Edelbrock Performer Intake Manifold Small-Block Ford Operating instructions

Brand: Edelbrock

Model: Performer Intake Manifold Small-Block Ford

Type: Operating instructions

Catalog #2181, 3781, 3783, 7181, 7581

Rev A - . 2/12 - CP/mc

Brochure #63-0034Page 1 of 3

Performer and Performer RPM Intake Manifolds

For 351 c.i.d. Ford Windsor Engines

Catalog #s 2181, 3781, 3783, 7181, & 7581

INSTALLATION INSTRUCTIONS

PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and

procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this

installation, it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical

Hotline at: 1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday.

IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation

will void your warranty and may result in poor performance and engine or vehicle damage.

DESCRIPTION: Edelbrock Performer series intake manifolds are designed for engines operating in the idle to 5500 rpm range. Performer RPM

series intake manifolds are designed for engines operating in the 1500-6500 rpm range. Match Performer or Performer RPM intake manifolds

with recommended carburetors and additional equipment for even greater performance increases.

APPLICATIONS:

INTAKE MANIFOLD REFERENCE APPLICATION

2181 B, C, D, E, F Performer 351W: Designed for street 351 c.i.d. Ford Windsor V8s without EGR. Choke

block-off plate #8981 included.

3781, 3783 B, D, E, F Performer 351 2-V (3781) and Performer 351 4-V H.O. (3783) - Designed for carbureted

351 c.i.d. Ford Windsor V8s with EGR. 3781 includes a 2-bbl EGR plate, allowing the use

of the stock 2-bbl carburetor and EGR valve. 3783 replaces the stock 4V EGR manifold

using the stock 4v EGR adapter. Includes provision for EFE valve on H.O. engines. Both

manifolds can be adapted for 4-bbl use by using our #8053 4V EGR plate and the OEM

EGR valve and gasket. Choke block-off plate #8981 included.

7181 B, C, D, E, F Performer RPM 351W: Designed for 1969 and later 351 c.i.d. Ford Windsor V8s with

Edelbrock Performer RPM cylinder heads, modified OEM cylinder heads, or equivalent.

No provision for exhaust heated choke or rear water crossover. Choke block-off plate

#8981 included.

7581 A, C, D, F RPM Air-Gap 351W: Designed for 1969 and later 351 c.i.d. Ford Windsor V8s with

Edelbrock Performer RPM cylinder heads, modified OEM cylinder heads, or equivalent.

Features an Air-Gap design, resulting in a cooler, denser charge for more power.

Features a larger cross sectional area and taller carb flange for compatibility with large

displacement 351W based stroker engines. No provisions for exhaust heated chokes

and no exhaust crossover. Will not fit stock hood.

A- Not legal for sale or use on pollution controlled motor vehicles.

B- Stock replacement/street legal in some applications. See “Stock Replacement Parts List for Intake Manifolds” insert, or Catalog for details.

C- Available in additional finishes, such as polished, black, or EnduraShine. See Catalog for details.

D- Aftermarket 4-bbl carburetors are not compatible with Ford AOD. Performer Series and Thunder Series AVS carbs will work with Ford AOD

when used with Lokar bracket SRK-4000, for more info call (865) 966-2269 or go to www.lokar.com

E- Will fit 1964-1/2 - 1970 Mustangs. Will not fit under stock hood of 1974-1978, or 1979-1995 Mustangs.

F- Will fit early 16 bolt heads when used with Ford 16 bolt intake gasket set. For van installations use Ford “van” intake gasket set.

•EGR SYSTEMS: Edelbrock EGR-equipped

Performer

manifolds are intended as a direct functionally identical replacement for their O.E.M.

counterparts. All exhaust emissions or emissions related stock components are intended to be retained and functional. Non-EGR equipped

manifolds will not accept stock EGR (Exhaust Gas Recirculation) equipment. EGR systems are used on most 1972 and later model vehicles.

Check local laws for requirements.

Catalog #2181, 3781, 3783, 7181, 7581

Rev A - . 2/12 - CP/mc

Brochure #63-0034Page 2 of 3

•ACCESSORIES & INSTALLATION ITEMS: Major recommendations are listed below. See our catalog for details. To order a catalog, call

(800) FUN-TEAM, or visit www.edelbrock.com.

•THROTTLE BRACKETS: Due to the design of Performer manifolds, the throttle and kickdown bracket on some vehicles may require

modification to fit. When using Edelbrock carburetors, use #1491 or 1846 throttle plate kit.

•GASKETS: Do not use competition style intake gaskets for this street manifold. Due to material deterioration over time, internal leakage of

vacuum, oil, and coolant may occur.

A-Carburetor will work with non-EGR or pre-emission control systems.

B-Carburetor will work with EGR system.

H-Carburetor has provision for evaporative canister.

I-Carburetor has no provisions for evaporative canister.

K-Carburetor requires #8008 or #8024 stud, washer and nut kit. Determine proper length based on gasket thickness and your accessory

mounting requirements.

