Gigabyte MUQ77EI User manual

Category
Motherboards
Type
User manual
MUQ77EI
Intel® Socket uPGA988 processor motherboard
User's Manual
Rev. 1001
Copyright
© 2013 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE
without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentation:
For detailed product information, carefully read the User's Manual.
For product-related information, check on our website at:
http://www.gigabyte.com
- 3 -
Table of Contents
Box Contents ...................................................................................................................4
MUQ77EI Motherboard Layout ........................................................................................5
Chapter 1 Hardware Installation .....................................................................................7
1-1 Installation Precautions .................................................................................... 7
1-2 ProductSpecications ...................................................................................... 8
1-3 Installing the CPU .......................................................................................... 10
1-4 Installing the Memory ..................................................................................... 11
1-4-1 Installing a Memory ...............................................................................................11
1-5 Back Panel Connectors .................................................................................. 12
1-6 Internal Connectors ........................................................................................ 14
Chapter 2 BIOS Setup ..................................................................................................26
2-1 The Main Menu .............................................................................................. 28
2-2 Advanced Menu ............................................................................................. 30
2-2-1 ACPI Settings .........................................................................................................31
2-2-2 Trusted Computing (Optional) ................................................................................32
2-2-3 CPUConguration ..................................................................................................33
2-2-4 SATAConguration.................................................................................................34
2-2-5 Intel (R) Rapid Start Technology ....................................................................... ......35
2-2-6 IntelTXT(LT)Conguration ....................................................................................36
2-2-7 NCT6106DSuperI/OConguration ......................................................................37
2-2-8 NCT6106D HW Monitor ..........................................................................................41
2-2-9 GPIO Control ..........................................................................................................42
2-2-10 Network Stack ........................................................................................................43
2-2-11 CPUPPMConguration .........................................................................................44
2-2-12 Intel (R) 82579LM Gigabit Network Connection .....................................................45
2-3 Chipset Menu ................................................................................................. 47
2-4 Boot Menu ...................................................................................................... 48
2-4-1 CSM Parameters ...................................................................................................49
2-5 Security Menu ................................................................................................ 51
2-5-1 Image Execution Policy .........................................................................................53
2-5-2 Key Management .................................................................................................54
2-6 Exit Menu ....................................................................................................... 56
Chapter 3 Appendix ......................................................................................................58
3-1 Regulatory Statements ................................................................................... 58
- 4 -
Box Contents
MUQ77EI motherboard
Driver CD
Two SATA cables
I/O Shield
The box contents above are for reference only and the actual items shall depend on the product package you obtain.
The box contents are subject to change without notice.
The motherboard image is for reference only.
- 5 -
MUQ77EI Motherboard Layout
1 2 3 4 5 6
11
12
13
14
15
16
17
18
1920
21
22
23
24
25
26
27
33
34
35
28
29
30
31
321
8
7
910
- 6 -
Item Code Description
1 AUDIO Audio connectors
2 USB_LAN2 RJ45 LAN port (top) / USB 2.0 ports
(buttom)
3 USB_LAN1 RJ45 LAN port (top) / USB 2.0 ports
(buttom)
4 USB3 USB 3.0 ports
5 COMC_D Serial ports
6 DP+/VGA/HDMI VGA port (top)/DisplayPort connector
(right)/HDMI port (left)
7 JRS4 RS422 Select jumper
8 JRS5 RS422 Select jumper
9 JRS2 RS485 Select jumper
10 JRS3 RS485 Select jumper
11 JRS1 RS232 Select jumper
12 DISPLAY_BRT Flat Panel Display connector
13 ATX_12V 4 pin power connector
14 RPGA_988 Intel rPGA 988 socket
15 CPU_FAN CPU fan connector
16 SYS_FAN System fan connector
17 SO_DIMM1 DDR3 SO-DIMM slot
18 SO_DIMM2 DDR3 SO-DIMM slot
19 SATAIII_0/SATAIII_1 SATA 6Gb/s connectors
20 SATAII_1/SATAII_0 SATA 3Gb/s connectors
21 ATX 24 pin power connector
22 F_PANEL Front panel header
23 COM4/COM3 Serial port cable connectors
COM4 (left)/COM3 (right)
24 JCOM1 COM1 Power Select jumper
25 COM1/COM2 Serial port cable connectors
COM1 (left)/COM2 (right)
26 LVDS_EN LVDS enable jumper
27 CLR_CMOS Clear CMOS jumper
28 BATTERY Battery power cable connector
29 GPIO GPIO header
30 F_USB2_2 Front USB header #2
31 F_USB2_1 Front USB header #1
32 F_AUDIO Audio cable connector
33 PCIE4X PCI Express x4 slot
34 MPCIE1X Mini PCi Express connector
35 LVDS LVDS connector
- 7 - Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can
become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read
the user's manual and follow these procedures:
• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
• When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
• When handling the motherboard, avoid touching any metal leads or connectors.
• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap,keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.
Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
• Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
• Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
• Do not place the computer system on an uneven surface
.
• Do not place the computer system in a high-temperature environment.
• Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
• If you are uncertain about any installation steps or have a problem related to the use of the
product,pleaseconsultacertiedcomputertechnician.
Chapter 1 Hardware Installation
Hardware Installation - 8 -
1-2 ProductSpecications
CPU Supports Intel® Gen 2/3 Mobile Core i7/i5/i3 processor in Socket uPGA988
TDP 35W
Chipset Intel® BD82QM77 Platform Controller Hub (QM77)
Memory 2 x SO-DIMM slots support DDR3 1333/1600MHz
Support up 16GB
Audio Realtek® ALC887 codec
HighDenitionAudio
2 channel
LAN 1 x Intel® 82579LM controller supports AMT8.0
1 x Realtek® RTL 8111E supports 10/100/1000 Mbps
Expansion Slots 1 x mini PCI Express x1 slot
Onboard
Graphics
Build in Intel® Intel® BD82QM77 Platform Controller Hub (QM77)
Storage Interface 2 x SATA 6Gb/s connectors
2 x SATA 3Gb/s connectors
USB Up to 8 USB 2.0/1.1 ports (4 on the back panel, 4 via the USB brackets connected
to the internal USB headers)
2 x USB 3.0 ports (back panel)
Internal
Connectors
1 x 4 pin ATX 12V power connector
1 x 24 pin ATX main power connector
2 x SATA 6Gb/s connectors
2 x SATA 3Gb/s connectors
1 x CPU fan header
1 x System fan header
4 x COM power select connectors
1 x Front panel header
1 x Audio header
2 x USB 2.0 headers
1 x 10bit GPIO header
1 x LVDS connector
1 x Display connector
1 x Battery power cable connector
Back Panel
Connectors
1 x HDMI port
1 x DP port
1 x VGA port
2 x COM ports
2 x USB 3.0 ports
4 x USB 2.0 ports
2 x RJ-45 port
3 x Audio connectors
I/O Controller iTE IT6512FN chip
- 9 - Hardware Installation
Form Factor Mini ITX Form Factor; 6.75 inch x 6.75 inch
*GIGABYTE reservesthe right to make any changesto the product specications and product-related information
without prior notice.
Hardware
Monitor
System voltage detection
CPU/System temperature detection
CPU/System fan speed control
* Whether the CPU/system fan speed control function is supported will depend on
the CPU/system cooler you install.
BIOS AMI BIOS
Hardware Installation - 10 -
1-3 Installing the CPU
Read the following guidelines before you begin to install the CPU:
• Make sure that the motherboard supports the CPU.
• Always turn off the computer and unplug the power cord from the power outlet before installing
the CPU to prevent hardware damage.
• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
• Apply an even and thin layer of thermal grease on the surface of the CPU.
• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and
damage of the CPU may occur.
• SettheCPUhostfrequencyinaccordancewiththeCPUspecications.Itisnotrecommended
thatthesystembusfrequencybesetbeyondhardwarespecicationssinceitdoesnotmeetthe
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specifications, please do so according to your hardware specifications including the CPU,
graphics card, memory, hard drive, etc.
Installation Steps:
1. The processor socket incorporate a security screw to prevent accidental processor release. Before
installing, please disengage the lock.
2. InserttheCPUwiththecorrectorientation.TheCPUonlytsinoneorientation.
3. Turn the security screw clock-wise toward the Lock symbol to engage the lock.
1
2
- 11 - Hardware Installation
1-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
Make sure that the motherboard supports the memory. It is recommended that memory of the
same capacity, brand, speed, and chips be used.
Always turn off the computer and unplug the power cord from the power outlet before installing
the memory to prevent hardware damage.
Memory modules have a foolproof design. A memory module can be installed in only one
direction. If you are unable to insert the memory, switch the direction.
1-4-1 Installing a Memory
Installation Step:
Step 1. Align the memory with the SO-DIMM module and insert the SO-DIMM memory module into the
SO-DIMM slot.
Please note that memory module has a foolproof insertion design. A memory module can be
installed In only one direction.
Step2. Pushthememoryandseatitrmly.
Step 3. Reverse the installation steps when you wish to remove the SO-DIMM module.
1
2
Hardware Installation - 12 -
1-5 Back Panel Connectors
Video Port
The video in port allows connect to video in, which can also apply to video loop thru function.
HDMI Port
TheHDMI(High-DenitionMultimediaInterface)providesanall-digitalaudio/videointerfaceto
transmit the uncompressed audio/video signals and is HDCP compliant. Connect the HDMI
audio/video device to this port. The HDMI Technology can support a maximum resolution of
1920x1200 pixel but the actual resolutions supported depend on the monitor being used.
DP (DisplayPort) Connector
DisplayPort is a digital display interface which is primarily used to connect a video source to a display
device such as a computer monitor, though it can also be used to transmit audio, USB, and other forms
of data.
Serial Port
Connects to serial-based mouse or data processing devices.
USB 3.0 Port
The USB port supports the USB 3.0 specification. Use this port for USB devices such as a USB
keyboard/mouse,USBprinter,USBashdriveandetc.
USB 2.0 Port
The USB port supports the USB 2.0 specification. Use this port for USB devices such as a USB
keyboard/mouse,USBprinter,USBashdriveandetc.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
Line In Jack (Blue)
The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be
usedtoconnectfrontspeakersina4/5.1/7.1-channelaudioconguration.
• When After installing the HDMI device, make sure the default device for sound playback is the
 HDMIdevice.(Theitemnamemaydifferbyoperatingsystem.Refertheguresbelow
for details.), and enter BIOS Setup, then set Onboard VGA output connect to D-SUB/
HDMI under Advanced BIOS Features..
• Please note the HDMI audio output only supports AC3, DTS and 2-channel-LPCM
formats. (AC3 and DTS require the use of an external decoder for decoding.)
- 13 - Hardware Installation
• Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour
device and then remove it from the motherboard.
• When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
Activity LED
Connection/
Speed LED
LAN Port
Activity LED:Connection/Speed LED:
State Description
Orange 1 Gbps data rate
Green 100 Mbps data rate
Off 10 Mbps data rate
State Description
Blinking Data transmission or receiving is occurring
Off No data transmission or receiving is occurring
MIC In (Pink)
The default MIC In jack. Microphone cab be connected to MIC In jack.
Hardware Installation - 14 -
1-6 Internal Connectors
1
2
34
5
6
7
8
9
18
25
26
14
15 16 17
23
13
24
19
20
21
22
11
10
12
1) ATX1
2) ATX_12V
3) SATAIII_0/SATAIII_1
4) SATAII_1/SATAII_0
5) CPU_FAN
6) SYS_FAN
7) DISPLAY_BRT
8) COM4
9) COM3
10) COM2
11) COM1
12) JCOM1
13) JRS1
14) JRS4
15) JRS5
16) JRS2
17) JRS3
18) F_PANEL
19) GPIO
20) F_USB2_2
21) F_USB2_1
22) F_AUDIO
23) LVDS
24) BATTERY
25) CLR_CMOS
26) JLVDS_EN
Read the following guidelines before connecting external devices:
• First make sure your devices are compliant with the connectors you wish to connect.
• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
- 15 - Hardware Installation
F_PANEL
F_PANEL
F_AUDIO
F_AUDIO
F_USB
COMB
MODEM
Smart Card Reader
SPDIF
AUX_IN
CD_IN
Secure Gigital /
Memory Stick
Serial ATA
F_USB
F_1394
CPU_FAN
SYS_FAN
PWR_FAN
NB_FAN
Power
WOL
SUR_CEN
IR/CIR
F_PANEL
F_PANEL
PWR_LED
CLR_CMOS
BIOS_WP
CLR_CMOS
BIOS_WP
CI
DPVRM
CLR_PWD
FDD
ATX
ATX_12V
IDE
IR
COMB
SPDIF_IO
F1_1394 F2_1394
GAME SMB_CONN F_AUDIO
(NEW)
F1_1394
4
3
2
1
1/2) ATX/ATX_12V (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the
componentsonthemotherboard.Before connecting the power connector,rst make surethepower
supply is turned off and all devices are properly installed. The power connector possesses a foolproof
design. Connect the power supply cable to the power connector in the correct orientation. The 12V
power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the
computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide the
required power, the result can lead to an unstable or unbootable system.
PinNo. Denition
1 GND
2 GND
3 +12V
4 +12V
13
1
24
12
ATX
ATX_12V
F_PANEL
F_PANEL
F_AUDIO
F_AUDIO
F_USB
COMB
MODEM
Smart Card Reader
SPDIF
AUX_IN
CD_IN
Secure Gigital /
Memory Stick
Serial ATA
F_USB
F_1394
CPU_FAN
SYS_FAN
PWR_FAN
NB_FAN
Power
WOL
SUR_CEN
IR/CIR
F_PANEL
F_PANEL
PWR_LED
CLR_CMOS
BIOS_WP
CLR_CMOS
BIOS_WP
CI
DPVRM
CLR_PWD
FDD
ATX
ATX_12V
IDE
IR
COMB
SPDIF_IO
F1_1394 F2_1394
GAME SMB_CONN F_AUDIO
(NEW)
F1_1394
PinNo. Denition
13 3.3V
14 -12V
15 GND
16 PS_ON
17 GND
18 GND
19 GND
20 -5V
21 +5V
22 +5V
23 +5V
24 GND
PinNo. Denition
1 3.3V
2 3.3V
3 GND
4 +5V
5 GND
6 +5V
7 GND
8 Power Good
9 5VSB (stand by +5V)
10 +12V
11 +12V
12 3.3V
Hardware Installation - 16 -
PinNo. Denition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
PinNo. Denition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
7
7
7
7
1
1
1
1
DEBUG
PORT
G.QBOFM
DEBUG
PORT
G.QBOFM
DEBUG
PORT
G.QBOFM
DEBUG
PORT
G.QBOFM
4) SATAII_1/SATAII_0(SATA 3Gb/s Connectors)
The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5 Gb/s
standard. Each SATA connector supports a single SATA device.
3) SATAIII_0/SATAIII_1 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and
1.5Gb/s standard. Each SATA connector supports a single SATA device.
 ARAID0orRAID1congurationrequiresatleasttwoharddrives.Ifmorethantwoharddrives
arecongured,thetotalnumberofharddrivesmustbeanevennumber.
 ARAID10congurationrequiresfourharddrives.
(Note) WhenaRAIDcongurationisbuiltacrosstheSATA6Gb/schannels,thesystemperformanceof
  theRAIDcongurationmayvarydependsonthedevicesareconnected.
SATAIII_0
SATAIII_0
SATAII_1
SATAIII_1
SATAII_0
SATAII_1
SATAIII_1
SATAII_0
- 17 - Hardware Installation
5/6) CPU_FAN/SYS_FAN (CPU Fan/System Fan Headers)
The motherboard has one 4-pin CPU fan header (CPU_FAN), one 4-pin (SYS_FAN) system fan
headers. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure
to connect it in the correct orientation (the black connector wire is the ground wire). The motherboard
supports CPU fan speed control, which requires the use of a CPU fan with fan speed control design. For
optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.
Be sure to connect fan cables to the fan headers to prevent your CPU and system from
overheating. Overheating may result in damage to the CPU or the system may hang.
 Thesefanheadersarenotcongurationjumperblocks.Donotplaceajumpercapontheheaders.
CPU_FAN
1
15
DEBUG
PORT
G.QBOFM
SYS_FAN
PinNo. Denition
1 GND
2 +12V
3 Sense
4 Speed Control
PinNo. Denition
1 VCC_BKL
2 VCC_BKL
3 GND
4 L_BKLTCL_INV
5 L_BKLTEN_INV
7) DISPLAY_BRT (Display Brightness Connector)
Hardware Installation - 18 -
8/9/10/11) COM4/COM3/COM2/COM1 (Serial Port Headers)
The COM header can provide one serial port via an optional COM port cable. For purchasing the
optional COM port cable, please contact the local dealer.
PinNo. Denition
1 NDCDA-
2 NDSRA-
3 NSINA
4 NRTSA-
5 NSOUTA
6 NCTSA-
7 NDTRA-
8 RIA/+5V/+12V
9 GND
10 NC
PinNo. Denition
1 NDCDB-
2 NDSRB-
3 NSINB
4 NRTSBB-
5 NSOUTB
6 NCTSB-
7 NDTRB-
8 NRIB
9 GND
10 NC
PinNo. Denition
1 NDCDE-
2 NDSRE-
3 NSINE
4 NRTSE-
5 NSOUTE
6 NCTSE-
7 NDTRE-
8 NRIE-
9 GND
10 NC
PinNo. Denition
1 NDCDF-
2 NDSRF-
3 NSINF
4 NRTSF-
5 NSOUTF
6 NCTSF-
7 NDTRF-
8 NRIF
9 GND
10 NC
COM4
COM4COM3COM2COM1
COM1
COM3
COM2
1
2
9
10
12) JCOM1 (5V/12V/RI for Serial Port Option Header)
2
65
1
2
65
1
2
65
1
1-2 Close: 5V (Power COM)
3-4 Close: RI (STAND COM)
5-6 Close: 12V (Power COM)
- 19 - Hardware Installation
13) JRS1 (RS232/RS422/RS485 Select Header)
PinNo. Denition
1 RS232
2 RXD Signal
3 RS422
4 RXD Signal
5 RS485
6 RXD Signal
41
42
41
42
1-2 Close: RS232 (Default setting)
3-4 Close: RS422
5-6 Close: RS485
1
26
5
14/15/16/17) JRS4/JRS5/JRS2/JRS3 (RS232/RS422/RS485 Mode Select Jumper)
1
PinNo. Denition
1 RS485 B Signal
2 -NDCDC_D
3 NDCDC
JRS2
PinNo. Denition
1 RS485 A Signal
2 NRXDC_D
3 NRXDC
JRS3
PinNo. Denition
1 RS422 B Signal
2 -NDTRC_D
3 -NDTRC
JRS5
PinNo. Denition
1 RS422 A Signal
2 -NTXDC_D
3 -NTXDC
JRS4
JRS4JRS5JRS2JRS3
1-2 Close: RS485
2-3 Close: RS232 (Default setting)
1-2 Close: RS485
2-3 Close: RS232 (Default setting)
1-2 Close: RS422
2-3 Close: RS232 (Default setting)
1-2 Close: RS422
2-3 Close: RS232 (Default setting)
Hardware Installation - 20 -
18) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status
indicator on the chassis to this header according to the pin assignments below. Note the positive and
negative pins before connecting the cables.
2
1
14
13
The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis
front panel module to this header, make sure the wire assignments and the pin assignments are
matched correctly.
PinNo. SignalName Denition
1 HD+ Hard Disk LED Signal anode (+)
2 MPD+ Power LED Signal anode (+)
3 HD- Hard Disk LED Signal cathode(-)
4 MPD- Power LED Signal cathode(-)
5 GND Ground
6 PW+ Power Button anode (+)
7 RESET Reset Button
8 PW- Power Button cathode(-)
9 RSV Reserved
10 NC No Pin
11 UP 3V Power
12 DOWN LAN2 active LED Signal
13 UP1 3V Power
14 DOWN1 LAN1 active LED Signal
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59

Gigabyte MUQ77EI User manual

Category
Motherboards
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI