Posiflex TM-6100 User manual

Brand: Posiflex

Model: TM-6100

Category: Touch screen monitors

Type: User manual

Posiflex TM-6100 is a stable touch monitor designed for industrial and commercial use. It features a 12.1” TFT LCD panel with scaling function for full screen display. The resistive touch panel has an extra long life and is resistant to spills. The touch functions include left/right button emulation, double click, drag & drop. The touch beep can be pitch adjusted and enabled/disabled by software control.

19620900020

TM6100 Series

Touch Monitor

USER’S MANUAL

Rev. : Original

I. FEATURES

• Most stable touch monitor for industrial and commercial use

• Application covers POS, POI (Kiosk), Factory Automation etc.

• High quality 12.1” TFT LCD panel with scaling function for full screen display

• Resistive type extra long life touch panel

• Tilt adjustable yet robust and wobble free construction

• Spill proof and easy maintenance structure allowing easy cleaning

• Touch functions include left/right button, double click, drag & drop

• Touch beep can be pitch adjusted and enabled/disabled by software control

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to

comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to

provide reasonable protection against interference when operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to

take whatever measures to correct the interference.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person other than the authorized

technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow

the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or

hazard caused by improper application.

ABOUT THIS MANUAL

This manual assists the user to utilize the TOUCH Monitor TM6000 series. These series provide versatile font

formats and support various instruction sets. These series of products receive instructions in serial communication

protocols and is capable of entering pass through mode so that all instructions received pass on to next connected serial

device if properly configured.

The manufacturer of the TM6000 series heartily apologizes to the user for reserving the right to change or to

modify this manual without notice due to the rapid and constant progress and improvement on science and technology.

The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com.tw,

http: //www.posiflexuk.com, http://www.posiflexusa.com.

 Copyright Mustek Corp. 2003

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Mustek Corp..

Other brand and product names are trademarks and registered trademarks and service marks of their respective

owners.

II. MODEL NUMBER

TM6112: 12.1” LCD Touch Monitor on adjustable stand

TM6101: 12.1” LCD Touch Monitor w/ joining mechanism for Posiflex

touch terminals such as TP-7000 series

III. CARTON CONTENTS

1. Touch Monitor (Main unit assembled with Stand or Joint base)

2. Posiflex Product Information CDROM

3. User’s Manual

4. Power Adaptor: ASP0P042WTB001 &

power cord (for TM6112)

5. VGA Cable: 20867244100 (for TM6112)

or 20863241710 (for TM6101)

6. Touch Control Cable: 20863244210 (for

TM6112) or 20863244200 (for TM6101)

7. Harness for TM6101 to assemble onto TP7000

(separately described in later chapter)

IV. PARTS IDENTIFICATION

A. FRONT VIEW

Display Screen + Touch Panel

Power/Stand By LED

B. SIDE VIEWS

C. INPUT / OUTPUT PORT

D. LED INDICATION

• Green: standby

• Blue: power on

TM6112

Tilt Adjust Button

TP7000 Main Unit

Power on/off Switch

& OSD Buttons

TM6101

VGA Port

Touch Control Port

Power o

n/off Switch

& OSD Buttons

V. INSTALLATION

A. For TM6112

1. Find in the rear of the panel a 10 pin RJ-45 jack for touch controller

connection and a VGA connector.

2. Connect the 10 pin RJ45 plug end of the touch control cable to the jack till it

clicks. Connect and screw fix the end with power connector of VGA cable as

in the picture.

3. Connect and screw fix the other end of touch control cable to an appropriate

COM port and the VGA cable to VGA port of the host system.

4. Check the specification of the power adaptor against the power socket then

insert the power adaptor into the power socket.

Connect the output plug from the power adaptor to

the connector in VGA cable

5. Press in the adjust button when turning the LCD

panel for best viewing effect in application.

B. For TM6101

1. First remove the rear connect cover from the

TP7000 series base stand. Please refer to TP7000

User’s Manual and hold

your thumb gently on the

outer surface of the rear

connect cover while

having your middle finger

inside the stand assembly through the cable

exit to pull the plastic hook plate of the rear

Adjust Button

Touch

Control

VGA

Plug from Adaptor

Power Connector

Back of TM6112

One end of VGA cable

Cables connected

Rear side of TP7000 base

Rear connect cover removed

connect cover from inside to remove the cover.

2. Unlike other rear mount upgrade kit

for TP7000 series, TM6101 requires

some extra operations. First of all,

please check all installation parts

involved. There are 2 supporting

brackets (A and B in the picture), 1

bridging bracket (C in the picture), 16

screws with split washers (D in the

picture) besides the TM6101 on joining mechanism (E in the picture) and 2

interface cables (F and G in the picture).

3. Please then check the bottom

of the TP7000 base stand that

there are 6 screw holes near

the rear mount area as pointed

from circle marks in the

picture.

4. Check the supporting brackets that come in symmetrical pair for the 3 holes

each as pointed from circle marks in the below left picture for screw. Match

these screw holes from bottom of TP7000 series and apply 6 screws to fix

this pair of supporting brackets. Picture to the right shows bottom view of

assembled supporting brackets on TP7000 series.

5. Please then prepare to mount the bridging

bracket (C in the picture) in between the

supporting brackets (A and B). (We mark in the

pictures from now on the base of TP7000 series

as H in white letter for easier understanding.)

Rear bottom of TP7000

A B

F G

Right

Left

Supporting brackets

A B

Install brackets from bottom

A B

6. Screw from both sides through supporting brackets (A and B) and from top

onto the rear connect opening of TP7000 series as pointed by arrows in the

pictures.

7. Connect the 10 pin RJ45 plug end of the touch

control cable to the jack in the rear of the panel

till it clicks. Connect and screw fix the VGA

cable as well.

8. Route both cables to enter TP7000 series through the

opening as in the picture to the right. Connect them to

the appropriate COM port and VGA port of TP7000

series per instructions for TP7000 series. Please

remember to ask a qualified technician to enable the

power supply in the VGA port according to Posiflex

technical instruction but please do not enable power

in the COM port.

9. Join TM6101 (E) onto

brackets on TP7000 (H)

to become the picture

to the right.

10. Fix the final 4 screws

as pointed by arrows in

the picture to the right.

Touch

Control

VGA

11. Press in the tilt adjust button as in picture to the

right when turning the LCD panel for best viewing

effect in application.

VI. DRIVER INSTALLATION

A. INSTALLATION

Please find in the attached Posiflex product information CDROM under

subdirectory \Drivers\TM4_TM6\RS232 or \Drivers\TM4000\RS232 for RS232

interface touch controller driver. In case this subdirectory is not found in the

CDROM received, please use identical driver from relevant product such as

\Drivers\TP6000\Touch\RS232. In such subdirectory, please then find the proper

descendant for the OS applied such as \RSTC_W9x for Win9x system. Click

SETUP.EXE to install the driver into system and a utility program for touch

calibration. Please select “SmartSet Serial Controller” as the controller type

during the installation process. Same approach applies for other operating

system.

If, for any reason, the user wants to remove the driver for the RS232 touch

controller, please select “Monitor Mouse” in the program list for removal.

B. SETUP/CALIBRATION

Once the RS232 touch controller driver is installed, the user can utilize it

to calibrate the touch screen, define mouse button emulation modes, enable right

button emulation or define the click sound’s tone and duration. Please go to

“Control Panel” and select “Elo Touchscreen” to engage this utility. Most items

in this utility should be easily understandable to average user. Followings are

just some reminders on some items.

Ÿ COM port – This port selection must match exactly the port touch

control interface cable is connected to.

Tilt Adjust

Button

Ÿ Align – This function engages 3 touch targets at left top, right bottom

and right top consecutively for touch calibration.

Ÿ Click on touch – This selection of touch button disables the double

click function of a touch and a left click will be registered at the point

where a touch on the screen is made even if the touch is dragged to

other spot before release.

Ÿ Click on release – This selection of touch button disables the double

click function of a touch and a left click will be registered at the point

where a touch is released from the screen.

Ÿ Drag – This selection of touch button disables the double click

function of a touch and a left click contact signal will be sent to the

host when a touch is made and a left click release signal will be there

for touch release.

Ÿ Drag, Double click – This selection of touch button allows the screen

touch to simulate the complete left button of a mouse.

Ÿ Double click size – This adjustment (10 to 100 pixels) is available

only when double click function of the touch is enabled. The larger the

size is, the easier it is to take 2 consecutive taps on the touch screen at

nearly same spot as double click.

Ÿ Show right-click sticky button – This function is only applicable in

Win98 environment. When this box is checked, there will be a large

icon on desktop simulating a mouse. After clicking the right button of

the mouse in this icon, next touch on the screen will act like clicking

the right button of a mouse. After this touch, it will automatically

resume the left click function.

C. APPLICATION

With this touch controller driver, certain display mode like full screen

display of Windows DOS box should be avoided.

VII. POWER & OSD

A. OSD buttons

“OSD” button: To enter OSD setup menu, or to perform function selected

in OSD operation.

“NXT” button: To go to next option function.

“” “” button: To increase setting.

“” “” button: To decrease setting.

“” “” button: To turn the monitor power ON/OFF. The monitor can be

turned OFF only when there is video signal and can be turned ON only

when there is video signal and after the “Turn Off Panel” message

vanishes. The default status is set to ON when power is supplied unless

manually turned OFF. Since this button controls only the display power

but not the display controller neither the touch controller, please try

disconnect the power cable or the VGA cable once unfortunately the

screen display goes into a mess. Please also avoid touching the screen

with the system still running though this power switch is turned off.

B. OSD functions

Press “OSD” button with a normal display on the screen to activate the

OSD functions (On Screen Display adjustment). The OSD window will pop up

on the screen. On top part of this window is a Posiflex logo with the OSD

firmware version indicated to its lower right. Below this area is a row of icons

for main OSD menu. Below the main menu is a group of icons for submenu that

corresponds to one icon selected in the main menu. An analysis of the video

signal on resolution and refresh rate will be displayed at the bottom. Applicable

icons in the main menu and its subsequent menus are explained below.

“MAIN MENU”: There are in total 5 icons in this menu: One of the 5

icons will be displayed in inverted color to indicate its

relationship with the submenu below. Pressing “NXT” button will shift the

selected icon one by one from left to right and then wrap around to the most left.

Press “OSD” button to enter the selected sub menu. If there is no button for OSD

setting is pressed within a period of time (about 5 seconds to 1 minute as

programmed) the OSD window will disappear with all the adjusted parameters

saved. Explanations on items in sub menu are as below.

“BRIGHTNESS / CONTRAST ADJUST SUBMENU”: There are 3

icons in this submenu: Press “OSD” button to select item or return to

main menu. Press “NXT” button to select among brightness, contrast and exit.

“BRIGHTNESS ADJUST”: When this item is selected, there will

be only the brightness icon with an adjustment indication bar under it

between the main menu area and the video signal mode. Press “+” button

to increase brightness. Press “-” to decrease. Press “OSD” button to save

the current setting and return to “Brightness/Contrast submenu”.

“CONTRAST ADJUST”: When this item is selected, there will be

only the contrast icon with an adjustment indication bar under it between

the main menu area and the video signal mode. Press “+” button to

increase contrast. Press “-” to decrease. Press “OSD” button to save the

current setting and return to “Brightness/Contrast submenu”.

“EXIT”: Return to “Main menu”.

“COLOR ADJUST SUBMENU”: There are 4 icons in this submenu:

Press “OSD” button to select item or return to main menu. Press

“NXT” button to select among auto color adjust, auto RGB reset, Color balance

adjust and exit.

“AUTO COLOR ADJUST”: Upon an “OSD” button press on this

icon the monitor will perform an automatic color adjustment and exits the

OSD window leaving 2 icons below at center of the screen. Press “NXT”

button to switch the selection. Press “OSD” button to make the choice.

“ACCEPT”: Accept the adjustment setting.

“REJECT”: Decline the adjustment setting and return to

previous setting.

“AUTO RGB RESET”: Upon an “OSD” button press on this icon

the monitor will perform an automatic RGB reset and exits the OSD

window leaving 2 icons below at center of the screen. Press “NXT” button

to switch the selection. Press “OSD” button to make the choice.

“ACCEPT”: Accept the reset result.

“REJECT”: Decline the reset and return to previous setting.

“COLOR BALANCE ADJUST”: When this item is selected, there

will be 7 icons in this item: between main menu

area and the video signal mode. Press “OSD” button to select an item or

return to color adjust submenu. Press “NXT” button to select among

separate color adjust, 4200K, 5000K, 6500K, 7500K, 9300K and exit.

“SEPARATE COLOR ADJUST”: When this item is

selected, there will be 3 adjustment indication bars between the main

menu area and the video signal mode. Press “NXT” button to select

among the 3 colors Red, Green and Blue respectively. Press “+”

button to intensify that color. Press “-” to reduce. Press “OSD”

button to save the current setting and return to “Color balance adjust

submenu”.

“4200K”: Pressing “OSD” button on this icon will set the

color balance to a color temperature of 4200 degrees Kelvin.

“5000K”: Pressing “OSD” button on this icon will set the

color balance to a color temperature of 5000 degrees Kelvin.

“6500K”: Pressing “OSD” button on this icon will set the

color balance to a color temperature of 6500 degrees Kelvin.

“7500K”: Pressing “OSD” button on this icon will set the

color balance to a color temperature of 7500 degrees Kelvin.

“9300K”: Pressing “OSD” button on this icon will set the

color balance to a color temperature of 9300 degrees Kelvin.

“EXIT”: Return to “Color adjust submenu”.

“EXIT”: Return to “Main menu”.

“GEOMETRY ADJUST SUBMENU”: There are 6 icons in this

submenu: Press “OSD” button to select item or return to

main menu. Press “NXT” button to select among auto geometry adjust,

horizontal size, phase, horizontal position, vertical position and exit.

