3M Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP is designed to seal enamel pits and fissures to prevent caries, and bond composite restorations to tooth structure. It contains a self-etching adhesive that eliminates the need for separate etching and bonding steps. The kit includes everything needed for sealing pits and fissures or bonding composite restorations, making it a convenient option for dental professionals.

3M Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP is designed to seal enamel pits and fissures to prevent caries, and bond composite restorations to tooth structure. It contains a self-etching adhesive that eliminates the need for separate etching and bonding steps. The kit includes everything needed for sealing pits and fissures or bonding composite restorations, making it a convenient option for dental professionals.

SEALING PITS AND FISSURES
Clinpro
Sealant
Indications:
• 3M
ESPE
Clinpro
Sealant is designed for sealing the enamel
pits and fissures of teeth to aid in the prevention of caries.
Preparation:
• Select teeth. Teeth must be sufficiently erupted so that a dry
field can be maintained.
• Clean Enamel. Thoroughly clean teeth to remove plaque and
debris from enamel surfaces and fissures. Rinse thoroughly
with water. Note: Do not use any cleaning medium that may
contain oils.
• Isolate teeth and dry. While a rubber dam provides the best
isolation, cotton rolls used in conjunction with isolation shields
are acceptable.
3
1 of 2
Dry Etched Enamel:
Thoroughly dry the etched surfaces.
Air should be oil and water free.
The dry etched surfaces should appear
as a matte frosty white. If not, repeat
steps 1 and 2. Do not allow the etched
surface to be contaminated.
1
2
Etch Enamel:
Using syringe tip, or fiber tip, apply a
generous amount of etchant to all enamel
surfaces to be sealed, extending beyond
the anticipated margin of the sealant.
• Etch for a minimum of 15 seconds, but
no longer than 60 seconds.
Rinse Etched Enamel:
Thoroughly rinse teeth with air/water spray
to remove etchant.
• Do not allow patient to swallow or rinse.
If saliva contacts the etched surfaces, re-
etch for 5 seconds and rinse.
SEALING PITS AND FISSURES
Clinpro
Sealant
2 of 2
3M ESPE Customer Hotline 1-800-634-2249 70-2009-2437-4B
Please refer to instructions for more detailed information 44-0023-3836-4B
as well as precautionary and warranty information. © 2003 3M
3M, ESPE and Clinpro are trademarks of 3M or 3M ESPE AG.
Apply Sealant:
Using the syringe needle tip, or a brush,
apply sealant into the pits and fissures.
Do not let sealant flow beyond the etched
surfaces.
Stirring the sealant with the syringe-tip
during or after placement will help
eliminate any possible bubbles, and
enhance the flow into the pit and fissures.
An explorer may also be used.
Light-Cure:
Cure the sealant by exposing it to light
from a 3M
ESPE
Light-Curing Unit, or
other curing unit of comparable intensity.
A 20-second exposure is needed for each
surface. The tip of the light should be
held as close as possible to the sealant,
without actually touching the sealant.
When set, the sealant forms a hard,
opaque film, light yellow in color with a
slight surface inhibition.
4
5
6
Wipe Clean:
• Wipe the sealant with a cotton applicator
to remove the thin film on the surface.
  • Page 1 1
  • Page 2 2

3M Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP is designed to seal enamel pits and fissures to prevent caries, and bond composite restorations to tooth structure. It contains a self-etching adhesive that eliminates the need for separate etching and bonding steps. The kit includes everything needed for sealing pits and fissures or bonding composite restorations, making it a convenient option for dental professionals.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI