Barco Events Controller Installation guide

EVENTS

BAR CO EVENTS CONTROLLER

INSTALLATION GUIDE

With diagnostics guide

15052003 R5976619/00

Barco nv Events

Noordlaan 5, B-8520 Kuurne

Phone: +32 56.36.89.70

Fax: +32 56.36.88.24

E-mail: events@barco.com

Visit us at the web: www.barco.com

Printed in Belgium

be recorded, transmitted or stored in a retrieval system without the prior written consent of BARCO.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights

of their respective holders. All brand and product names mentioned in this manual serve as comments or

examples and are not to be understood as advertising for the products or their manufactures.

Federal Communication Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a commercial environment. This equipment generates, uses, and c

an

radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this equipment in a residential area may

cause harmful interference, in which case the user will be responsible for correcting any interference.

Table of contents

TABLE OF CONTENTS

1. Safety ..................................................................................................3

1.1ImportantSafetyInstructions....................................................................................3

1.2ImportantWarnings...............................................................................................4

2. Introduction ..........................................................................................7

2.1Generalfunctionality..............................................................................................7

2.2Specifications......................................................................................................7

2.3OrderinfoEventsController.....................................................................................8

3. Set up ofthe Events Controller..................................................................9

3.1Physicalsetup....................................................................................................9

3.2Monitorssetup...................................................................................................10

3.3Mountingtheharddisks.........................................................................................11

3.4Connectingthemonitors,mouseandkeyboard..............................................................12

3.5Powerconnection................................................................................................16

4. Events Controller checkupprocedure......................................................19

4.1Introduction.......................................................................................................19

4.2Preparationofthecables........................................................................................19

4.3Connectionsforcheckup.......................................................................................21

4.4Testing.............................................................................................................21

4.4.1Startupandadjustments..................................................................................22

4.4.2Runningthetest............................................................................................24

4.4.3Testreportevaluation......................................................................................24

5. Factory fitted connections......................................................................27

5.1InternalPowerconnections.....................................................................................28

5.2Networkconnections ............................................................................................29

5.3InternalSignalConnections.....................................................................................30

6. Connection po ssibilities to the external world ............................................31

6.1Overviewofconnectors .........................................................................................31

Index ....................................................................................................33

R5976619 BARCO EVENTS CONTROLLER 15052003 1

Table of conte nts

2 R5976619 BARCO EVENTS CONTROLLER 15052003

1. Safety

1. SAFETY

1.1 Impor tan t Safety Instru ctions

Instructions:

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do NOT submerge fully or partly in water or other liquids.

• Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking.

Consult themanufacturer for further advice should any doubts exist regarding any cleaningprocedure.

• Do not block ventilation openings. Install in accordance with the manufacturers instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided

sockets / plugs are damaged thenreplacement of the defective parts must be undertak

en immediately.

• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience re-

ceptacles, and the point where they exit from the apparatus. Replace damaged power/data cords

immediately.

• Only use attachments/accessories specified by the manufacturer.

• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning

protection. Unplug this apparatus when unused for long period of time.

• Refer allservicingtoqualified service technicians/personnel. Servicing isrequiredwhen the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, the apparatus does

not operate normally, or has been dropped.

• Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use

caution during lifting/moving or transporting to avoid damage by possible tipping.

R5976619 BARCO EVENTS CONTROLLER 15052003

3

1. Safety

1.2 Important Warnings

Important Warnings:

• Risk of electric shock:

Image 1-1

Risk of electrical shock

Risk of electric shock. Do not open. To reduce the risk of electric shock, do not remove cover (or

back). No user-serviceable parts inside. Refer servicing to qualified service personnel.

The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this

product may cause a risk of electrical shock to persons.

The exclamation point within a triangle is intended to tell the user that important operating and/or

servicing instructions are included in the technical documentation for this equipment.

• Maximum ambient temperature:

The maximum recommended ambient temperature for this equipment is 40

C.

• Flammable materials:

Keep flammable materials away from the installation (such as curtains). A lot of energy is transferred

into heat. The installation should be such that the amount of air flow required for safe operation of the

equipment is not compromised. Proper ventilation must be provided.

• This equipment MUST be earthed:

In order to protect against risk of electric shock, the in

stallation should be properly grounded. Defeat-

ing the purpose of the grounding type plug will expose you to the risk of electric shock. This apparatus

must be grounded (earthed) via the supplied 3 conductor AC power cord. (If the supplied power cord

is not the correct variant, consult your dealer.)

• Power system:

It is recommended to use a TN-S power distribution system (a power distribution system with a sep-

arate neutral and grounding conductor) in order to avoid large ground currents loops due to voltage

differences in the neutral conductor. The total electrical installation should be protected by an appro-

priate rated disconnect switch, circuit breakers and Ground Fault Current Interrupters. The installation

shall be done according to the local electrical installation codes. In Europe special attention should be

given to EN 60364, the standard for electrical installation of buildings. In Germany VDE 0100 should

be adhered to.

• Mains cords:

The power cords delivered with this system have special properties for safety. They are not user

serviceable. If the power cords are damaged, replace only with new ones. Never try to repair a power

cord.

4

R5976619 BARCO EVENTS CONTROLLER 15052003

1. Safety

• Use of an extension cord:

If an extension cord is used with this product, make sure that the total of the ampere ratings on the

products plugged into the extension cord does not exceed the extension cord ampere rating. Also

make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.

• Cabinet openings:

Never push objects of any kind into this product through cabinet slots as they may touch dangerous

high voltage points or short out parts that could result in a risk of fire or electrical shock.

Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet,

unplug the set and have it checked by qualified service personnel before resuming operations.

R5976619 BARCO EVENTS CONTROLLER 15052003

5

1. Safety

6 R5976619 BARCO EVENTS CONTROLLER 15052003

2. Introduction

2. INTRODUCTION

Overview

• General functionality

• Specifications

• Order info Events Controller

2.1 General function ality

Overview

A fully integrated show control system basedon Barco’s D320 platform, the Events Controller enables the

control of all Daylight and Projection Displays as well as all other equipment on your show. This includes

the Catalyst System™, automated and conventional lighting devices, smoke machines, image generators,

truss motors, hydraulics and much, much more. A state-of-the-art show control system, Barco’s Events

Controller provides full image processing and system control. Besides all D320 features, it also brings

unique added features like ’Positracking™’, the ability to recreate the exact position and status of all show

devices as seen at any specific point during the performance. The Events Controller is giving you total

control over every split second of the show.

2.2 Specifications

Overview

Type Value

Internal Components Events Controller

unit

1 unit ViewScape standard

Room for up to 6 D320 units or 3 ViewScape units

Stowable User Console

Optional Fiberlink

Controls Daylight Displays

Projectors

Catalyst™

Lighting devices

Smoke machines

Image Generators

Mechanics/Hydraulics

Supported protocols Barco Daylight Display Protocol

DMX512

MIDI

RS422

RS232

TCP/IP

R5976619 BARCO EVENTS CONTROLLER 15052003 7

2. Introduction

Type Value

Image effects Anamorphic imaging

Chroma-keying [per input]

Alpha-keying [per input]

Z-order control

Windowing

Size flightcase 465,3mm x 740mm x 550mm

Weight ± 30 kg (standard configuration)

Power Power 400W max (standard configuration) auto ranging

90-264V (50-60 Hz)

