Home Decorators Collection 1879800410 Operating instructions

Type
Operating instructions

This manual is also suitable for

Home Decorators Collection 1879800410 is an Instant Pendant Light/Recessed Light Conversion Kit that allows you to convert your recessed light fixture into a pendant light in just 10-15 minutes. The kit includes everything you need to make the conversion, including a socket adapter, spindle bracket, canopy, compression nut, thumb ring, and lamp cup.

To use the kit, simply adjust the excess cord by wrapping it around the spindle bracket, screw the adapter into the light bulb socket in your recessed light fixture, slide the canopy up the cord and against the ceiling, and finger tighten the compression nut to hold the canopy in place. Then, attach your shade to the lamp cup and screw on the thumb ring.

Home Decorators Collection 1879800410 is an Instant Pendant Light/Recessed Light Conversion Kit that allows you to convert your recessed light fixture into a pendant light in just 10-15 minutes. The kit includes everything you need to make the conversion, including a socket adapter, spindle bracket, canopy, compression nut, thumb ring, and lamp cup.

To use the kit, simply adjust the excess cord by wrapping it around the spindle bracket, screw the adapter into the light bulb socket in your recessed light fixture, slide the canopy up the cord and against the ceiling, and finger tighten the compression nut to hold the canopy in place. Then, attach your shade to the lamp cup and screw on the thumb ring.

Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-384-9400, 9 a.m.-5 p.m., EST, Monday-Friday . Include
e-mail address if applicable .
Part
Description
Quantity
A
1
B
C
D
E
F
1
1
1
1
1
Socket adapter
Spindle bracket
Canopy
Compression nut
Thumb ring
Lamp cup
Style and finish will vary by item.
D
C
F
A
B
D
E
P ACKAGE CONTENTS
Please read over the instructions, it will be a time-saver in the long run.
Assembly Instructions
HDC#: MFG#:
1879800410 PAN-4300
Instant Pendant Light/Recessed Light Conversion Kit
1. Adjust excess cord by wrapping it around spindle bracket (B)
just below the socket adapter (A). Position the last wrap
so the cord will hang in the center of your recessed light
fixture.
ASSEMBL Y INSTRUCTIONS
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged. Do not attempt to assemble the
product. Contact customer service for replacement parts.
Estimated Assembly Time: 10-15 minutes
Helpful Tools:
A
B
Recessed
light socket
2.Screw the adapter (A) into the light bulb socket in your
recessed light fixture.
3.After finger loosening the compression nut (D) by turning it
counter-clockwise, slide the canopy (C) up the cord and
against the ceiling.
PREPARATION
HELPFUL HINT: If the canopy does not sit tight against the
ceiling, loosen the compression nut (D). GENTLY pull down on
the cord to flex the spring arm (B), then slide the canopy (C),
back up and re-tighten.
4.To hold the canopy in place against the ceiling, finger tighten
the compression nut (D) by turning it clockwise.
Ceiling
CAUTION: Do not over-tighten the compression nut (D).
5.Attach shade(not included) to lamp cup (F) and then screw thumb
ring(E) clockwise until tight.
2
A
Fig.1
Fig.2
Fig.5
Ceiling
Recessed
light fixture
C
D
B
C
D
Fig.3
Fig.4
F
E
Bulb (not included)
CARE AND MAINTENANCE
3
WARRANTY
Bulb is burned out
Power is off
Bad switch
Replace light bulb (not included)
Make sure power supply is on
Test or replace switch
Bulb will not light
Loosen the compression nut (D) and GENTLY
pull down on the cord to flex the spring arm (B),
then slide the canopy (C) back up and re-tighten
Canopy does not fit tight
against the ceiling
Cord has stretched out
Problem
Possible Cause Corrective Action
TROUBLESHOOTING
Printed in China
3
WARNINGS AND CAUTIONS
WARNING
Risk of fire or electrical shock. Do not alter, relocate, or remove wiring, lampholders, ballasts, or any other
electrical component.
Risk of fire or electrical shock. Install this kit only in the luminaries that have the construction features and
dimensions shown in the photographs and/or drawings.
CAUTION
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
The manufactur er warrants against defec ts in materials and workm anship for one (1) year from the date of purchase to
the origin al purchase r. If withi n this period the product is found to be defec tive , take a copy of the bill of sale as a proof
of purch ase and the product in its origin al packa ging to the place of purchase. This warra nty does not cov er products
becom ing damaged or defec tive cause d by abuse , misuse,ac cidents, fault y instal lation, improp er handling and/o r
maint enance, or repairs not carrie d out by the manufactur er. Items which are not covere d by warra nty are those
consid ered as parts which are prone to failur e due to general wear and tear (for example, lamps, fuses , glass mater ials ).
There will be no obliga tions or liabili ty on the part of the manufactur er for con sequenti al damages arisin g from the use
of the product or any indire ct damages with respe ct to loss of property,revenue, or costs for removal. Insta llat ion or
the use of the product or any indire ct damages with respe ct to loss of property, rev enue, or costs for removal,
re-ins tallat ion. As some states do not allo w exclu sions of limitatio ns on an implie d warra nty, the above exclusion and
limita tion may not apply. This warra nty gives you speci fic rights and you may also have other rights which may vary
from state to state.
www. WorthHP.com
U.S. Patent No. 7 ,311,425
Shut off light and let bulb cool if necessary. Wire shade with soft cloth or household glass cleaner. Do not
use abrasive cleaners. For replacement bulbs, bulbs, use 75 watt maximum, Type A or suitable medium
base bulb (not included) including CFLbulbs.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Home Decorators Collection 1879800410 Operating instructions

Type
Operating instructions
This manual is also suitable for

Home Decorators Collection 1879800410 is an Instant Pendant Light/Recessed Light Conversion Kit that allows you to convert your recessed light fixture into a pendant light in just 10-15 minutes. The kit includes everything you need to make the conversion, including a socket adapter, spindle bracket, canopy, compression nut, thumb ring, and lamp cup.

To use the kit, simply adjust the excess cord by wrapping it around the spindle bracket, screw the adapter into the light bulb socket in your recessed light fixture, slide the canopy up the cord and against the ceiling, and finger tighten the compression nut to hold the canopy in place. Then, attach your shade to the lamp cup and screw on the thumb ring.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI