Metra 88-00-8000 Operating instructions

Brand: Metra

Model: 88-00-8000

Type: Operating instructions

METRA. The World’s best kits.

™

metraonline.com

REV. 2/1/2016 INST88-00-8000

Installation instructions for part 88-00-8000

• Pocket provision for ISO DIN radio installations

• Holds (3) CD jewel cases

• A) Pocket

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Please visit metraonline.com for options

Antenna Adapter: • Not required

• Panel removal tool • Phillips screwdriver • 10mm socket wrench

TOOLS REQUIRED

Toyota ISO Pocket 1981-2004

88-00-8000

APPLICATIONS

See application list inside cover

Table of Contents

Dash Disassembly 2-11

TOYOTA

4-Runner 1984-1988 2

4-Runner 1989-1995 2

4-Runner 1996-2002 3

Camry 1983-1986 3

Camry 1987-1991 3

Celica 1982-1985 4

Celica 1986-1989

Celica 1990-1993 4

Corolla (coupe/

hatchback)

1982-1983 5

Corolla 1984-1987 5

Corolla (coupe/

hatchback)

1988-1992 5

Corolla (sedan/wagon-

lower dash)

1988-1992 6

Corolla (sedan/wagon-

upper dash)

1988-1992 6

TOYOTA (Continued)

Corolla (lower dash)

1993-1997 6

Corolla (upper dash)

1993-1997 7

Land Cruiser

1988-1992 7

MR2 1985-1990 7

MR2 1991-1995 8

Paseo 1992-1995 8

Paseo 1996-1997 8

Pickup 1984-1988 9

Pickup 1989-1995 9

Supra 1983-1986 9

Supra 1986.5-1992 10

T-100 1993-1998 10

Tacoma 1995-2004 10

Tercel 1987-1990 11

Tercel 1991-1994 11

Tercel 1995-1998 11

Kit Assembly 12

88-00-8000

Applications Dash Disassembly

(Figure A)

4-Runner 1984-1988

1. Remove the ashtray and (3) screws

from the ashtray bracket. Remove

(1) screw from each side of the

dash console and unsnap the trim

bezel. (Figure A)

Continue to kit assembly

4-Runner 1989-1995

Remove the driver’s side speaker panel by

removing (3) screws and (1) 10mm bolt.

Remove (1) screw from the left side of the

housing and unsnap the ignition cover. Remove

the glove compartment assembly by removing

(1) 10mm bolt from the bottom of the speaker

panel and (3) screws from the right side of the

housing. Remove the remaining (3) screws

securing the radio trim bezel. (Figure A)

Continue to kit assembly

TOYOTA

4-Runner 1984-2002

Avalon* 1995-1999

Camry 1983-1991

Camry* 1992-2001

Camry Solara* 1999-2003

Celica 1982-1993

Celica* 1994-1999

Corolla (coupe/

hatchback) 1982-1983

Corolla 1984-1997

Cressida* 1981-1992

Land Cruiser

(without nav)* 2000-2002

Land Cruiser* 1993-1999

Land Cruiser 1988-1992

TOYOTA (Continued)

MR2 1985-1995

Paseo 1992-1997

Pickup 1984-1995

Previa* 1991-1997

Rav-4* 1996-2000

Sequoia* 2001-2002

Sienna* 1996-2003

Supra 1983-1992

Supra* 1994-1998

T-100 1993-1998

Tacoma 1995-2004

Tercel* 1983-1986

Tercel 1987-1998

Tundra* 2000-2002

Van* 1984-1990

* No dash disassembly available

CAUTION!

All accessories, switches, climate controls panels, and especially air bag indica

tor lights must be connected before cycling the ignition. Also, do not remove the factory

radio with the key in the on position, or the vehicle running.

88-00-8000

Dash Disassembly

(Figure A)

(Figure A)(Figure A)

4-Runner 1996-2002

Open the center armrest door. Unsnap the parking

brake trim panel to access the gear shifter trim panel.

Unsnap the gear shifter trim panel and remove.

Remove the climate control knobs. Remove the climate

control trim plate and (2) Phillips screws exposed.

Unclip the radio trim bezel and remove. Remove

(4) Phillips screws securing the factory radio and

disconnect the wiring. (Figure A)

Continue to kit assembly

Camry 1987-1991

Remove (2) screws above the climate controls

and gently unsnap the dash trim bezel. Remove

(4) screws securing the factory radio and

disconnect the wiring. (Figure A)

Continue to kit assembly

Camry 1983-1986

Remove (3) Phillips screws above the climate

controls. Remove (2) Phillips screws from the

left side of the dash trim bezel and remove the

bezel. Remove the screws securing the factory

radio and disconnect the wiring

. (Figure A)

Continue to kit assembly

88-00-8000

Dash Disassembly

(Figure A)(Figure A)

Celica 1986-1989

Remove (2) screws from the lower steering column

panel and remove the panel. Remove (2) screws

exposed on the dash trim bezel. Open the glove

box and remove (2) screws exposed. Remove (2)

screws from the ashtray cavity and (2) screws

from the bracket. Remove (2) screws from each

side of the dash trim bezel and unclip the bezel.

Remove the screws securing the factory radio and

disconnect the wiring. (Figure A

)

Continue to kit assembly

Celica 1982-1985

Remove the ashtray and the climate control knobs.

Remove (3) flat-head screws from the climate

control panel and remove the panel. Remove (2)

Phillips screws from the top edge of the radio trim

bezel. Remove (4) Phillips screws from the base of

the radio trim bezel and remove the bezel. Remove

(4) Phillips screws from the factory radio and

disconnect the wiring. (Figure A

)

Continue to kit assembly

(Figure A)

Celica 1990-1993

Carefully pry up on the gear shifter trim panel

and remove. Remove (2) screws exposed on the

bottom edge of the radio trim panel. Unsnap the

panel and disconnect the ashtray and cigarette

lighter wiring. (Figure A

)

Continue to kit assembly

88-00-8000

Dash Disassembly

(Figure A) (Figure A)(Figure A)

Corolla 1984-1987

Remove (2) Phillips screws from each side of the

console trim bezel. Remove (4) screws securing

the factory radio and disconnect the wiring.

(Figure A)

Continue to kit assembly

Corolla (coupe/hatchback) 1988-1992

Remove (2) Phillips screws from each side of the

console trim bezel. Remove (4) screws securing

the factory radio and disconnect the wiring.

(Figure A)

Continue to kit assembly

Corolla (coupe/hatchback) 1982-1983

Remove (2) screws from each side of the dash trim

bezel and remove the bezel. Remove (4) screws

securing the upper radio dummy cover to the bezel

and remove. (Figure A)

Continue to kit assembly

88-00-8000

Dash Disassembly

(Figure A)

Corolla (sedan/wagon-lower dash) 1988-1992

Remove (1) screw located to the right of the

ignition switch. Remove (1) screw located above

the driver’s side speaker. Carefully unsnap the

dash trim bezel (some force may be required).

(Figure A)

Continue to kit assembly

(Figure A)

Corolla (sedan/wagon-upper dash) 1988-1992

Remove (4) screws from the top edge of the

instrument trim bezel and (2) screws below the

radio opening. Remove (1) screw from the lower-

left tab of the bezel (to the right of the a/c vent)

and unsnap the bezel. (Figure A)

Continue to kit assembly

Corolla (lower dash) 1993-1997

Remove the climate control knobs, unsnap the

upper trim bezel and disconnect the hazard and

clock leads. Remove (2) screws from the lower

trim bezel and remove. (Figure A)

Continue to kit assembly

(Figure A)

88-00-8000

Dash Disassembly

Land Cruiser 1988-1992

Remove (3) screws from the lower edge of the

climate control panel. Remove (8) screws from the

perimeter of the dash trim bezel. Pull out on the

lower edge of the bezel and remove. Remove the

screws securing the factory radio and disconnect

the wiring. (Figure A)

Continue to kit assembly

(Figure A)

Corolla (upper dash) 1993-1997

Remove the climate control knobs and unsnap the

dash trim bezel. Disconnect the clock and hazard

leads. (Figure A)

Continue to kit assembly

(Figure A)

MR2 1985-1990

Remove (2) screws from the top of the dash trim

bezel and remove the bezel. Remove (4) screws

from the factory radio (or coin tray dummy panel)

and disconnect the wiring. (Figure A)

Continue to kit assembly

88-00-8000

Dash Disassembly

(Figure A)

Paseo 1996-1997

Unclip the bottom of the radio trim bezel. Unhook

the top of the radio trim bezel and remove the

bezel. Remove (4) 8mm Phillips screws securing

the factory radio and disconnect the wiring.

(Figure A)

Continue to kit assembly

(Figure A) (Figure A)

MR2 1991-1995

Remove the ashtray and (2) screws from the

ashtray cavity. Unsnap and remove the shifter

console bezel. Remove (1) screw below the

ignition switch and remove the dash trim bezel.

(Figure A)

Continue to kit assembly

Paseo 1992-1995

Pry up on the radio trim bezel and remove.

Remove (4) Phillips screws securing the factory

radio and disconnect the wiring. Remove the

screws securing the factory cupholder to the

assembly and remove. Remove the screws

securing the factory ashtray/cigarette lighter to the

assembly and remove. (Figure A)

Continue to kit assembly

88-00-8000

Dash Disassembly

(Figure A)

Pickup 1984-1988

Remove the ashtray and (3) screws from

the ashtray bracket. Remove (1) screw

from each side of the dash console and

unsnap the trim bezel. (Figure A)

Continue to kit assembly

(Figure A)

Pickup 1989-1995

Remove the driver’s side speaker panel by removing (3) screws and (1)

10mm bolt

Remove (1) screw from the left side of the housing and unsnap the

ignition cover

Remove the glove compartment assembly by removing (1) 10mm bolt

from the bottom of the speaker panel and (3) screws from the right

side of the housing.

Remove the remaining (3) screws securing the radio trim bezel. (Figure A)

Continue to kit assembly

(Figure A)

Supra 1983-1986

Remove the ashtray and the climate

control knobs. Remove (3) flat-head

screws from the climate control panel

and remove the panel. Remove (2)

Phillips screws from the top edge of

the radio trim bezel. Remove (4) Phillips

screws from the base of the radio trim

bezel and remove the bezel. Remove (4)

Phillips screws from the factory radio and

disconnect the wiring. (Figure A

)

Continue to kit assembly

88-00-8000

Dash Disassembly

(Figure A)

Supra 1986.5-1992

Remove the ashtray and (2) screws from the

ashtray cavity

Remove (1) screw located to the right of the

steering column and (1) screw located to the left

of the gear shifter. (Figure A)

Continue to kit assembly

(Figure A) (Figure A)

T-100 1993-1998

1. Pull the cupholder out and unsnap the trim bezel

from the dash. (Figure A)

2. Remove (4) screws securing the factory radio and

disconnect the wiring.

Continue to kit assembly

Tacoma 1995-2004

1. Remove the climate control knobs.

2. Unsnap the climate control trim panel and

remove (2) screws exposed. (Figure A)

3. Gently unclip the dash trim bezel, lift up on the

panel and remove.

Continue to kit assembly

88-00-8000

Dash Disassembly

(Figure A) (Figure A) (Figure A)

Tercel 1987-1990

Remove (1) Phillips screw located above the

ignition switch. Remove the climate control

knobs. Unclip the dash trim bezel and remove.

Remove (4) Phillips screws securing the

factory radio assembly and disconnect the

wiring. Remove (2) screws securing the factory

cupholder to the assembly and remove. Remove

(4) screws securing the ashtray/cigarette lighter

to the assembly and remove. (Figure A)

Continue to kit assembly

Tercel 1991-1994

Pry up on the radio trim bezel and remove.

Remove (4) Phillips screws securing the factory

radio and disconnect the wiring. Remove the

screws securing the factory cupholder to the

assembly and remove. Remove the screws

securing the factory ashtray/cigarette lighter to

the assembly and remove. (Figure A)

Continue to kit assembly

Tercel 1995-1998

Unclip the bottom of the radio trim bezel. Unhook

the top of the radio trim bezel and remove the

bezel. Remove (4) 8mm Phillips screws securing

the factory radio and disconnect the wiring.

(Figure A)

Continue to kit assembly

METRA. The World’s best kits.

™

metraonline.com

REV. 2/1/2016 INST88-00-8000

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians

Installation instructions for part 88-00-8000

IMPORTANT

If you are having difficulties with the

installation of this product, please call our

Tech Support line at 1-800-253-TECH.

Before doing so, look over the instructions a

second time, and make sure the installation

was performed exactly as the instructions

are stated. Please have the vehicle apart

and ready to perform troubleshooting steps

before calling.

(Figure A)

1. Remove the mounting brackets from the

factory radio assembly.

2. Align the holes in the factory mounting

brackets with the holes in the pocket, and

then secure with the (4) screws removed in

dash disassembly. (Figure A)

3. Remove the metal DIN sleeve and trim ring

from the aftermarket radio.

4. Slide the radio in the bracket/pocket

assembly using the (4) screws supplied with

the radio.

5. Locate the factory wiring harness and

antenna connector in the dash, and

complete all necessary connections to the

radio. Metra recommends using the proper

mating adapter from Metra and/or AXXESS.

Re-connect the negative battery terminal

and test the radio for proper operation.

6. Reassemble the dash in reverse order of

disassembly

Kit Assembly

Page is loading ...

Metra 88-00-8000 Operating instructions

Brand: Metra

Model: 88-00-8000

Type: Operating instructions

Download PDF

report

in other languages

español: Metra 88-00-8000 Instrucciones de operación

Metra 88-00-8000 Operating instructions

Metra 88-00-8000 Operating instructions

in other languages

Related papers

Other documents