2. Computers & electronics
  3. Data input devices
  4. Keyboards
  5. Monoprice
  6. GM868
GM868

Monoprice GM868 User guide

  • Hello! I've reviewed the user manual for the Collider 65 keyboard. This document covers important aspects of the keyboard, such as its Bluetooth pairing process, RGB backlighting customizations, and battery information. I'm ready to answer any questions you may have about using this device.
  • How long does the battery last in Bluetooth mode?
    How do I know when the battery is low?
    How do I pair the keyboard with a device via Bluetooth?
    How do I switch between paired devices?
    How do I start backlight macro recording?
Collider Membrane Keyboard
–
QIG
Battery and Charging
• Battery – 4 days (2 hours per day) Bluetooth mode. Standby mode – 3 months
• Red LED indicator will illuminate when battery is charging.
• RED LED indicator will shut off when battery is fully charged
• “FN” key backlight LED will flash repeatedly when battery is low
• Backlights will shut off after 5 minutes without use to conserve batter. After 30 minutes
without use keyboard will enter standby mode and disconnect from Bluetooth. Press any
key to exit standby mode and wake up the keyboard.
Bluetooth Pairing Instructions
1. Set switch on the back of the keyboard to the “ON” position
2. Press and hold FN + P for 3-5 seconds
3. The “P” key will begin to flash repeatedly to indicate that the keyboard is ready to conn
ect to a new device over Bluetooth.
4. On the device you wish to connect to, search for Bluetooth devices and select “ Collide
r 65” to pair the device.
5. Once the keyboard has connected to the device, the “P” ley will stop flashing to indicat
e successful Bluetooth pairing.
6. The keyboard can support Bluetooth connections for up to three devices. Press and hol
d FN+P and Q/W/E to set up a connection to a new device.
7. Switch previously paired devices by quickly pressing FM + Q/W/E
RGB Backlighting and Animation Effects
FN+DEL
Cycle backlit modes
–
Breathing. Cycle, Ra
inbow. Sparkle, Glitter, Colorful, Wave, Ch
ase, Ripple
FN+INS
Cycle backlit modes -
Static, Single-on, Sin
gle-off. Rotate, Scroll, Roll, Fall, Colorful, Glitt
er
FN+PG UP
Breathing animation effect
FN+PG DN
Running animation effect
FN+
↑
Cycle through single color mode
–
Red,
Green, Blue, Yellow, Cyan, Pink, White
FN+
↓
Expanding animation effect
FN+
→
Custom mode. Six-are backlit color
FN+
←
Blastoff animation effect
FN+9
Voice/Music/Noise controlled effect. FN+P
GUP/PGDN to change sensitivity.
FN+
→
Toggles direction of current animation effe
ct
FN+
←
Toggles direction of current animation effe
ct
FN+PG UP
Increases backlight animation speed
FN+PG DN
Decreases backlight animation speed
Custom Backlight Mode Instructions:
1. Press Fn + Z/X/C. Each key can store one backlight mode macro.
2. Press Fn+Tab. The blue LED indicator will flash repeatedly to indicate that backlight macro recording
has begun.
3. Press the keys that you wish to set backlighting for.
4. Press Fn+ Tab again to stop backlight macro recording.
Hot Keys
FN+WIN
Lock and unlock windows keys
FN+Backspace
Hold 3 seconds to reset keyboard
FN+Q/W/E
Switch Bluetooth profiles
FN+Z/X/C
Switch custom backlighting profiles
FN + Tab
Backlight macro recording and saving
FCC STATEMENTS:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditio
ns:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
NOTE:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a class B digital device,pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates uses and can radiate radio frequence energy and,if not installed and used in
accordance with the instructions,may cause harmful interference to radio communications.However,there is no
guarantee that interference will not occur in a particular installation.if this equipmemt does cause harmful
interference to radio or television reception,which can be determined by turning the equipment off and on,the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an autlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
/