Minka Group 72593-143C User manual

Type
User manual

Minka Group 72593-143C is a stylish and functional fixture, ideal for illuminating various indoor spaces. It features four candle-shaped sleeves, each accommodating a 40W E12 bulb (not included). With its classic design and warm, inviting glow, this fixture adds a touch of elegance to any room. Installation is straightforward, requiring basic electrical skills and tools. Simply follow the provided instructions to mount the fixture, connect the wires, and secure the backplate. Remember to consult a qualified electrician if needed.

Minka Group 72593-143C is a stylish and functional fixture, ideal for illuminating various indoor spaces. It features four candle-shaped sleeves, each accommodating a 40W E12 bulb (not included). With its classic design and warm, inviting glow, this fixture adds a touch of elegance to any room. Installation is straightforward, requiring basic electrical skills and tools. Simply follow the provided instructions to mount the fixture, connect the wires, and secure the backplate. Remember to consult a qualified electrician if needed.

INSTALLATION INSTRUCTIONS
Model # 72593
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
PREPARING FOR INSTALLATION (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker
box and remove the old fixture, including the
mounting hardware.
2. Carefully unpack your new fixture and lay out all the
parts in a clear area. Take care not to misplace any
small parts necessary for installation.
3. Align mounting plate (A) to the outlet box (C) (not
included) and use it as a template to mark the
location of the wall anchors (H). Make sure "GND"
facing outside. Pre-drill the holes for the wall
anchors (H) and insert the anchors into the wall.
4. Remove the pre-punching hole in mounting plate
(A). Attach mounting plate (A) using outlet box
screws (B) to the outlet box (C) and screws (G) into
wall anchors (H), Make sure "GND" facing outside
(Fig 1).
5. Align back plate (F) onto the mounting plate (A)
and slip the hook (I) hang on the mounting plate
(A). (Fig 1)
CONNECTING THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in Fig.2.
Make sure that all wire connectors are secured. If
your outlet box has a ground wire (green or bare
copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly
to the long strap using the green screw (D)
provided.
COMPLETING THE INSTALLATION (Fig. 1)
7. Align back plate (F) onto mounting plate (A), and
secure with screw (E). (Fig 1)
8. To prevent moisture from entering the outlet box
(C) and causing a short, use clear silicone sealant
(i.e. Indoor/Outdoor Silicone Sealant) to outline the
outside of fixture back plate (F) where it meets the
wall leaving a space at bottom to allow moisture a
means to escape. (Fig.3)
9. At this point, install 4*40W/E12/B bulb (no bulb
included) in accordance with the fixture
specification
DO NOT EXCEED THE MAXIMUM WATTAGE
RATING! (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the
outlet box and test the fixture.
BARE COPPER(GROUND)
Fig.2
FIXTURE
WIRES
WHITE
BLACK
(HOT)
WIRES
HOUSE
GREEN OR
WHITE
(NEUTRAL)
WIRES
HOUSE
(GROUND)
COPPER
BARE
FIXTURE
WIRES
BLACK
WIRES
FIXTURE
GREEN OR
HOUSE
WIRES
Candle Sleeve #
CCV22114P-143
SET A-021-120345
-Mounting plate
-Ground Screw
-Mounting Screws(2)
“CAUTION-RISK OF FIRE CONSULT A
QUALIFIED ELECTRICIAN TO ENSURE
CORRECT BRANCH CIRCUIT CONDUCTOR”
ATTENTION RISQUE D’INCENDIE, CONSULTER UN
ÉLECTRICIEN QUALIFIÉ POUR VOUS ASSURER QUE
LES CONDUCTEURS DE LA DÉRIVATION SONT
ADÉQUATS.
  • Page 1 1

Minka Group 72593-143C User manual

Type
User manual

Minka Group 72593-143C is a stylish and functional fixture, ideal for illuminating various indoor spaces. It features four candle-shaped sleeves, each accommodating a 40W E12 bulb (not included). With its classic design and warm, inviting glow, this fixture adds a touch of elegance to any room. Installation is straightforward, requiring basic electrical skills and tools. Simply follow the provided instructions to mount the fixture, connect the wires, and secure the backplate. Remember to consult a qualified electrician if needed.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI