2. Atdec
  3. SD-WD
SD-WD

Atdec SD-WD User manual

  • Hello! I've reviewed the installation instructions for the Spacedec SD-WD Display Wall Mount. This document provides details on how to install the mount on various types of walls, and how to attach your display. It also mentions the use of a VESA ball mount to enable viewing angle adjustment. Feel free to ask me any questions you may have about it.
  • What is the maximum weight this wall mount can support?
    What VESA hole patterns are supported by this product?
    What are the required tools for installation?
    How do I adjust the tension of the VESA ball mount?
Component Checklist
Step 1. Component Checklist
Check you have received all parts against the Component Checklist above.
Installation Instructions
Wall Mount
Assembly (x1)
Step 2. Installing the Wall Mount Assembly (choose from one of the following options)
For mounting Spacedec to a Timber Stud Wall - Using the Wall Mount Assembly Bracket, mark
the location of the 4 holes and drill using a 4mm drill bit. Secure the bracket to the wall using the M6 Coach
Screws as shown in diagram A.
For mounting Spacedec to a Masonry Wall - Using the Wall Mount Assembly Bracket, mark
the location of the 4 holes and drill using an 8mm masonry drill bit. Secure the bracket to the wall using the M6
Coach Screws and Nylon Anchors as shown in diagram B.
A. Timber Stud Wall B. Masonry Wall
Note: This product will suit VESA compliant monitors with 75mm x 75mm (3” x 3”) and 100mm x 100mm (4” x 4”) hole patterns only.
It will support up to a maximum weight of 25kg (55lbs).
Display | Wall Direct
SD-WD
VESA
plate (x1) Hardware
Mounting Fasteners
M4x10mm
Screw (x4) M4x12mm
Screw (x4) M4x16mm
Screw (x4)
(Optional)
Security
Screw (x1) M6 Coach
Screws (x4)
Nylon
Anchor (x4)
Combined 3mm
Allen Key and
Phillips-head
Screwdriver (x1)
Wall Mount Assembly
Bracket
M6 Coach
Screw
4 x 4mm
Holes
Wall Material
Stud

TOOLS REQUIRED:
• Power Drill
• Phillips-head Screwdriver
• 4mm (3/16”) Drill Bit
• 8mm (5/16”) Masonry Drill Bit
• 8mm (5/16”) Socket Wrench
or Shifter
Wall Mount Assembly
Bracket
M6 Coach Screw
4 x 8mm
Holes
Masonry Wall
Nylon Anchor
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 23.11.11 ©
Installation Complete
There are two mounting hole configurations:
• 75 x 75mm
• 100 x 100mm
Choose appropriate Mounting Screws
from the Hardware supplied to suit
your Display. Top of
Display
Mounting Screws (x4)
VESA Plate
Back of Display
75mm
(3”) 100mm
(4”)
75mm
(3”)
100mm
(4”)
Step 4. Attach your Display to the Wall Mount Assembly
Step 5.
Adjust the VESA Ball Mount
Step 3. Attach the VESA plate to your Display
Position your Display to the desired viewing angle, using the 20°
angular movement allowed by the VESA Ball Mount.
Depending on the weight of the display, it may be necessary to make
adjustments to the VESA Ball Mount. If the display does not hold its
position, or is too resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount (see diagram right).
To make any adjustments tension evenly using the 3mm Allen Key
supplied. Apply half a turn at a time to each screw on the Tension
Plate to adjust evenly.
Check the display, and then adjust again if necessary.
Loosen (-Kg)
Tension
Plate
Tighten
(+Kg)
Combined Phillips-head
Screwdriver/Allen Key
supplied
(Optional) Insert the Security Screw
supplied and tighten using a
Phillips-head Screwdriver.
Press and hold the Release Buttons.
Gently insert bottom of VESA Plate
into Quickshift Mount. Release
Buttons to lock
in place.
Security
Screw
Hook the top of the VESA Plate onto
the VESA Ball Mount.
Back of Display
Combined Phillips-head
Screwdriver/Allen Key
supplied
/