluetooth
TM
devices available on your phone by
following your phone’s instructions. Refer to your phone’s instruction
manual if you still have it.
4) After a few seconds, the phone will detect the JungleConcert
headphone as a ‘discovered’ device. Select it, and follow your phone’s
instructions to select this particular pairing.
5) Your phone may request a Passkey or PIN; enter 0000 as your PIN or
Passkey.
6) Your phone will confirm the pairing. Press ‘Yes’ or ‘OK’ if it asks.
Select the option to connect with the device from your phone’s
screen.
7) You can play music, watch TV or a movie, or play games on your phone
while listening to the audio on your JungleConcert Stereo Headphones.
You can control the audio from the headphone using the touch control
panel on the side.
5.3 Pairing to a computer
1) Make sure your computer is Bluetooth
TM
enabled. If it is not, you will
need to acquire a Bluetooth
TM
adapter. Once it is in place, make sure
the Bluetooth
TM
function is activated.
2) Turn on your JungleConcert Headphone and go to the pairing mode
3) Open the Bluetooth
TM
software that is installed on your computer, and
then select the option that searches for Bluetooth
TM
devices. Refer to
the software manual if you still have it.
4) After a few seconds, the name of your device will be listed on your
computer as a ‘discovered device”.
5) Select the device’s icon and click the right-side button on your mouse
to choose the ‘Pairing’ option; then select “connect with audio device”.
6) Go to your media player, or whatever program you want to transfer the
audio from, and listen in complete privacy to the clean, clear sounds.
5.4 Wired Line-in Input
Your JungleConcert Stereo Headphone supports a 3.5mm audio jack
line-in cable if you should desire to go that way. The only reasons we
can think of are if the batteries go low, or if wireless devices aren’t
permitted wherever you are. When you use the line-in cable, the
Bluetooth
TM
option will automatically power off.
5.5 USB Audio Input
You can charge your JungleConcert Stereo Headphone and listen to
music at the same time when you connect it with the USB cable to your
computer.
5.6 Charging your JungleConcert Stereo Headphone
Your Headphone uses a USB – to – Micro USB charger. Make sure that
your JungleConcert headphones are fully charged (at least 6 hours)
before your first use. When the headphone is charging, you’ll see a red
LED light in the constant ‘on’ mode. When charging is complete, the red
LED will go off, and a white LED will go on.
Warning:
You must fully charge your JungleConcert Headphone if it has not
been used for more than 12 months.
6. Technical Specifications
7. Service and Support
If you believe your JungleConcert Headphone is not working
properly, please contact Gorilla Gadgets Customer Service. Our
contact information is available at www.gorillagadgets.com.
8. Frequently Asked Questions (FAQ’s)
The headphone doesn’t show any power, even when it’s
turned on.
Make sure you’ve charged the battery for up to 6 hours
when you use it for the first time. The LED will be a solid
red while charging, and will turn white when it’s done
charging.
There is no sound coming from my headphone
Check the connection between your headphone and your
phone or computer/laptop. If the connection is not
established, follow the instructions to reconnect. Make
sure the headphone is paired or connected with your
target phone or other master device.
I can’t seem to connect the headphone to a second device
Set the headphone to ‘pairing mode’, and do a short
press on the “>” button to multipoint mode. Connect the
headphone to phone #1. Press the “+” and “-“ buttons
for 6 seconds to enter the pairing mode again and then
connect the headphone to phone #2. Then use phone
#1’s paired device list to reconnect to the headphone.
/