Connector: 3pin IEC

2.3 Order info Even ts Controller

Order info

Article No. Description

R9851480 Events Controller

FiberLink R9850190

ViewScape R9851590

D320 PL R9851550

D320 Lite R9851560

D320 L R9850710

Digitizer DVI input module R9850960

Digitizer SDI input module R9850970

Digitizer HDSDI input module R9850980

Digitizer CVBS/ S-VID input module R9850920

Digitizer YUV / RG(s)B input module R9850940

Digitizer RGB analog SXGA input R9850950

Digitizer RGB analog UXGA input R9851710

Digitizer dummy input R9850930

8 R5976619 BARCO EVENTS CONTROLLER 15052003

3.SetupoftheEventsController

3. SET U P OF THE EVENTS CONTROLLER

Overview

• Physical set up

• Monitors set up

• Mounting the hard disks

• Connecting the monitors, mouse and keyboard

• Power connection

3.1 Physical set up

How t o set up

1. Put the flight case on its smallest side, on the support bars.

2. Open the locks of the front and back cover. (image 3-1, image 3-2)

3. Take off both covers. (image 3-3)

Image 3-1

Opening the locks of the flight case

R5976619 BARCO EVENTS CONTROLLER 15052003 9

3.SetupoftheEventsController

Image 3-2

Image 3-3

Covers open

3.2 Monitors set up

How t o set up

1. Open the drawer by the handle. (image 3-4, image 3-5)

2. Slide out each monitor and place it on top of the Events Controller. (image 3-6)

3. Take off the protection foil.

Image 3-4

Open drawer

Image 3-5

Drawer open

10 R5976619 BARCO EVENTS CONTROLLER 15052003

3.SetupoftheEventsController

Image 3-6

Monitor o n top of flight case

3.3 Mounting the hard disks

Never transport the Events Controller with the hard disks mounted inside the c ontroller

box as they can be damaged.

How to mount

1. Open the hard disk cover door of the controller box.

2. Take out the disk out of the drawer by pulling on the handle. (image 3-7)

3. Look for an indication ’Master’ or ’Slave’ in one of the corners of the hard disk module.

4. Insert the hard disk in to the controller box and push until it fits into it’s socket. (image 3-8)

Depending on the indication on the hard disk module:

With ’Master’

indicat

ion

Insert in upper position in the controller box

With ’Slave’

indication

Insert in lower position in the controller box

5. Insert the hard disk key which is mounted in the drawer and turn it to the right to activate the hard disk.

The handle of the hard disk will be turned towards the hard disk body.

6. Remove the key and place it back into the drawer.

R5976619 BARCO EVENTS CONTROLLER 15052003

11

3.SetupoftheEventsController

Image 3-7

Hard disk location

Image 3-8

Hard disk insertion

Do not forget to activate the hard disk with the hard disk keys.

3.4 Connect ing the monitors, mouse and keyboard

Where to find

1. Open the storage area in the removed front cover.

See image 3-9.

The following parts are available:

Part description

Quantit

y

Order nu

mber

Mouse 1 V3220707

Keyboard querty 1 B557945

USB monitor cable 2

Monitor-computer cable 2

12 R5976619 BARCO EVENTS CONTROLLER 15052003

3.SetupoftheEventsController

Image 3-9

Peripherals C ontroller Box

How to connect the monitors

1. Take the monitor-to-computer cable (cable with blue sockets) and plug one side into the connector of

the left monitor (A). (image 3-10)

2. Plug the other end into the left monitor connector of the breakout frame.

3. Take the USB monitor cable (those situated above the keyboard) and plug one end into the left monitor

(B) (image 3-10).

4. Plug the other end into the left USB input of the breakout frame.

5. Take the monitor-to-computer cable (cable with blue sockets) and plug one side into the connector of

the right monitor (A) (image 3-10).

6. Plug the other end into the right monitor connector of the breakout frame.

7. Take the USB monitor cable (those situated above the keyboard) and plugone end into the right monitor

(B) (image 3-10).

8. Plug the other end into the right USB input of the breakout frame.

R5976619 BARCO EVENTS CONTROLLER 15052003

13

3.SetupoftheEventsController

Image 3-10

Monitor connection

How to connect the mouse and t he keyboard

1. Plug the mouse cord into the mouse connector on the breakout frame. (image 3-11)

2. Plug the keyboard cord into the keyboard connector on the breakout frame.

14

R5976619 BARCO EVENTS CONTROLLER 15052003

3.SetupoftheEventsController

Image 3-11

Mouse & keyboard connection

R5976619 BARCO EVENTS CONTROLLER 15052003 15

3.SetupoftheEventsController

3.5 Powe r co nnection

Delivered power cables

• One European power cable with wire colors:

- Green/yellow : ground

- Blue : neutral

- Brown : line (live)

Image 3-12

European powe r cable

• One American power cable with wire colors:

- Green/yellow : ground

- White : neutral

- black : line (live)

Image 3-13

American power cable

16 R5976619 BARCO EVENTS CONTROLLER 15052003

Page is loading ...

Barco Events Controller Installation guide

Barco Events Controller Installation guide

Related papers

Other documents