Hitachi DS55MU01 User manual

DS65MU01

User Manual (English)

DS65MU01

iii

1. Important Safety instructions

[SAFETY WARNING]

• To reduce the risk of re or electric shock, do not expose this product to rain or moisture.

• To prevent injury, this product must be securely attached to the oor/wall in accordance with the installation

instructions.

• To reduce the risk of electric shock, do not remove the back cover

• Refer to qualied service personnel if needed.

Icons used in this manual

[WARNING] means,

If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.

[CAUTION] means,

If you ignore the caution message, you may be slightly injured or the product may be damaged.

[NOTE] means,

The note helps you understand and use the product safely. Please read the note carefully before using the product.

Warning:

This equipment is compliant with Class A of EN55032/CISPR 32. In a residential environment this equipment may cause

radio interference.

When moving the product, please grab the handles behind and the bottom of the product as shown below picture.

• The product must keep horizontal and upright position when moving.

• Do not hold the corner of the product when you grab the bottom of the product.

DS65MU01

iv

1.1. SAFETY PRECAUTION

Note: The color and design may different by each model and the product specication are subject to change without

notice for performance enhancement.

1.1.1. Power

[Warning]

• Do not use damaged power cord, plug nor loose socket. It may cause electric shock or re.

• Do not connect multiple devices into a single socket. It may cause re due to overheating.

• Do not touch with wet hands when remove or plug the power cord to avoid electric shock.

• Insert the power plug into socket rmly. It may cause re when the connections are unstable.

• Connect the power cord to a grounded wall socket. There is risk of electric shock or injury.

• Do not bend nor pull the power cord and place heavy objects over the power cord. It may occur cord damage

and this may result in re.

• Please clean only with dry cloth when the plug pin or socket are dusty. It may cause re.

[Caution]

• Do not unplug the power plug while the product is operating. It may damage the product due to electric shock.

• Only a power cord specied by product manufacturer are recommended.

• Do not use the power cord from other devices. It may cause electric shock or re.

• Hold the plug itself when unplugging the power plug from the wall socket. If not, there is risk of electric shock or

re.

• Before moving or installing this product, be sure to turn off the power and disconnect the power cord. To turn

this product off completely, you must pull the power plug out of the wall socket. Consequently, the power plug

must be easily and readily accessible at all times.

• The AC inlet and MAIN Power Switch are disconnect device, the location on the apparatus and the function of

the switch shall be described, and the switch shall remain readily operable

.

1.1.2. Installation

[Warning]

• Do not install near any heat sources such as radiators, or other devices that produce heat. It may cause electric

shock or re.

• When mounting a product on the wall, make sure not to install the product by hanging the power and signal

cables on the back of it.

• Consult with your local dealer or specialized engineer to mount the product on the wall, and use the screws and

wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are

not covered by the warranty.

• Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. If not, it may cause re.

• Keep the packing anti-moisture material or vinyl packing out of the reach of children. Anti-moisture material is

harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally,

vinyl packing can cause suffocation. Keep it out of the reach of children.

• Please note than the product must be supported on proper stands or installed according to the manufacturer’s

recommendations. The product that are inappropriately situated on unstable shelves, inclined planes, or vibrating

places, etc., may fall over, resulting in injury.

• To reduce the risk of re or electrical shock, do not expose this product to rain, moisture or other liquids or dust.

It may cause electric shock or re.

• Keep the product away from direct sunlight.

• Keep the product of the reach of children and install on the stable and at place. NEVER allow children to climb

on or play on the product or the furniture and stands on which the product is placed.

DS65MU01

v

[Caution]

• Do not allow an impact shock or any objects to fall into the product, and do not drop anything onto the screen.

• Make sure the product is turned off, unplugged, and all cables have been removed. It may take more than 4 people

to than carry.

• Do not press or put stress on the front panel of the product.

• If the product is installed in a place where the operating conditions considerably, a serious quality problem may

occur due to the surrounding environment. In this case, install the product only after consulting our dealer about

the matter. (Places exposed to microscopic dust, chemicals, too high or low temperature, high humidity, airports or

stations where the product is continuously used.)

1.1.3. Cleaning

[Warning]

• Before cleaning the product, unplug the power cord and wipe gently with a soft cloth to prevent scratching.

• Do not spray water or other liquids directly on the product as electric shock may occur.

[Caution]

• Do not push, rub, or hit the surface with your ngernail or a sharp object, as this may result in scratches on the

screen and image distortions.

• Do not use any chemicals, such as waxes, benzene, alcohol, thinners, insecticides, air fresheners, or lubricants, as

these may damage the screen’s nish and cause discoloration.

• Do not spray liquid onto the surface. If water enters the product, it may result in re, electric shock, or malfunction.

1.1.4. General Usage

[Warning]

• To reduce the risk of electric shock, do not open the cover or back. No user serviceable parts inside. Refer to

qualied service personnel.

• Before moving or lifting the product, disconnect the power cord and all cables.

• The route cords and cables connected to the product so that they cannot be tripped over, pulled or grabbed.

• Do not stick metal objects or any other conductive material into the power cord. Do not touch the end of the

power cord while it is plugged in. It may result in re, electric shock.

• Unplug this product during lightning storms or when unused for long periods of time.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• To reduce the risk of re or electrical shock, do not expose this product to rain, moisture or other liquids. Do not

touch the product with wet hands. Do not install this product near ammable objects such as gasoline or candles,

or expose to direct air conditioning.

• NEVER allow children to climb on or play on the product or the furniture on which it is placed. It may cause

severe injury to children.

• Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the product. When

a cart is used, be careful when moving the cart/product combination to avoid injury from tip-over.

• Install where it cannot be pushed, pulled over or knocked down.

• It is recommended to move the product in the box or packing material that originally came in.

• When holding the product, the screen should face away from you to avoid damage.

[Caution]

• If a xed image displays on the screen for a long period of time, it will be imprinted and become a permanent

disgurement on the screen. This is image burn or burn-in and not covered by the warranty.

• Avoid displaying a xed image on the screen for a long period of time to prevent image burn. Recommend to

power off or set the screen saver mode when not in use. Be aware that the image burn symptom cannot be

repaired and is not covered under warranty.

• When watching the screen, take 5 to 15 minute breaks every hour. Viewing screen for a long period of time may

cause fatigue or eye strain.

DS65MU01

vi

• Take care not to touch the ventilation openings. When watching the screen for a long period, the ventilation

openings may become hot. This does not affect the performance of the product or cause defects in the product.

• Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and

cause it to fall.

• To install batteries in remote control, open the battery cover, replace batteries matching (+) and (-) ends to the

label inside the compartment, and close the battery cover. Failure to match the correct polarities of the battery

may cause the battery to burst or leak, resulting in re, personal injury, or ambient pollution.

• To prevent to swallow the small accessories for children, keep the accessories out of the reach of children.

• The product must keep horizontal and upright position when moving. Hold the top and bottom of the frame

rmly.

• When attaching the wall mount to the set, place the screen facing down on a cushioned table or at surface to

protect the screen from scratches by more than 2 people,

• Make sure that the screws are fastened tightly. (If they are not fastened securely enough, it may tilt forward after

being installed.)

1.2. MAINTENANCE

1.2.1. Cleaning

[Warning]

• When cleaning, unplug the power cord and wipe gently with a soft dry cloth to prevent scratching.

• Do not spray water or other liquids directly on the screen as electric shock may occur.

• Do not clean with chemicals such as alcohol, thinners, or benzene.

1.2.2. Installation

• Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. If not, it may cause re or

malfunction due to the high temperature product inside.

[When mounting on a wall]

10cm (3.93 inches)

10cm

(3.93 inches)

10cm

(3.93 inches)

1.2.3. Panel

• Avoid displaying a xed image on the screen for a long period of time (2 or more hours for LCD) to prevent

image burn. Recommend to power off or set the power saving mode or screen saver when not in use.

• Due to technological constraints of the Panel manufacturer, the images generated by this product may appear

either brighter or darker than normal by appr. 1ppm (parts per million) pixel.

• The number of sub-pixels of a panel by size: The number of Sub-Pixels = Max. Horizontal Resolution x Max.

Vertical Resolution x 3.

• For example, if the maximum resolution is 3840 x 2160, the number of sub-pixels is 1920 x 1080 x 3 =

12,441,600.

