Minka Lavery 73093-189 User manual

Brand
Minka Lavery
Model
73093-189
Type
User manual
INSTALLATION INSTRUCTIONS
Model # 73093
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig 3
Caulking
Backplate
PREPARING FOR INSTALLATION
(Fi
g.
1
)
1. Shut off power at the circuit breaker (avertissement! couper le
courant au niveau des fusibles ou du disjoncteur) and remove
the old fixture including mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a
clear area. Take care not to misplace any small parts necessary
for installation.
3. Unscrew knobs (I), and separate mounting plate (C) (part #:A-
020) from back plate (J). Attach mounting plate (C) to outlet box
(A) with outlet box screws (E) (size:8-32*1/2L). Note: the side
of the mounting plate marked “GND” must face out.
4. Separate fixture body (O) from top cover (Q) by removing
screws (P)
5. Align large glass (L) and small glass (K) into fixture body (O)
and secure with glass clips (M). Secure fixture body (O) to top
cover (Q) with screws (P).
6. Align decorative arm (H) through top loop (F) and secure it to
back plate (J) with the screw (G).
7. Thread the two mounting screws (B) into the pre-drilled holes
on mounting plate (C) spaced the same distance apart as the
holes on back plate (J). Secure mounting screws (B) into
mounting plate (C) with the hex nuts provided. Note: The length
of mounting screws (B) into mounting plate (C) may be
adjusted if necessary.
CONNECTION THE WIRES (Fig. 2)
8. Connect the electrical wires as shown in Fig.2. making sure
that all wire connectors are secured. If your outlet box has a
ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap using the green screw
FINISHING THE INSTALLATION (Fig.1)
9. Align back plate (J) onto mounting screws (B) and secure with
rubber washers (D) and cap nuts (I). (Fig .1). Place candle
cover (N) onto the sockets.
10. Install 60W / type B bulbs (bulbs not included) in accordance
with the fixture specification.
(DO NOT EXCEED THE
MAXIMUM WATTAGE RATING! (NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!))
11. To prevent moisture from entering the outlet box (A) and
causing a short, use clear silicone sealant to outline the outside
of fixture back plate (J) where it meets the wall leaving a space
at bottom to allow moisture a means to escape. (Fig .3)
Your installation is now complete. Return power to the outlet box and
test the fixture.
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED
ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.
Fig.2
Fig.
1
A
B
C
D
P
M
L
N
Q
F
J
H
G
K
O
E
Set #:A-020
Circular Strap(1)
Ground Screw(1)
Mounting Screw(2)
  • Page 1 1

Minka Lavery 73093-189 User manual

Brand
Minka Lavery
Model
73093-189
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents