Reznor EBHB Installation guide

Brand: Reznor

Model: EBHB

Type: Installation guide

Reznor EBHB is an electric baseboard heater designed to provide warmth and comfort in various residential and commercial spaces. It features a built-in thermostat for precise temperature control, ensuring energy efficiency and customized heating. The heater is equipped with safety features such as overheat protection and a high-temperature warning system for added peace of mind. Its sleek design and compact size make it suitable for installation in tight spaces, providing a discreet heating solution without compromising on performance.

THE INSTALLATION MUST BE EXECUTED

BY A QUALIFIED TECHNICIAN

RISK OF ELECTROCUTION

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions

should always be taken to reduce the risk of ﬁ re,

electric shock, and injury, including the following:

Read all instructions before using this heater.

- A heater has hot and arcing or sparking parts inside.

Do not use it in areas where gasoline, paint, or ﬂ ammable

liquids are used or stored.

- This heater is hot when in use. To avoid burns, do not let bare

skin touch hot surfaces. Keep combustible materials, like

furniture, pillows, bedding, papers, clothes, and curtains away

from heater.

- To prevent a possible ﬁ re, do not block air intakes or exhaust in

any way whatsoever.

- Do not insert or allow foreign objects to enter any ventilation or

exhaust opening as this may cause an electric shock or ﬁ re, or

damage the heater.

- Do not install heater against combustible low-density cellulose

ﬁ berboard surfaces.

- Do not use outdoors.

- CAUTION - High Temperature; Keep electrical cords, drapes,

and other furnishings away from heater.

- Use only with copper branch circuit conductors.

- For bathroom use, the heater must be installed so that switches

and other controls cannot be touched by anyone in the bath or

shower.

- Do not install this heating appliance beneath a wall outlet.

- To avoid possible electrical shock, disconnect all power at the

main panel prior to wiring, cleaning, or servicing.

- KEEP THESE INSTRUCTIONS.

INS338-201204-01

FURNITURE AND DRAPES

For maximum satisfaction an air ﬂ ow of 3 in. (76.2 mm)

clearance is recommended. Also allow 1 in. (25.4 mm) clearance

on top and bottom of drapes when drapes cover wall.

INSTALLATION INSTRUCTIONS

1- Remove wire holder (or knock-out) of the appropriate junction

box.

2- Make connection according to local and national codes and

replace wire holder. (Do not forget ground wire.)

3- Install the relay or thermostat by removing front panel and

junction box cover.

4- Check wire connection at the other junction box.

5- Fasten the baseboard to the wall using wood screws, tighten

then release 1/2 turn.

6- Replace all covers before energizing.

INTERCONNECTION

The connection boxes and wiring channel are approved for inter-

connection of baseboard heaters and components which are on the

same heating branch circuit. Use ‘‘BX’’ cable to run wiring for

all other options in this series. (Ex: Corner box, empty cabinets,

etc.).The heater junction box minimum volume without options is

31.2 in³ (512 cm³).

CORNERS AND BLANK SECTIONS

Install blank sections and corners the same way as heating unit of

this series. Use ‘‘BX’’cable to run wiring into these options.

OPTIONS

All heating equipment and options must be installed in accordance

with local and national codes.

Built-in thermostat:

CAUTION: The thermostat should not be considered as an

infallible system where maintaining a temperature is considered

critical. Examples: Hazardous material storage, computer room,

etc. In these particular cases, it is imperative to add a monitoring

system to avoid the consequences of a failure of the thermostat.

- Refer to wiring diagram for connections.

- Refer to instructions supplied with the option for mounting.

Built-in relay:

- Refer to the diagram included with the relay option

for connections.

- Refer to instructions supplied with the option for mounting.

MAINTENANCE

- Once a year or at the need, remove the front panel and use a

vacuum cleaner to remove the dust accumulation inside the

heater.

- Cleaning should be done while the heater is disconnected

from the main service panel. Wait until the housing and heating

element cool before performing maintenance.

Remove the front panel.

CAUTION: Fins on the element are sharp - Do not touch.

Replace all covers before energizing.

- Any other servicing should be performed by a qualiﬁ ed

technician.

WARRANTY

The manufacturer warrants the electric heating element of

this product for life. The other component parts are warranted

against defects in material and workmanship for a one year

period following the date of purchase, under normal use and

maintenance, provided that there is a proof of purchase to conﬁ rm

this date. The obligation of the manufacturer, under the terms of

this warranty, is limited to replacing the unit (baseboard heater

only) and excludes all other costs related to the installation or

replacement of the unit or spare parts.

WIRING DIAGRAM

High-Limit

Heating

Element

Heating

Element

Thermostat

1/2’’ (12.7 mm)

6’’ (152.7 mm)

CAUTION

DRAPES

3’’

76.2 mm

1’’ minimum

25.4 mm minimum

Reznor LLC

O’Fallon MO USA 63368

Tel.: 1 800 695-1901

www.ReznorHVAC.com

are the property of their respective organizations.

INSTRUCTIONS INSTALLATION

EBHB Model

Page is loading ...

Reznor EBHB Installation guide

Brand: Reznor

Model: EBHB

Type: Installation guide

Download PDF

report

in other languages

français: Reznor EBHB Guide d'installation

Reznor EBHB Installation guide

Reznor EBHB Installation guide

in other languages

Related papers

Other documents