iogear GUW101A User manual

1

GUW101A

Installation

Installation Guide

Wireless Audio Receiver

2

3

2

3

Table of Contents

System Requirements 4

Package Contents 5

Device Overview - Wireless Audio Receiver 6

Software Installation - Preparing for Setup 7

Software Installation – For XP users 8

Update/Install Wireless USB Manager 8

Update USB Transmitter 11

Update Wireless VGA Receiver 15

Software Installation – For Vista users 20

Update/Install Wireless USB Manager 20

Update USB Transmitter 23

Update Wireless Video Receiver 28

Hardware Installation 34

Connecting the Audio Receiver to Speakers 38

Advanced Settings – Wireless USB Manager 42

Advanced Settings – Wireless USB

Transmitter Setting

44

Trouble Shooting Guide 46

Technical Specication 60

Appendix 62

Limited Warranty 66

Federal Communications Commission

(FCC) Statement

67

Contact 68

4

5

System Requirements

1 x Wireless USB Transmitter (GUWA200) •

Available 3.5mm or RCA audio input socket on your TV/display or stereo system•

Important Note: Your computer must be Wireless USB ready or has already installed Wireless USB on the

computer before you can use the Wireless Audio Receiver.

4

5

1 x Power adapter •

1 x Quick Start Guide / •

User manual

1 x Installation CD •

1 x Warranty / •

Registration Card

Package Contents

1 x Wireless USB to •

Audio receiver (for stereo)

1 x USB 2.0 A to mini-B cable (3 ft.) •

1 x 3.5mm to 3.5mm cable •

1 x 3.5mm to RCA cable •

6

7

Device Overview - Wireless Audio Receiver

Power/Activity LED 1.

- LED is solid when connection is established

- LED is blinking when power is on and con

nection is not established

3.5mm Audio Socket 2.

- Connects to the 3.5mm audio connector of

the included 3.5mm or RCA audio cable, and

the other end to the available 3.5mm audio

socket or RCA audio socket on your display

or stereo system

Mini-B USB Port 3.

- Connects to the mini-B end of the included

USB cable, and the Type-A end to an avail

able USB port on your computer to create

association between your computer and the

audio receiver

Power plug 4.

- Power adapter socket

1

2

3

4

6

7

Software Installation - Preparing for Setup

This section is only for customers who previously purchased GUW2015VKIT, GUW2015VKITW6 or

GUW2015V. In order to ensure the quality of the performance, this section will guide you through

a series of steps for upgrading the Wireless USB Manager software and the rmware of the USB

Transmitter and the Wireless Video Receiver. Please follow the exact procedures, DO NOT skip or

re-arrange the procedures.

If this is your rst purchase of Wireless USB products and you do not have any GUW2015VKIT,

GUW2015VKITW6 or GUW2015V, then please follow below instructions to complete only the

Update/Install Wireless USB Manager section. Then proceed to page 34 for Hardware Instal-

lation.

8

9

Update/Install Wireless USB Manager

Insert the CD into the CD-ROM of your 1.

computer, and the auto run program will load

the GUW101A Software Installation window.

Click on2. Install Wireless USB Manager to

continue

Click on 3. Yes to continue.

Software Installation – For XP users

8

9

Click on 4. Next to continue.

10

11

Select 5. Yes, I want to restart my computer

now., then click on Finish to restart your

computer.

10

11

Update USB Transmitter

Before you begin, keep the USB Transmitter 1.

plugged into the USB port of your computer.

DO NOT unplug the USB Transmitter from

the USB port, and DO NOT remove the USB

Transmitter from the USB port during software

installation process.

Insert the CD into the CD-ROM of your com-2.

puter, and the auto run program will load the

GUW101A Software Installation window.

Click on 3. Update USB Transmitter to continue.

12

13

When you are prompted with the HWA 4.

Firmware Update Tool general notes, click

and drag the side bar to the bottom and

click on Next to continue.

Click on 5. Next to continue.

12

13

Click on 6. Continue Anyway to continue. Click on 7. Next to continue.

14

15

When prompted by this message, click on 8. OK

to continue.

The rmware updating process is now 9.

completed and it will take up to a minute to

complete the process. Click on Finish to

close the update tool.

14

15

Update Wireless VGA Receiver

Insert the CD into the CD-ROM of your 1.

computer, and the auto run program will

load the GUW101A Software Installation

window.

Click on 2. Update Video Receiver to

continue.

16

17

Follow the instructions on the prompted 3.

window. Plug the mini-B end of the included

USB cable to the mini-B connector on the

Wireless Video Receiver. Plug the type-A

end of the USB cable into an available port

of your computer. Make sure to have the

power adapter connected to the Wireless

Video Receiver and the Wireless Video

Receiver is powered on. Click on Next to

continue.

16

17

Click on 4. OK to continue.

Click on 5. Next to continue.

18

19

Click on 6. Finish to complete the update process.

DO NOT7. disconnect the Wireless Video

Receiver from your computer. Unplug the

power adapter and plug it back into the

Wireless Video Receiver, then click OK to

continue.

18

19

Click 8. OK to continue.

Unplug the power adapter and plug it back 9.

into the Wireless Video Receiver, then click on

OK to complete the update process. Now you

can disconnect the Wireless Video Receiver

from your computer, and keep the power

adapter connected to the Wireless Video

Receiver. All connection should resume normal

automatically.

20

21

Update/Install Wireless USB Manager

Insert the CD into the CD-ROM on your 1.

computer, the auto play program will launch

on its own. Click on Run CD_Start32.exe

or Run CD_Start64.exe (depends on the

version of Vista OS that you are using) to

continue.

Software Installation – For Vista users

Click on 2. Install Wireless USB Manager to

continue.

Page is loading ...

iogear GUW101A User manual

Related papers

Other documents