Scosche TA2043B User manual

TA2043B
Scosche
Brand
Scosche
Model
TA2043B
Category
Car kits
Type
User manual

Scosche TA2043B is a car stereo installation kit designed to fit 2003 and up Toyota Sequoia and Tundra vehicles. It allows for the installation of a Double ISO/DIN style radio. The kit includes a pocket, rear mounting bracket, trim ring, and all necessary hardware. Detailed instructions are provided to guide the user through the removal of the factory radio and the installation of the new radio using the kit components. The instructions emphasize safety precautions, including disconnecting the vehicle's negative battery terminal before installation and avoiding all factory airbag wiring.

Scosche TA2043B is a car stereo installation kit designed to fit 2003 and up Toyota Sequoia and Tundra vehicles. It allows for the installation of a Double ISO/DIN style radio. The kit includes a pocket, rear mounting bracket, trim ring, and all necessary hardware. Detailed instructions are provided to guide the user through the removal of the factory radio and the installation of the new radio using the kit components. The instructions emphasize safety precautions, including disconnecting the vehicle's negative battery terminal before installation and avoiding all factory airbag wiring.

A
B
© 2007 SCOSCHE INDUSTRIES, INC.
SI 03/07 - TA2043 (3000465)
If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3
TA2043
IN-DASH INSTALLATION KIT FOR
2003-UP TOYOTA SEQUOIA/TUNDRA VEHICLES
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash
disassembly, wire harness/codes and information pertaining to installation of this kit (TA2043) in
2003-UP Toyota Sequoia/Tundra Vehicles. Scosche Industries, Inc. can not be held responsible for
discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or
options, or damage that may occur in the automobile during the installation of components while
using this booklet.
For Factory Wiring Codes go to: www.scosche-cars.com
FACTORY WIRING CODES
5455
TRIM RING
5125 POCKET
5447
KIT PANEL
5324 REAR
MOUNTING
SUPPORT
Thank you for purchasing the Scosche TA2043 Kit. This kit was manufactured with the highest of quality
standards.
CAUTION:
DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLA-
TION TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/
OHM METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE
PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S COMPUTER AND/OR DIAGNOSTIC
SYSTEMS. AVOID ALL FACTORY AIR BAG WIRING - AIR BAGS CAN ACCIDENTALLY DEPLOY
CAUSING SERIOUS INJURY OR DEATH.
NOTES:
• See your vehicle's instructions for any special tools your installation might require.
• Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting
instructions.
INTRODUCTION / PRELIMINARY
A. ATTACHING THE REAR
BRACKET:
Align the two (2) screw
emboss locations to the
matching locations on
pocket. When aligned, slide
the bracket together. Screw
the two (2) supplied screws
to screw emboss locations
B. ATTACHING THE POCKET:
Align the pocket to the snaps
of kit panel. Snap the pocket
into place on the back of kit
panel.
2003-Up Toyota Sequoia
RADIO REMOVAL AND IN-DASH INSTALLATION
NOTE: The Factory radio provision is for a Double ISO/DIN style radio.
1. Extract (1) Phillips screw from each air vent in radio dash bezel.
2. Using panel removal tool, pry off radio bezel, pull away, unplug and remove.
3. Extract (4) 10 mm bolts securing radio, pull away, unplug, and remove.
2003-Up Toyota Tundra
RADIO REMOVAL AND IN-DASH INSTALLATION
1. Extract (2) Phillips screws in vents.
2. Remove (3) AC control knobs. Remove (3) Phillips screws from behind.
3. Using panel removal tool, pop out dash that covers AC controls and radio.
4. Extract (4) 10 mm bolts from radio brackets, disconnect and remove.
TA2043 KIT
5324
REAR
MOUNTING
SUPPORT
BRACKET
DIN
MOUNT
RADIO
5447 KIT PANEL
5125 POCKET
5324 REAR MOUNTING BRACKET
POCKET ASSEMBLY
STEREO INSTALLATION
MOUNTING THE RADIO
CAUTION:
REAR SUPPORTING THE
RADIO ADDS TO THE
INSTALLATIONS
STRUCTURAL INTEGRITY.
RADIO’S
MOUNTING
SLEEVE
BEND TABS
OUTWARD
TRIM
RING
  • Page 1 1

Scosche TA2043B User manual

TA2043B
Scosche
Brand
Scosche
Model
TA2043B
Category
Car kits
Type
User manual

Scosche TA2043B is a car stereo installation kit designed to fit 2003 and up Toyota Sequoia and Tundra vehicles. It allows for the installation of a Double ISO/DIN style radio. The kit includes a pocket, rear mounting bracket, trim ring, and all necessary hardware. Detailed instructions are provided to guide the user through the removal of the factory radio and the installation of the new radio using the kit components. The instructions emphasize safety precautions, including disconnecting the vehicle's negative battery terminal before installation and avoiding all factory airbag wiring.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents