Secure Home SH-9910AU Installation And Operating Instructions Manual

FEATURES

•EnergyecientLEDlightsource.

•Automatically comesonwhenmotion isde-

tected.

•Automaticallyturnslighto.

•Photocell keeps the light o during daylight

hours.

•LED indicates motion was sensed (day or

night).

UNPACKING

Besuretoremoveallcontentsfrompackaging

andverifyallitemsarepresentbeforeassembling

thislightxture.ispackageincludesthefol-

lowingitems:

•LEDSecurityLight

•CanopyExtensionwithRubberGasket

•RubberPlug

•MountingBolt

•Owner’sManual

REQUIREMENTS

•elightcontrolrequires230voltsAC.

•IfyouwanttouseManualMode,thecontrol

mustbewiredthroughaswitch.

•It is illegal for persons other than a licensed

electrician or person authorized by legislation

to work on xed wiring or other electrical

installations.

Before installation, record the model num-

ber listed inside the xture. Attach receipt

in case of possible warranty issues.

Model Number:

Installation and Operating Instructions

Motion Sensing

Light Control

Model: SH-9910AU

Security Light*

*Note:Illustrationsareforreferenceonlyandmay

bedierentfromactualproduct

2201115-01

IMPORTANT SAFETY AND INSTALLATION INFORMATION

Beforeinstallingsecuritylight,readallinstructionscarefullyandkeepowner’smanualforfuture

reference.

•WARNING:Topreventelectricshock,pleaseensurethatpowerisdisconnectedbeforeinstallation.

•

WARNING:Riskofre.Donotaimthelampheadsatacombustiblesurfacewithin1meter(3feet).

•isxturemustbeconnectedtoa230V-240V~50Hzpowersource.

•exturemustbeproperlygrounded.

•isxtureisdesignedforoutdoorinstallationandshouldbemountedtoawalloreaves.

•

Toachievebestresults,thisxtureshouldbemounted2.4meters(8feet)abovetheground.Note:Ifxture

ismountedhigherthan2.4meters(8feet),aimingthesensordownwillreducecoveragedistance.

•Donotusedimmerswitchesortimerswiththisxture.

esensoronthislightxturedetects“motion”bythemovementofheatacrossthecoveragearea.How-

ever,followingareexamplesofobjectsthatalsoproduceheatandcancausethesensortotrigger:

•PoolsofWater •AirConditioners

•DryerVents •Animals

•HeatingVents •AutomobileTrac

Ifyoususpectthataheatsourceofthistypeistriggeringthesensor,reducethesensitivity.

esensoronthisxtureismoresensitivetothemovementofheatmovingacrossthecoveragearea

andlesssensitivetothemovementofheatdirectlytowardsit.

Note:Lightxtureandsensorshouldbemountedasshownabovewheninstalled(dependingupon

typeofinstallation).

Wall Mount Eave Mount

Least Sensitive Most Sensitive

Sensor

Motion Motion

201115-01

LNGND

INSTALLATION

This light xture must be installed by a

licensed electrician or other person autho-

rized by legislation to work on xed wiring

or other electrical installations.

IMPORTANT: Do NOT use with dimmers or

timers.

Forbestperformance,mountthextureabout2.4

meters(8feet)abovetheground.Note:Ifxtureis

mountedhigherthan2.4meters(8feet),aiming

thesensordownwillreducecoveragedistance.

isxturecomeswithacanopyextension.Itis

pre-assembledonthextureforshipping.

1. Removethecentermountingboltconnecting

thexturecanopytothecanopyextension(see

Figure1).Note:Besurerubbergasketison

thecanopyextension.

2. Placethecanopyextensionagainstthemount-

ing surface and mark the positions for the

mountingscrews(seeFigure2).Note:When

positioningthecanopyextensionformounting,

dothefollowing:

•Keepthemountingtabslevel

•Makesurethecanopyextensionisturned

asshowninFigure2

•Makesurethehousewiringislocatedbehind

orbelowtherubbergrommet.

3. Useapowerdrilltodrillintothewalltoprovide

asuitablemountingforthescrews.

•Canopyextensionmountingscrewsarenot

included.Use4mmdia.(8G)x30mmscrews.

•Careshouldbetakentoavoiddrillingor

screwingintoconcealedelectricalwiring.

•Forsolidbrickwalls,screwsandmasonry

plugsshouldbeused.

4. Makeasmallholeintherubbergrommetand

route the house wire through the hole (see

Figure3).

5. Attachthecanopyextensiontothesurface.

WARNING: Turn power o at circuit

breaker or fuse. Place tape over circuit

breaker switch and verify power is o at

the xture.

Mounting

Bolt

Rubber Gasket

Fixture Canopy (Lamp

heads and sensor not

shown for clarity)

Mounting Tab

House Wiring

Rubber

Grommet

Canopy Extension

Figure 1

Figure 2

Figure 3

4mm dia. (8G)

x 30mm Screw

4201115-01

FINAL ASSEMBLY

1. Doublecheckallwiringconnections.

2. Verify the rubber gasket is properly seated

aroundtheedgeofthecanopyextension(see

Figure6).

3. Alignthecenterholeonthexturecanopy

withthecenterholeonthecanopyextension

andattachusingthemountingboltremoved

instep1ofInstallation(seeFigure6).

IMPORTANT:

•Ifwall mounted,makesurethe xtureis

mountedwiththesensorbelowthelamp

heads.

•If eave mounted, mount the xture with

sensorfacingawayfromthehousewall(see

Eave Installation Information forimportant

sensororientationinformation).

4. Pushtherubber plugrmlyintoplace(see

Figure7).

5. Caulk around top half of canopy extension

withsiliconeweathersealant(seeFigure7).

Terminal Block

From Fixture From AC Source

WIRING

1. Connectthehousewirestotheterminalblock

according to diagram (see Figure 4). Make

sureallscrewsonterminalblockaretightened

securely.

2.

Removethestrainreliefcoverandplacethehouse

wiresacrossthestrainrelief(seeFigure5).

3. Replace the strain relief cover and tighten

securely.Note:Becarefulnottoovertighten

anddamagethewiring.

WARNING: Turn power o at circuit

breaker or fuse. Place tape over circuit

breaker switch and verify power is o at

the xture.

Green/YellowGreen/Yellow

Blue Blue or Black

Brow

ed or Brown

Figure 4

Terminal Block

House Wiring

Screw

Strain Relief

Cover

Figure 5

Figure 6

Mounting

Bolt

Rubber Gasket

Fixture Canopy (Lamp

heads and sensor not

shown for clarity)

201115-01

EAVE INSTALLATION

INFORMATION

IMPORTANT: For under eaveinstallation only,

thesensorheadmustberotatedasshowninthe

nexttwostepsforproperoperationandtoavoid

theriskofelectricalshock.

1. Rotate the sensor head towards the clamp

screwjoint(seeFigure8).

2. enrotatethesensorheadclockwise180°so

thecontrolsfacedown(seeFigure9).

Note:Ifthesensorpopsoutoftheballjoint,loosen

theclampscrewandpushthesensorbackintothe

balljoint.Tightentheclampscrewwhendone.

TESTING AND ADJUSTMENTS

1. Turn on the circuit breaker and light

switch.

Note:Sensorhasa11/2minutewarmupperiod

beforeitwilldetectmotion.Whenrstturned

onwait11/2minutes.

2. Set:

•ON-TIMEswitchtoTEST

•RANGEdialtoMidwayposition

Clamp Screw

Controls

Figure 7

Figure 8

Figure 9

Canopy

Extension

Rubber Plug

Caulk Upper Half of Canopy Extension

Bottom of Sensor

ON-TIME

10 5 1 TEST

MIN MAX

RANGE

Figure 10

3. Adjustthelampholdersbylooseningthelock

nutsbutdonotrotatethelampholdersmore

than180°fromthefactorysetting(seeFigure

10).Afterpositioningbulbholders,tightenthe

locknutsandapplythreadsealanttoensure

bulbholdersdonotrotate.

Keep lamp

heads at least

25 mm (1") from

the sensor.

Avoid water damage and electrical shock -

keep lamp heads below horizontal.

Lock Nuts

WARNING: Risk of re. Do not aim the

lamp heads at a combustible surface within

1 meter (3 feet).

6201115-01

Note:Whenrstturnedonwaitabout11/2minutes

forthecircuitrytocalibrate.

*resetstoAutoModeatdawn.

OPERATION

MANUAL MODE

Mode: On-Time Works: Day Night

Test 5Seconds x x

Auto 1,5,or10

Minutes x

Manual ToDawn* x

... back on.

1 Second

OFF then...

Manual mode only works at

night because daylight returns

thesensortoAUTO.

Flipthelightswitchoforone

second then back on to toggle

betweenAUTOandMANUAL

MODE.

Manualmodeworksonlywith

theON-TIMEswitchinthe1,

5,or10position.

21 m

(70 ft.)

2.4 m

(8 ft.)

Maximum

Maximum Range Coverage Angle*

(Side View) (Top View)

MANUAL MODE

AUTO

TEST

ON-TIME Switch at 1, 5,

or 10 minutes

MODE SWITCHING SUMMARY

Flip light switch

o for one second

then back on*

*Ifyougetconfusedwhileswitchingmodes,turn

thepoweroforoneminute,thenbackon.After

thecalibrationtimethecontrolwillbeintheAUTO

mode.

4. Loosen the clamp

screw in the sensor

ball joint and gently

rotatethesensor.

5. Walk through the

coverage area noting

where you are when

thelightsturnon(also,

the LED will ash

several times when

motionisdetected).

In 

TESTmode,lightwill

stayonfor5secondsaf-

termotionhasstopped

and then turn off.



Movethesensorhead

up,down,orsideways

tochangethecoverage

area.Keep the sensor

at least 2.5 cm (1") away from the lamp heads.

6. AdjusttheRANGEasneeded.RANGEset

toohighmayincreasefalsetriggeringdueto

heatsourcesinthecoveragearea(seeTrouble-

shootingsection).

7. Securethesensorheadbytighteningtheclamp

screw.Do not overtighten the screw.

8. SettheamountofON-TIMEyouwantthe

lighttostayonaftermotionisdetected(1,5,

or10minutes).etimerwillresetaslong

asthereismotionpresent.Oncemotionhas

stopped, the timer will time-out after the

selectedamountoftime.

Clamp

Screw

Ball

Joint

Aim Sensor Down

for Short Coverage

Aim Sensor Higher

for Long Coverage

180°

201115-01

SPECIFICATIONS

Range...................................... Upto21m(70ft.)[varieswithsurroundingtemperature]

SensingAngle.......................... Upto180°

ElectricalLoad........................ 111mA;14.3Watts(Typical)

PowerRequirements................ 230VAC,50Hz

OperatingModes.................... TEST,AUTO,andMANUALMODE

ON-Timer............................... 1,5,10minutes

TestTimer............................... 5Seconds

ManualModeTimer............... Dusk-to-Dawn

IngressProtection.................... IP43

SYMPTOM POSSIBLE CAUSE SOLUTION

Lightwillnotcome

on.

1. Lightswitchisturnedo.

2. Fuseisblownorcircuitbreakeristurnedo.

3. Daylightturn-oisineect.

4. Incorrectcircuitwiring,ifthisisanewinstallation.

5. Lightcontrolaimedinwrongdirection.

1. Turnlightswitchon.

2. Replacefuseorturncircuitbreakeron.

3. Recheckafterdark.

4. Verifywiringiscorrect.

5. Re-aimlightcontroltocoverdesiredarea.

Lightcomesonin

daylight.

1. Light control may be installed in a relatively dark

location.

2. LightcontrolisinTEST.

1. e xture is operating normally under these

conditions.

2. SetON-TIMEswitchto1,5,or10minutes.

Lightcomesonfor

noapparentreason.

1. Lightcontrolmaybesensingsmallanimalsorautomobile

trac.

2. Rangeissettoohigh.

1. Re-aimsensor.Reducerange.

2. Reducerange.

Lightstayson

continuously.

1. A lamp head is positioned to close to the sensor or

pointedatnearbyobjectsthatcauseheattotriggerthe

sensor.

2. esensormaybepickingupaheatsourcelikeanair

vent, dryer vent, or brightly painted, heat-reective

surface.

3. LightcontrolisinManualmode.

4. Sensitivityissettoohigh.

1. Repositionthelampheadawayfromthesensoror

nearbyobjects.

2. Re-aimsensor.Reducerange.

3. SwitchtoAuto.

4. Reducerange.

Lightasheson

ando.

1. Heatorlightfromthelampheadsmaybeturningthe

lightcontrolonando.

2. LightcontrolisintheTESTmodeandwarmingup.

3. Heatbeingreectedfromotherobjectsmaybeaecting

thesensor.

1. Repositionthelampheadsawayfromthesensor.

2. Flashingisnormalundertheseconditions.

3. Re-aimsensor.Reducerange.

Lights flash once,

thenstayoinman-

ualmode.

Lightcontrolisdetectingitsownlights. Reposition lamp heads to keep area below the light

controlrelativelydark.

TROUBLESHOOTING GUIDE

eChamberlainGroupreservestherighttodiscontinueproductsandtochangespecicationsat

anytimewithoutincurringanyobligationtoincorporatenewfeaturesinproductspreviouslysold.

8201115-01

CHAMBERLAIN LIMITED WARRANTY

Lighting and Chime Products

ChamberlainAustraliaPtyLimited/ChamberlainNewZealand Limited(Chamberlain)iscommittedto manufacturingandsupplyinghighqualitygoods.As

partofthiscommitment,weseektoprovidereliableserviceandsupportforourgoodsandarepleasedtoprovideyou,theoriginalpurchaser,withthisChamberlain

LimitedWarranty.

WealsoprovidethefollowingstatementasrequiredbytheAustralianConsumerLaw:InAustralia,inadditiontoyourrightsunderthisChamberlainLimitedWar-

ranty,ourgoodscomewithguaranteesthatcannotbeexcludedundertheAustralianConsumerLaw.Youareentitledtoareplacementorrefundforamajorfailureand

forcompensationforanyotherreasonablyforeseeablelossordamage.Youarealsoentitledtohavethegoodsrepairedorreplacedifthegoodsfailtobeofacceptable

qualityandthefailuredoesnotamounttoamajorfailure.

Chamberlain’s warranty

Chamberlainwarrantstotheoriginalpurchaserofthelightingorchimeproduct(includinganyLEDlightswhichareprovidedbyChamberlainaspartofthegoods)

(Unit)thattheUnitisfreefromdefectsinmaterialsandworkmanshipforaperiodof12monthsfromthedateofpurchase.

DuringtheapplicableChamberlainLimitedWarrantyperiod,ifyouareconcernedthattheUnitmaybedefective,contactyourretailerwhowillprovideyouwitha

replacementUnitorreferyoutoourservicecentreforafactoryrepairorreplacement.

Ifyourretailerrefersyoutous,callourservicecentreonthetollfreenumberbelowandaChamberlaintechnicianwilldiagnosetheproblem.Oncetheproblemhas

beendiagnosed,subjecttoyourrightsundertheAustralianConsumerLawwithrespecttomajorfailures,Chamberlainwillprovideyouwithshippinginstructions

forafactoryrepairorreplacement.

Ifafactoryrepairorreplacementisrequired,providedthedefectivepartorUnitisreturnedtoChamberlainwell-packagedandinaccordancewithChamberlain’s

shippinginstructions,Chamberlainwillrepairor,atitsoptionbutsubjecttoyourrightsundertheAustralianConsumerLawwithrespecttomajorfailures,replace

anydefectivepartorUnitandreturnittoyouatnocost.

RepairsandreplacementpartsprovidedunderthisChamberlainLimitedWarrantyareprovidedfreeofchargeandarewarrantedfortheremainingportionofthe

originalwarrantyperiod.

isChamberlainLimitedWarrantyprovidesbenetswhichareinadditiontoyourotherrightsandremediesasaconsumer.

Exclusions

Ifourservicecentredeterminesthatawarrantyclaimhasbeenmadeinrespectofafailureordefectarisingunderoroutofanyexclusiondetailedbelowsuchthatthe

claimisnotcoveredunderthisChamberlainLimitedWarranty,wemay,subjecttoyourotherrightsandremediesasaconsumer,chargeyouafeetorepair,replace

and/orreturntheUnittoyou.

Exclusions

isChamberlainLimitedWarrantydoesnotcoveranyfailureof,ordefectin,theUnitdueto:

1. non-compliancewiththeinstructionsregardinginstallation,operation,maintenanceandtestingoftheUnitorofanyproductwithwhichtheUnitisused;

2. anyattemptbyapersonotherthananauthorisedinstallertorepair,dismantle,reinstallormovetheUnittoanotherlocationonceithasbeeninstalled;

3. tampering,neglect,abuse,wearandtear,accident,electricalstorm,excessiveuseorconditionsotherthannormaldomesticuse;

4. problemscausedbyelectricalfaultsorreplacementofbatteriesorlightbulbs;

5. submersioninwaterorotheruids;

6. powersupplygreaterorlessthanwhatisspecied;

7. useofalightbulbwithahigherwattagethanthatspecied;or

8. forchimesproducts,radiointerferencefromanotherradiofrequencyappliance.

IfthisChamberlainLimitedWarrantydoesnotapply,youmayhaverightsavailabletoyouundertheAustralianConsumerLaw.

Liability – Australia only

ExceptassetoutintheAustralianConsumerLaw(beingSchedule2ofthe

Competition and Consumer Act 2010

)(asamended,consolidatedorreplaced):

1. allotherguarantees,warrantiesandrepresentationsinrelationtotheUnitoritssupplyareexcludedtotheextentthatChamberlaincanlawfullyexcludethem;

and

2. undernocircumstanceswillChamberlainbeliableforconsequential,incidentalorspecialdamagesarisinginconnectionwiththeuse,orinabilitytouse,theUnit,

otherthanthosewhichwerereasonablyforeseeableasliabletoresultfromthefailure.

Liability – New Zealand only

Exceptassetoutinthe

Fair Trading Act 1986

andthe

Consumer Guarantees Act 1993

(asamended,consolidatedorreplaced):

and

otherthanthosewhichwerereasonablyforeseeableasliabletoresultfromthefailure.

Note

Werequestthatyouretainyoursalesdocketorinvoiceasproof-of-purchaseandattachittothismanualtoenableyoutoestablishthedateofpurchaseintheunlikely

eventofawarrantyservicebeingrequired.ChamberlainreservestherighttochangethedesignandspecicationsoftheUnitwithoutpriornotication.Somefeatures

oraccessoriesoftheUnitmaynotbeavailableincertainmarketsorareas.Pleasecheckwithyourretailer.

Chamberlain service centre contact details

Australia New Zealand

Phonetollfree1800638234 Aucklandphone094772823

Faxtollfree1800888121 Phonetollfree0800653667

Email:customerser[email protected] Faxtollfree0800653663

Chamberlain Australia Pty. Ltd. Chamberlain New Zealand Limited

Unit 3, 7-9 Orion Rd 17A Arrenway Drive, Albany

Lane Cove NSW 2066 Auckland

(P.O. Box 1446, Lane Cove, NSW 1595) (PO Box 100221 North Shore 0745)

Website

Secure Home SH-9910AU Installation And Operating Instructions Manual

Other documents