“AUTO GEOMETRY ADJUST”: Upon an “OSD” button press on

this icon the monitor will perform an automatic geometry adjustment and

exits the OSD window leaving 2 icons below at center of the screen. Press

“NXT” button to switch the selection. Press “OSD” button to make the

choice.

“ACCEPT”: Accept the adjustment setting.

“REJECT”: Decline the adjustment setting and return to

previous setting.

“HORIZONTAL SIZE”: When this item is selected, there will be

only the horizontal size icon with an adjustment indication bar under it

between the main menu area and the video signal mode. Press “+” button

to increase horizontal size. Press “-” to decrease. Press “OSD” button to

save the current setting and return to “Geometry adjust submenu”.

“PHASE”: When this item is selected, there will be only the phase

adjust icon with an adjustment indication bar under it between the main

menu area and the video signal mode. Press “+” or “-” button to adjust the

pixel synchronization phase for best picture display. Press “OSD” button

to save the current setting and return to “Geometry adjust submenu”.

“HORIZONTAL POSITION”: When this item is selected, there

will be only the horizontal position icon with an adjustment indication bar

under it between the main menu area and the video signal mode. Press “+”

or “-” button to shift the screen display to right or left. Press “OSD” button

to save the current setting and return to “Geometry adjust submenu”.

“VERTICAL POSITION”: When this item is selected, there will

be only the vertical position icon with an adjustment indication bar under it

between the main menu area and the video signal mode. Press “+” button

to shift up the screen display. Press “-” to shift down. Press “OSD” button

to save the current setting and return to “Geometry adjust submenu”.

“EXIT”: Return to “Main menu”.

“TOOLS SUBMENU”: When this item is selected, there are 5 icons in

this submenu: Press “OSD” button to select item or return to

main menu. Press “NXT” button to select among OSD submenu, reset to default,

phase, smoothness / sharpness adjust, mode select and exit.

“OSD SUBMENU”: When this item is selected, there are 4 icons in

this submenu: Press “OSD” button to select item or return to

main menu. Press “NXT” button to select among OSD time, OSD

horizontal position, OSD vertical position and exit.

“OSD TIME”: When this item is selected, there will be only

the OSD time icon with an adjustment indication bar under it

between the main menu area and the video signal mode. Press “+” or

“-” button to adjust the waiting time for OSD operation before OSD

termination between 5 to 60 seconds. Default is 30 seconds. Press

“OSD” button to save the current setting and return to “OSD

submenu”.

“OSD HORIZONTAL POSITION”: When this item is

selected, there will be only the vertical position icon with an

adjustment indication bar under it between the main menu area and

the video signal mode. Press “+” button to shift OSD window right.

Press “-” to shift left. Press “OSD” button to save the current setting

and return to “OSD submenu”.

“OSD VERTICAL POSITION”: When this item is selected,

there will be only the vertical position icon with an adjustment

indication bar under it between the main menu area and the video

signal mode. Press “+” button to move OSD window downward.

Press “-” to go upward. Press “OSD” button to save the current

setting and return to “OSD submenu”.

“EXIT”: Return to “Tools submenu”.

“RESET TO DEFAULT”: Pressing “OSD” button on this icon will

set all parameters back to the status when the monitor left factory.

“SMOOTHNESS / SHARPNESS ADJUST”: When this item is

selected, there will be only the smoothness / sharpness adjust icon with an

adjustment indication bar under it between the main menu area and the

video signal mode. Press “+” button to increase smoothness of display

(decrease sharpness). Press “-” to go the other way. Press “OSD” button to

save the current setting and return to “OSD submenu”.

“MODE SELECT”: Pressing “OSD” button on this icon will have

no effect at all if the display mode is not one of the confusing modes. The

confusing modes here mean 640 x 400 or 720 x 400 in display resolution

as both mode have refresh rate of 70Hz, horizontal frequency of 37.9KHz

and pixel frequency of 31.5MHz making it impossible for automatic select.

These modes are not used in normal Windows display.

“EXIT”: Return to “Main menu”.

“EXIT”: Exit OSD setup with all adjustment saved.

VIII. SUPPORTED DISPLAY MODES

For video signals beyond the supported display modes, there will be a

message “Out Of Range” on middle of screen. Maximum supported color depth

is 18 bits or 262,144 colors. Supported display modes are as in the table:

Display Resolution Refresh Rate (Hz) Horizontal Frequency (KHz)

640*400 70 37.9

60 31.5

72 37.9

640*480

75 37.5

720*400 70 37.9

56 35.1

60 37.9

72 48.1

800*600

75 46.9

60 48.4

70 56.5

1024*768

75 60

Posiflex TM-6100 User manual

Brand: Posiflex

Model: TM-6100

Category: Touch screen monitors

Type: User manual

Download PDF

report

Posiflex TM-6100 User manual

Posiflex TM-6100 User manual

Related papers

Other documents