DS65MU01

vii

Table Of Contents

1. Unpacking and Installation.................. 1

1.1. Unpacking ...........................................1

1.2. Package Contents ...........................1

1.3. Installation Notes ............................1

1.4. Mounting on a Wall .......................2

2. Parts and Functions............................. 3

2.1. Control Panel ....................................3

2.2. Input/Output Terminals ...............4

2.3. Remote Control ..............................6

3. Connecting External Equipment 9

3.1. Connecting External Equipment

(DVD/VCR/VCD) ..........................9

3.2. Connecting a PC .............................9

3.3. Connecting Audio Equipment 1 0

3.4. Connecting Multiple Displays in

a Daisy-chain Conguration . . 10

3.5. IR connection .................................11

3.6. IR Pass-through Connection . 11

4. Operation............................................ 12

4.1. Watch the Connected Video

Source ................................................12

4.2. Change Picture Format ............ 12

4.3. Overview .........................................12

4.4. Media Player introduction: ......13

4.5. Browser manual ............................14

4.6. PDF reader play ............................16

4.7. CMS .....................................................18

4.8. Custom App ...................................18

5. Signage display..................................... 19

5.1. Setting ................................................19

5.2. Ethernet ............................................19

5.3. Proxy ...................................................20

5.4. Signage Display ..............................20

5.5. System Tools ................................... 28

5.6. Clone Media File ..........................29

5.7. Display ..............................................30

5.8. Apps ....................................................30

5.9. Security ..............................................30

5.10. Date & time ....................................30

5.11. Developer options ......................30

5.12. About .................................................30

5.13. Supplementary ..............................31

6. OSD Menu........................................... 34

6.1. Navigating the OSD Menu.....34

6.2. OSD Menu Overview ..............34

7. Supported Media Formats................ 41

8. Input Mode.......................................... 44

9. Cleaning and Troubleshooting 46

9.1. Cleaning ............................................46

9.2. Troubleshooting ............................47

10. TechnicalSpecications......................49

DS65MU01

1

1. Unpacking and Installation

1.1. Unpacking

• This product is packed in a carton, together with the standard accessories.

• Any other optional accessories will be packed separately.

• Due to the size and weight of this display it is recommended for two people to move it.

• After opening the carton, ensure that the contents are complete and in good condition.

1.2. Package Contents

Please verify that you received the following items with your package content:

• LCD display

• User Manual

• Warranty Card

• Remote control and AAA Batteries

• Power Cord

• RS232 Cable

• RS232 Daisy Chain Cable

• HDMI Cable

* The supplied power cord varies depending on destination.

Power Cord

User Manual

RS232 Daisy Chain Cable

FORMAT

SOURCE

INFOLIST

OPTIONSADJUST

VOL

NORMAL

ID

ID SET ENTER

RS232 Cable

HDMI Cable

Warranty Card

Remote Control

and AAA Batteries

NOTES:

• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been

approved by and complies with the safety regulations of the particular country (Type H05W-F, 2G or 3G, 0.75 or

1 mm

2

should be used).

• You might like to save the package box and packing material for shipping the display.

1.3. Installation Notes

• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line

is required, please consult your service agent.

• The product should be installed on a at surface to avoid tipping. The distance between the back of the product

and the wall should be maintained for proper ventilation. Avoid installing the product in the kitchen, bathroom or

any other places with high humidity so as not to shorten the service life of the electronic components.

• The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some

abnormalities may be experienced.

DS65MU01

2

1.4. Mounting on a Wall

To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We

recommend using a mounting interface that complies with TUV-GS and/or UL1678 standard in North America.

Protective Sheet

VESA Grid

Table

1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen

surface so as not to scratch the screen face.

2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc).

3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could

result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage

caused by improper installation.

4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the

mounting bracket) and tighten them securely.

5. Unit without base weight= 24.8 kg. The equipment and its associated mounting means still remain secure during

the test. For use only with UL Listed Wall Mount Bracket with minimum weight/load: 24.8 kg.

6. Portrait is not allowed.

1.4.1. VESA Grid

DS65MU01 400(H) x 400(V) mm

Caution:

To prevent the display from falling:

• For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially

available. For detailed installation instructions, refer to the guide received with the respective bracket.

• To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other

natural disaster, be sure to consult the bracket manufacturer for installation location.

Ventilation Requirements for enclosure locating

To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.

100 mm 100 mm

100 mm

DS65MU01

3

2. Parts and Functions

2.1. Control Panel

MUTE INPUT

MENU

1 2 3 4 5 6 7 8

9

1

[ ] button

Use this button to turn the display on or put the

display to standby.

2

[MUTE] button

Switch the audio mute ON/OFF.

3

[INPUT] button

Choose the input source.

4

[ ] button

• Increase the volume

• Enter into submenu while OSD menu is on

5

[ ] button

• Decrease the volume

• Back to previous menu while OSD menu is

on

6

[ ] button

• Move the highlight bar up to adjust the

selected item while OSD menu is on

• Increase the adjustment while adjust value.

7

[ ] button

• Move the highlight bar down to adjust the

selected item while OSD menu is on.

• Decrease the adjustment while adjust value.

8

[MENU] button

Return to previous menu while OSD menu is

on, or to activate the OSD menu when OSD

menu is off.

9

Remote control sensor and power status

indicator

• Receives command signals from the remote

control.

• Indicates the operating status of the display

without OPS:

• Lights green when the display is turned

on

• Lights red when the display is in standby

mode

• When {SCHEDULE} is enabled, the light

blinks green and red

• If the light blinks red, it indicates that a

failure has been detected

• Lights off when the main power of the

display is turned off

* Using IR sensor cable for better remote

control performance. (Please refer to the

instructions of 3.5)

DS65MU01

4

2.2. Input/Output Terminals

HDMI 3 IN HDMI 4 IN

AUDIO IN

MICRO SD

IR-INIR-OUT

AUDIO OUT

USB 5V/0.5A

5V/2A

D-SUB

USB 2.0 5V/0.5A

USB 3.0 5V/0.9A

HDMI 1 IN HDMI 2 IN

DP IN

RJ45

RS232

OUT

RS232

IN

9

10

12

11

13

14

16

15

17

18

19

20

3

4 6

5 7 8

1

2

1

AC IN

AC power input from the wall outlet.

2

MAIN POWER SWITCH

Switch the main power on/off.

3

RJ-45

LAN control function for the use of remote

control signal from control center. and internal

function.

4

RS232C IN /

5

RS232C OUT

RS232C network input / output for the loop-

through function.

6

DisplayPort IN

DisplayPort video input.

7

HDMI1 IN /

8

HDMI2 IN /

9

HDMI3

IN /

10

HDMI4 IN

HDMI video/audio input.

11

IR OUT /

12

IR IN

IR signal input / output for the loop-through

function.

NOTES:

• This display’s remote control sensor will

stop working if the jack [IR IN] is connected.

• To remotely control your A/V device via

this display, refer to page 9 for or IR Pass

Through connection.

13

VGA IN (D-Sub)

VGA video input.

14

AUDIO IN

Audio input for VGA source (3.5mm stereo

phone).

15

AUDIO OUT

Audio output to external AV device.

16

USB PORT

Connect your USB storage device

17

USB PORT A

USB

5V/2A

18

MICRO SD CARD

Connect your MICRO SD CARD.

19

OPS SLOT

Slot for installing the optional OPS module.

20

SECURITY LOCK

Used for security and theft prevention.

DS65MU01

5

2.2.1. Inserting the batteries in the remote control

The remote control is powered by two 1.5V AAA batteries.

To install or replace batteries:

1. Press and then slide the cover to open it.

2. Align the batteries according to the (+) and (–)

indications inside the battery compartment.

3. Replace the cover.

Caution:

The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:

• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery

compartment.

• Do not mix battery types.

• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.

• Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment. Don’t

touch exposed battery acid, as it can damage your skin.

NOTE: If you do not intend to use the remote control for a long period, remove the batteries.

2.2.2. Handling the remote control

• Do not subject to strong shock.

• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry

immediately.

• Avoid exposure to heat and steam.

• Other than to install the batteries, do not open the remote control.

2.2.3. Operating range of the remote control

Point the top of the remote control toward the display’s remote control

sensor when pressing a button.

Use the remote control within a distance of less than 5m/16ft from

the display’s sensor, and a horizontal and vertical angle of less than 30

degrees.

NOTE: The remote control may not function properly when

the remote control sensor on the display is under direct

sunlight or strong illumination, or when there is an obstacle

in the path of signal transmission.

3030

DS65MU01

6

2.3. Remote Control

2.3.1. General functions

1

2

3

4

5

6

7

8

10

9

12

14

15

11

13

16

1

[ ] POWER button

Power ON/OFF.

2

[PLAY] buttons

Control playback of media les.(for Media Input

only)

Freeze feature

Pause: Freeze hot key for all inputs content.

Play: Unfreeze hot key for all input content.

3

[ ] SOURCE button

Root Menu: Go to Video source OSD.

4

[ ] HOME button

Root Menu: Go to Main Menu OSD.

Others: Exit OSD.

5

[ ] LIST button

No function.

6

NAVIGATION buttons

[ ]

Root Menu: Go to Smart picture OSD.

Main Menu: Move the highlight bar up to adjust

the selected item.

IR Daisy Chain Menu: Increase controlled Group

ID number.

[ ]

Root Menu: Go to Audio source OSD.

Main Menu: Move the highlight bar down to adjust

the selected item.

IR Daisy Chain Menu: Decrease controlled Group

ID number.

[ ]

Main Menu: go to previous level menu.

Source Menu: Exit source menu.

Volume Menu: Decrease Audio Volume.

[ ]

Main Menu: go to next level menu or set selected

option.

Source Menu: Go to selected source.

Volume Menu: Increase Audio Volume.

7

[ ] button

Root Menu: Go to IR daisy chain OSD in Primary/

Secondary mode.

Main Menu: Conrm an entry or selection.

8

[ ] ADJUST button

Go to Auto Adjust OSD for VGA only.

9

[ ] MUTE button

Toggle Audio Mute/Unmute.

10

[ ] [ ] [ ] [ ] COLOR

buttons

Choose tasks or options.(for Media Input only)

[ ]

Hot key for Window selection function.

11

[Number/ ID SET/ ENTER] button

Enter text for network setting.

Press to set the display ID. Refer to 2.3.2. ID

Remote Control for more detail.

DS65MU01

7

12

[ ] FORMAT button

Change Image Zoom Mode [Full][4:3][Real]

[21:9][Custom].

13

[

] BACK button

Return to the previous menu page or exit from

the previous function.

14

[ ] INFO button

Show Information OSD

15

[ ] OPTIONS button

No function.

16

[ ] [ ] VOLUME button

Adjust volume.

DS65MU01

8

2.3.2. ID Remote Control

You can set the remote control ID when you want

to use this remote control on one of several different

displays.

Press [ID] button. The red LED blinks twice.

1. Press [ID SET] button for more than 1 second to

enter the ID Mode. The red LED lights up.

Press the [ID SET] button again will exit the ID

Mode. The red LED lights off.

Press the digit numbers [0] ~ [9] to select the display

you want to control.

For example: press [0] and [1] for display No.1, press [1]

and [1] for display No.11.

The numbers available are from [01] ~ [255].

2. Not pressing any button within 10 seconds will exit

the ID Mode.

3. If an error pressing of buttons other than the digits

occured, wait 1 second after the red LED lights

off and then lights up again, then press the correct

digits again.

4. Press [ENTER] button to conrm. The red LED

blinks twice and then lights off.

NOTE:

• Press [NORMAL] button. The green LED blinks

twice, indicating the display is in normal operation.

• It is necessary to set up the ID number for each

display before selecting its ID number.

DS65MU01

9

3. Connecting External Equipment

3.1. Connecting External Equipment (DVD/VCR/VCD)

3.1.1. Using HDMI video input

DVD / VCR / VCD

HDMI 3 IN HDMI 4 IN

IR-INIR-OUT

HDMI 1 IN HDMI 2 IN

HDMI Out

[HDMI IN]

3.2. Connecting a PC

3.2.1. Using VGA input

PC

AUDIO IN

IR-INIR-OUT

AUDIO OUT

D-SUB

[VGA IN]

[VGA AUDIO IN]

VGA Out

D-Sub 15 pin

Audio Out

3.2.2. Using HDMI input

PC

HDMI 3 IN HDMI 4 IN

IR-OUT

HDMI 1 IN HDMI 2 IN

HDMI Out

[HDMI IN]

DS65MU01

10

3.2.3. Using DisplayPort input

PC

DisplayPort Out

[DisplayPort IN]

HDMI 1 IN HDMI 2 IN

DP IN

RS232

OUT

3.3. Connecting Audio Equipment

3.3.1. Connecting an external audio device

Stereo Amplifier

[AUDIO OUT] Audio In

AUDIO OUT

3.4. Connecting Multiple Displays in a Daisy-chain Configuration

You can interconnect multiple displays to create a daisy-chain conguration for applications such as a menu board.

3.4.1. Display control connection

Connect the [RS232 OUT] connector of DISPLAY 1 to the [RS232 IN] connector of DISPLAY 2.

DISPLAY 1

PC

DISPLAY 2

[RS-232C IN]

[RS-232C]

[RS-232C OUT] [RS-232C IN]

DISPLAY 1

PC

DISPLAY 2

[RJ-45] [RS-232C OUT] [RS-232C IN]

[RJ-45]

DS65MU01

11

3.5. IR connection

[IR IN]

External

IR Receiver

[IR IN]

[IR OUT]

DISPLAY 1

DISPLAY 2

DISPLAY 1 DISPLAY 2

[RS-232C OUT] [RS-232C IN]

NOTE:

1. This display’s remote control sensor will stop working if the [IR IN] is connected.

2. IR loop through connection can support up to 9 displays.

3. IR in daisy chain via RS232 connection can support up to 9 displays.

3.6. IR Pass-through Connection

DVD / VCR / VCD

(DVD / VCR / VCD)

Remote Control

[IR OUT]

[IR IN]

DS65MU01

12

4. Operation

NOTE: The control button described in this

section is mainly on the remote control

unless specied otherwise.

4.1. Watch the Connected Video

Source

1. Press

[ ]

SOURCE button.

2. Press

[ ]

or

[ ]

button to choose a device, then

press

[ ]

button.

4.2. Change Picture Format

You can change the picture format to suit the video

source. Each video source has its available picture

formats.

The available picture formats depend on the video

source:

1. Press

[ ]

FORMAT button.

• PC mode: {Full} / {4:3} / {1:1} / {21:9}/

{Custom}.

• Video mode: {Full} / {4:3} / {1:1} / {21:9}/

{Custom}.

4.3. Overview

1. Android PD launcher:

• Android PD launcher is black page, as

below:

• Every apps leave by press back key, the

screen will go to android PD launcher.

• When you return to android PD launcher,

the screen will show hint image, the hint

image only show 5 second, as below:

• The hint image will notify you can press

source key to change source.

2. Admin mode:

• You can press “Home + 1668” to enter

admin mode. Please make sure you see the

Home OSD menu after “Home” is pressed,

and then press 1668 in sequence. Two

continuous “Home” keys will not be a valid

hotkey.

• Admin mode will show four icons:

“Settings”, “Apps”, “Network” and

“Storage”.

• When you leave admin mode, system will

return to last source.

1)Home page of admin mode, this page has

four items: “Settings”, “Apps”, “Network” and

“Storage”.

Settings : go to settings app.

Applications : show all apps.

Network : set Ethernet and Mobile network

(optional).

Storage : display current PD Android storage

information.

2.) Application page:

3

）

Network page

4

）

Ethernet page

DS65MU01

13

4.4. Media Player introduction:

1. Home page of MediaPlayer app, this page has

three items: “Play”, “Compose” and “Settings”.

Play : select playlist to play.

Compose: edit playlist.

Settings: setting play properties.

2. Select “Play” on home page, rst you should

choose one playlist to play between FILE 1 and

FILE 7.

The pencil icon means the playlist is non-empty.

3. Select “Compose” on home page, rst you

should choose one playlist to edit between FILE

1 and FILE 7.

The pencil icon means the playlist is non-empty.

4. If an empty playlist is chosen, the app will guide

you to select the media source.

All media les should be placed in /signage/ of

directory.

For example,

- videos in signage/video/

- photos in signage/photo/

- music in signage/music/

5. You could edit or delete a non-empty playlist, just

choose the desired playlist which is with pencil

icon.

6. Once you start to edit a playlist, you will see

below screen.

Source - les in storage.

Playlist – les in playlist.

There are 4 icons which map to the keys of

remote controller. Option key – launch slide bar

Play key – play media le.

Info key – show media info.

Ok key – select/unselect le.

6-1 In the slide bar, it helps you to do the

following:

- select all : select all storage les.

- delete all : delete all playlist les.

- add/remove : update playlist from source.

- sort : sort playlist.

- save/abort : save or abort playlist.

- back : return.

7. If you choose “Sort” in the slide bar, you can

change the order of les one by one.

Page is loading ...

Hitachi DS55MU01 User manual

This manual is also suitable for

Hitachi DS55MU01 User manual

Related papers

Other documents