N-Carburetor accepts factory cruise control

O-Carburetor comes with manual choke. It can be converted to electric choke using kit #1478.

P-Carburetor is not a stock replacement part

CARBURETOR REFERENCE PARTS REQUIRED FOR INSTALLATION

Performer #1405 (600 cfm) A, I, K, N, O #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Performer #1406 (600 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Thunder Series #1805 (650 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Thunder Series #1806 (650 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Thunder Series #1825 (650 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Thunder Series #1826 (650 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

CARBURETOR REFERENCE PARTS REQUIRED FOR INSTALLATION

Performer #1407 (750 cfm) A, I, K, N, O #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Performer #1411 (750 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Performer #1412 (800 cfm) A, I, K, N, O #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Performer #1413 (800 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Thunder Series #1812 (800 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

Thunder Series #1813 (800 cfm) A, I, K, N #1491 or 1846 throttle plate kit, #1483 or 1844 throttle lever adapter

INTAKE MANIFOLD REFERENCE RECOMMENDED GASKET

2181, 3781, 3783, 7181, 7581 Edelbrock #7220 Port: 1.20” x 2.00”, .060” Thickness

NOTE: To ensure maximum performance and a proper seal, Edelbrock gaskets which are

specifically designed and manufactured for use with Edelbrock parts must be used.

CARBURETOR REFERENCE PARTS REQUIRED FOR INSTALLATION

OEM B, H, N

Manifold 2181 (Non-Emissions):

Manifold 7181, 7581 (Non-Emissions):

•CARBURETOR RECOMMENDATIONS:

Manifold 2181, 3781, 3783 (Emissions Controlled Applications):

Catalog #2181, 3781, 3783, 7181, 7581

Rev A - . 2/12 - CP/mc

Brochure #63-0034Page 3 of 3

INSTALLATION INSTRUCTIONS

1) Use only recommended intake gaskets set when installing this intake manifold.

2) Fully clean the cylinder head intake flanges and the engine block end seal surfaces.

3) Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of the gaskets, allow to

air dry, and attach the intake gaskets.

4) Do not use cork or rubber end seals. Use RTV silicone sealer instead. Apply a ¼" high bead across each block end seal surface,

overlapping the intake gasket at the four corners. This method will eliminate end seal slippage.

5) Install the intake manifold and hold-down bolts. Torque all of the manifold bolts in two steps by the sequence shown in Figure 2 to

18-20 ft/lbs.

•PREP AND TUNING FOR POWER:

NOTE: Local emission laws must be checked for legality of any carburetor or ignition changes.

Performer Series Intake Manifolds

1. The long equal length runners in the Performer manifold create a very strong signal to the carburetor. In some applications, the stock

rods or jets may need changing for best overall performance. Refer to your carburetor owner's manual for details.

2) Performer manifolds deliver excellent drivability and power utilizing stock distributor settings. Some applications may benefit from

resetting the initial advance ±2° from the factory specification.

3) Aftermarket ignitions and more aggressive advance curves may be used with Performer packages.

4) Installation of aftermarket headers or camshafts may lean the carburetor calibration. Should this occur recalibrate with a richer jet.

Performer RPM Series Intake Manifolds

1. Due to design, the fuel / air mixture and cylinder charging are very efficient with Performer RPM or RPM Air-Gap manifolds. Generally

speaking, the stock jetting for a Performer Series or Thunder Series carburetor will not need changing. Specific applications may show

an increase in power by tuning the fuel mixture.

2. Aftermarket distributor curve kits may be used with Performer RPM series manifolds.

3. Use modified or high performance cylinder heads such as our Performer RPM, and port-match the manifold to the heads.

4. The compression ratio should be at least 9.5 to 1 to work properly with Performer RPM camshafts.

5. Installation of aftermarket headers, camshafts or both with an Edelbrock Performer RPM series manifold may lean carburetor calibration.

Should this condition occur, recalibrate with a richer jet.

•CAMSHAFT AND HEADERS: The Performer Series manifolds are compatible with aftermarket camshafts and headers designed to work in

the idle-5500 rpm range. Edelbrock has developed a dyno-matched, street proven camshaft #2182, for use with Performer Series intake

manifolds. Header primary tube diameter should be 1-5/8". Performer RPM Series manifolds are compatible with aftermarket camshafts and

headers designed to work in the 1500-6500 rpm range. Edelbrock has developed a dyno-matched, street-proven camshaft #7182 for use

with Performer RPM series manifolds (see catalog for details). Header primary tube diameter should be 1-3/4".

Figure 1 - 351W Ford Torque Sequence

Torque Bolts to 18-20 ft/lbs.

Firing Order: 1-3-7-2-6-5-4-8

Turn Distributor Clockwise to Advance Ignition Timing

Edelbrock Corporation • 2700 California St. • Torrance, CA 90503

Tech Line: 800-416-8628

Edelbrock Performer Intake Manifold Small-Block Ford Operating instructions

Edelbrock Performer Intake Manifold Small-Block Ford Operating instructions

Edelbrock Performer Intake Manifold Small-Block Ford Operating instructions

Related papers

Other documents