3M Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP User guide

Brand: 3M

Model: Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP

Type: User guide

This manual is also suitable for

3M Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP is designed to seal enamel pits and fissures to prevent caries, and bond composite restorations to tooth structure. It contains a self-etching adhesive that eliminates the need for separate etching and bonding steps. The kit includes everything needed for sealing pits and fissures or bonding composite restorations, making it a convenient option for dental professionals.

SEALING PITS AND FISSURES

Clinpro

™

Sealant

Indications:

• 3M

™

ESPE

™

Clinpro

™

Sealant is designed for sealing the enamel

pits and fissures of teeth to aid in the prevention of caries.

Preparation:

• Select teeth. Teeth must be sufficiently erupted so that a dry

field can be maintained.

• Clean Enamel. Thoroughly clean teeth to remove plaque and

debris from enamel surfaces and fissures. Rinse thoroughly

with water. Note: Do not use any cleaning medium that may

contain oils.

• Isolate teeth and dry. While a rubber dam provides the best

isolation, cotton rolls used in conjunction with isolation shields

are acceptable.

1 of 2

Dry Etched Enamel:

• Thoroughly dry the etched surfaces.

• Air should be oil and water free.

• The dry etched surfaces should appear

as a matte frosty white. If not, repeat

steps 1 and 2. Do not allow the etched

surface to be contaminated.

Etch Enamel:

• Using syringe tip, or fiber tip, apply a

generous amount of etchant to all enamel

surfaces to be sealed, extending beyond

the anticipated margin of the sealant.

• Etch for a minimum of 15 seconds, but

no longer than 60 seconds.

Rinse Etched Enamel:

• Thoroughly rinse teeth with air/water spray

to remove etchant.

• Do not allow patient to swallow or rinse.

If saliva contacts the etched surfaces, re-

etch for 5 seconds and rinse.

SEALING PITS AND FISSURES

Clinpro

™

Sealant

2 of 2

3M ESPE Customer Hotline 1-800-634-2249 70-2009-2437-4B

Please refer to instructions for more detailed information 44-0023-3836-4B

3M, ESPE and Clinpro are trademarks of 3M or 3M ESPE AG.

Apply Sealant:

• Using the syringe needle tip, or a brush,

apply sealant into the pits and fissures.

Do not let sealant flow beyond the etched

surfaces.

• Stirring the sealant with the syringe-tip

during or after placement will help

eliminate any possible bubbles, and

enhance the flow into the pit and fissures.

An explorer may also be used.

Light-Cure:

• Cure the sealant by exposing it to light

from a 3M

™

ESPE

™

Light-Curing Unit, or

other curing unit of comparable intensity.

• A 20-second exposure is needed for each

surface. The tip of the light should be

held as close as possible to the sealant,

without actually touching the sealant.

• When set, the sealant forms a hard,

opaque film, light yellow in color with a

slight surface inhibition.

Wipe Clean:

• Wipe the sealant with a cotton applicator

to remove the thin film on the surface.

3M Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP User guide

Brand: 3M

Model: Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP

Type: User guide

This manual is also suitable for

Download PDF

report

3M Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP User guide

This manual is also suitable for

3M Clinpro™ Sealant & Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Trial Kit, 12626TP User guide

Related papers

Other documents