Minka Lavery 9147-407 Installation guide

Brand
Minka Lavery
Model
9147-407
Type
Installation guide

Minka Lavery 9147-407 is a light fixture designed for indoor use. It features a long strap that allows for easy attachment to an outlet box, and it comes with all the necessary hardware for installation. The fixture has a ground wire for safety, and it can be used with bulbs that have a maximum wattage rating as specified in the instructions. The fixture also includes a cage that can be removed to install light bulbs, and it has a nipple and bottom finial for added stability.

Minka Lavery 9147-407 is a light fixture designed for indoor use. It features a long strap that allows for easy attachment to an outlet box, and it comes with all the necessary hardware for installation. The fixture has a ground wire for safety, and it can be used with bulbs that have a maximum wattage rating as specified in the instructions. The fixture also includes a cage that can be removed to install light bulbs, and it has a nipple and bottom finial for added stability.

INSTALLATION INSTRUCTIONS
Model # 9147
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
1.
Shut off power at the circuit breaker and remove old
fixture including mounting hardware.
2.
Carefully unpack your new fixture and lay out all the
parts in a clear area. Take care not to misplace any
small parts necessary for installation.
3. Make two holes on the wall in correct position
in
accordance with the long strap (C) and the outlet box
(A), then insert the anchor (E) into the hole.
4. Pull black and white wires out of electrical outlet box
(A).
5. Thread the four studs (B) into the pre-
drilled holes in the
long strap (C) spaced the same distance apart as the
holes in the back plate (F).
6. Attach long Strap (C) using Outlet Box Screws (D
) to
the outlet box (A)
, screw the wood screws (G) into the
anchor (E) (Fig 1).
7. Connect the electrical wires as shown in Fig.2. M
aking
sure that all wire conne
box
has a ground wire (green or bare copper), connect
the fixture’s Ground wire to it. Otherwise,
connect the
fixture’s Ground wire directly to the long strap
using the
Green Screw (H) provided.
8. To prevent moisture from entering the outlet box (A)
and causing a short, use clear silicone Sealant to
outline the outside of fixture back plate (F) where it
meets the wall leaving a space at bottom to allow
moisture a means to escape.
9. Place the back plate (F) into stud (B) and secure it
tightly against the wall using cap nut (I). (Fig 1)
10. At this point, screw the extended nut (N), remove the
cage (M) to i
nstall the light bulbs in accordance with the
fixture specification. –-DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!
11. Replace the cage (M), tighten with the extended nut
(N),then screw the nipple(O) and secure with the bottom
finial(P).
12. Replace the rubber washer (L), secure the top finial (J)
with the nipple (K).
Your installation is now complete. Return power to the
outlet box and test the fixture.
Fig. 1
BARE COPPER(GROUND)
Fig.2
FIXTURE
WIRES
WHITE
BLACK
(HOT)
WIRES
HOUSE
GREEN OR
WHITE
(NEUTRAL)
WIRES
HOUSE
(GROUND)
COPPER
BARE
FIXTURE
WIRES
BLACK
WIRES
FIXTURE
GREEN OR
HOUSE
WIRES
R
D
A
C
B
I
J
K
M
N
O
P
E
G
L
F
H
“CAUTION
-
RISK OF FIRE
,
CONSULT
A
QUALIFIED ELECTRICIAN TO ENSURE
CORRECT BRANCH CIRCUIT CONDUCTOR”
  • Page 1 1

Minka Lavery 9147-407 Installation guide

Brand
Minka Lavery
Model
9147-407
Type
Installation guide

Minka Lavery 9147-407 is a light fixture designed for indoor use. It features a long strap that allows for easy attachment to an outlet box, and it comes with all the necessary hardware for installation. The fixture has a ground wire for safety, and it can be used with bulbs that have a maximum wattage rating as specified in the instructions. The fixture also includes a cage that can be removed to install light bulbs, and it has a nipple and bottom finial for added stability.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents