GNBLAB Allestrong 270 is a professional nail drill with a powerful 65W motor and a smooth speed regulation, allowing for precise and efficient nail shaping and cuticle removal. With a maximum torque of 4.5Ncm and a speed range of up to 35,000 RPM, it ensures effortless operation and superior results. The device features a user-friendly control unit with a speed dial and a reverse rotation switch for added versatility.
GNBLAB Allestrong 270 is a professional nail drill with a powerful 65W motor and a smooth speed regulation, allowing for precise and efficient nail shaping and cuticle removal. With a maximum torque of 4.5Ncm and a speed range of up to 35,000 RPM, it ensures effortless operation and superior results. The device features a user-friendly control unit with a speed dial and a reverse rotation switch for added versatility.
TECHNICAL DATA:
Power: 65W
Rotation speed: 35,000 revolutions per minute with smooth regulation
Maximum Torque: 4.5Ncm
Handle: 2.35mm
Weight: 1.1 kg
Input voltage: 220V / 50Hz
Output voltage: 0-32V
Fuse: 250V AC / 2A
DEVICE CONFIGURATION AND OPERATION:
1. After checking the switch in the control unit, connect the power supply to the electricity supply.
2. Connect the head to the appropriate socket in the device
3. Turn the speed dial to „0”
Attention!
Make sure the drill shank is fully seated in the holder and secured. During operation, the loose tip may come out.
4. Hold the head with one hand and turn on the device with the other.
5. Check that the head is working properly at dierent rotation speeds by using the knob on the device.
6. Turn o the power and connect the pedal to the control unit. Check out his work
7. Turn o the power and switch the device to reverse rotation. Turn on the power and check the milling machine operation.
PRECAUTIONS
• Turn o the power when you are not using the device.
• Do not use the router in hazardous places. Do not use it in wet places.
• Transport and storage conditions:
Temperature: 10-40°C
Air humidity: 30-75% RH
Atmospheric pressure: 700 hPa - 1060 hPa
• The foot control should only be used with the above-mentioned device.
NAIL DRILLS
Drill dimensions: 2.35 mm (ISO7785-2 TYP 2)
Minimum drill assembly length: 10mm
After closing the drill bit in the holder, it should protrude no more than 35 mm.
• Use drill bits that conform to ISO standards.
• Avoid using rusty, bent or damaged drill bits as they can cause excessive wear on the machine and bearings.
• Maintain the safe operating speed of the device specied by the manufacturer and follow the safety rules.
• Any defects or excessive vibration should be checked rst at a low rotation speed and then increased.
• Change the speed of rotation of the control device gradually.
• Use an appropriate power source for the control device.
• Disconnect the machine from the power supply when changing drill bits.
• Be careful not to let the cutter head fall. It may damage or destroy it. If the head is dropped, check that the drill bit has not been
bent and carefully check that the head does not overheat during operation.
• If you have any problems with the printhead, do not use it until it has been repaired.
• Do not connect the device to the power supply with the handle open, as this may short-circuit the motor.
• Make sure the machine is turned o before connecting to the power supply to avoid injuries due to sudden start of the milling
machine.
• The milling machine has an automatic switch that protects the engine against damage. It starts when the engine is too heavily
loaded. Work only within the permissible loads of the milling machine.
• Do not open the handle while the device is running!
• After work, store the head with the drill inserted in it.
• Do not put the printhead down until it stops completely.
• Make sure to unplug the device before moving it.
• Use the correct voltage.
• Use accessories that are appropriate for the device.
• Please refer to the instruction manual to adjust the speed of the milling machine to your particular application.
• Use appropriate protective clothing, especially a mask and goggles. Use an appropriate dust collector and ventilation.
• Keep the workplace clean, debris can cause an accident.
• Adjust the revolutions per minute (RPM) according to table 1. Failure to do so may result in an accident.
• Acceptable RPM may vary with drill bit and material being processed .
PROFESSIONAL NAILS DRILL ALLESTRONG 270
Model: Allestrong 270
Certicate No.: LCS200624095AS, LCS200624094AE
DEVICE DESCRIPTION
ALLESTRONG 270
1. Control box
2. Head
3. Pedal (on / o)
4. Power button
5. Direction of rotation change button
6. Head connector
7. Speed control knob
8. Pedal connector
9. Power connector
10. Fuse socket
Tab.1 Acceptable revolutions per minute (RPM) depending on the bit’s head diameter (mm)
MAINTENANCE
• Keep the workplace clean of dust.
• Remove dust from the transducer regularly with isopropyl alcohol, avoiding getting the inside of the transducer wet.
• Do not apply oil to the head parts or clean it with water. The grease in the bearings can be melted o by the oil.
ASSEMBLY AND REPLACEMENT OF DRILLS / MILLS
1. Turn the handle in the opening direction to open the handle.
2. With the chuck open, insert the drill bit all the way.
3. Rotate the handle towards the closure until you hear a click.
CHANGING THE CARBON BRUSHES
Attention!
• Make sure the power is o before replacing the carbon brushes!
• Run the motor for 1 minute without load to adjust the carbon brushes to the correct position.
• Regularly check the wear of the carbon brushes to avoid serious damage to the machine.
• The motor can be damaged when the carbon brushes are not replaced in a timely manner.
CHANGE OF THE HANDLE
Attention!
• Make sure the handle is properly closed. If the handpiece is rotated continuously with pressure, the handle may separate from
the head.
• Do not disassemble the device yourself, unless you are a skilled mechanic. Parts may be damaged.
REPLACEMENT OF BEARINGS
1. Hook the wrench on the tip, then turn the handle in the opening direction.
2. Turn the key to loosen the tip.
3. Rotate the handle towards the closure again.
4. Turn wrench until tip is removed and bearings can be replaced.
5. If the replacement is incorrectly carried out, the tip may be damaged or destroyed! If you are not a skilled mechanic, do not
disassemble the device yourself.
Attention!
• Clean and fold the handle carefully.
• Do not disassemble the device yourself, if you are not a skilled mechanic, as the handle and motor parts may be damaged or
destroyed.
• When the equipment is removed, the deline joint of the handpiece and motor parts must t together. Otherwise, vibration, noise,
overheating and damage to the head may occur.
• If the handle has not been opened, turn it with the wrench.
FUSE REPLACEMENT
The fuse is located in a small fuse box next to the power cord connector on the back of the control unit. Remove the defective
fuse and replace it with a new one.
(120V-T3. 15A/250V. 230V T2A/250V)
RULES FOR SAFE USE
• Do not use if the power cord, plug or contact are damaged. Contact the manufacturer. Using a damaged device may result in
re or electric shock.
• When you unplug the power cord, grasp it by the plug and do not touch it with wet hands.
• Do not bend the power cord or press it with heavy objects. This may damage it.
• Do not place the router near heating appliances, candles, open ames or cigarettes.
• Special care is required when the device is used near children, the elderly or the disabled.
• Do not leave children unattended in the room where the milling machine is located.
Protection class against electric shock: class I device
Degree of protection against electric shock: type B device
Classication by degree of protection against ingress of water as detailed in the current edition of IEC 60529:
Device: IPX0, common equipment
Pedal: IPX1
• The device should not be used in the vicinity of ammable anesthetics (local anesthetics) or pure oxygen
• Mode of operation: continuous operation.
• The device has been tested and found to comply with the limits for medical devices in IEC 60601-1-2: 1994. These limits are
designed to provide reasonable protection against harmful interference in a typical medical installation. This device generates
radio frequency radiation and, in the event of improper use or installation, may cause harmful interference in the operation of
other devices in the environment. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to other equipment, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by:
turning or repositioning the device
increasing the separation between devices
connecting the device to a separate socket so as not to burden the power line
consult the manufacturer or service technician
• Use an earthing conductor, damage or leakage of the electrical system causes the risk of electric shock. Contact an electrician
to ground the installation.
• When using an extension cord, do not plug multiple devices into it as this may result in re and electric shock hazard.
• Do not place or use the product in a damp, wet or snowy place. This increases the risk of electric shock or burning of the
installation.
• Do not drop or damage the print head. In the event of its malfunction, dropping, dropping or getting wet, do not use the device
and contact the manufacturer or service technician. This can cause drill / cutter vibration, overheating of the machine, or damage
to the bearings.
• Use the device in accordance with the intended use indicated by the manufacturer in the manual and avoid any harmful eects.
• The device can cause injury or property loss if the instructions in the manual are not followed.
• The manufacturer and distributor are not responsible for accidents caused by failure to follow the instructions for use.
IMPORTER
GNB-Lab
Michał Szewczyk, Piotr Malinowski s.c.
Piotrkowska 270,
90-361 Łódź
gnb-lab.com
Made in P.R.C.
-
1
-
2
-
3
-
4
-
5
GNBLAB Allestrong 270 is a professional nail drill with a powerful 65W motor and a smooth speed regulation, allowing for precise and efficient nail shaping and cuticle removal. With a maximum torque of 4.5Ncm and a speed range of up to 35,000 RPM, it ensures effortless operation and superior results. The device features a user-friendly control unit with a speed dial and a reverse rotation switch for added versatility.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Mercedes DM298 User manual
-
KRIS NAILS M13 User manual
-
Grizzly G0759 User manual
-
-
-
-
Grizzly Industrial G0781 Owner's manual
-
Grizzly Industrial G0754 Owner's manual
-
Sherline Products 2010 Assembly And Instruction Manual
-
