ACTi E62 User manual

www.acti.com

Encoder Firmware V4.06.09 User’s Manual

1

Firmware User’s Manual

A1D-500-V6.04.15-AC

2013/09/04

www.acti.com

Firmware User’s Manual V6.04.15

2

Table of Contents

Recommended PC Specifications 4

Preparation 5

Connect the Equipment ............................................................................. 5

Configure the IP Addresses ....................................................................... 5

Access the Camera ..................................................................................... 9

Live View 11

Login .......................................................................................................... 11

Live View ................................................................................................... 12

ePTZ View Mode................................................................................... 15

Panorama View Mode ........................................................................... 15

Fisheye View Mode ............................................................................... 16

Setup 17

Access the Setup Page ............................................................................ 17

Host ............................................................................................................ 18

Date & Time ............................................................................................... 19

Network ..................................................................................................... 21

IP Address Filtering ............................................................................... 21

Port Mapping ......................................................................................... 23

HTTPS .................................................................................................. 24

IEEE 802.1X ......................................................................................... 25

SNMP Setting ....................................................................................... 27

RTP ....................................................................................................... 29

Network (ToS, UPnP, Bonjour, ONVIF) ................................................. 30

IP Settings ................................................................................................. 33

Connection Type ................................................................................... 33

www.acti.com

Firmware User’s Manual V6.04.15

3

DNS ...................................................................................................... 35

DDNS .................................................................................................... 36

Video .......................................................................................................... 39

Compression ......................................................................................... 41

Motion Detection ................................................................................... 44

Day/Night .............................................................................................. 49

Image .................................................................................................... 50

Exposure / White Balance ..................................................................... 51

OSD/Privacy Mask ................................................................................ 55

On-Screen Graphics ............................................................................. 58

Audio ..................................................................................................... 60

Event .......................................................................................................... 61

Event Server ......................................................................................... 61

Event Configuration .............................................................................. 64

Event List .............................................................................................. 70

Manual Event ........................................................................................ 73

Local Storage Management ..................................................................... 74

Status .................................................................................................... 75

Utilities .................................................................................................. 76

Setup..................................................................................................... 81

File Management .................................................................................. 82

Event Handler with Local Storage ........................................................... 88

System ....................................................................................................... 95

User Account ......................................................................................... 95

System Info ........................................................................................... 96

Factory Default ...................................................................................... 97

Firmware Upload ................................................................................... 98

Save & Reboot ...................................................................................... 99

Logout ..................................................................................................... 100

Troubleshooting 101

www.acti.com

Firmware User’s Manual V6.04.15

4

Recommended PC Specifications

In order to configure or test the cameras, a PC with following basic specifications is needed:

CPU

Core2Duo 2.13GHz or above

Memory

2 GB or above

Operating System

 Windows XP with SP2 or above.

 Windows 2003

 Windows Vista

 Windows 2008

 Windows 7

Browser for Accessing

Firmware

 Internet Explorer 8.0 or newer (full functionality)

 Other browsers with VLC installed (partial functionality)

Video Resolution

1024x768 or higher

www.acti.com

Firmware User’s Manual V6.04.15

5

Preparation

Connect the Equipment

To be able to connect to the camera firmware from your PC, both the camera and the PC have to

be connected to each other via Ethernet cable. At the same time, the camera has to have its own

power supply. In case of PoE cameras, you can use a PoE Injector or a PoE Switch between the

camera and the PC. The cameras that have the DC power connectors may be powered on by

using a power adaptor.

The Ethernet port LED or Power LED of the camera will indicate that the power supply for the

camera works normally.

Configure the IP Addresses

In order to be able to communicate with the camera from your PC, both the camera and the PC

have to be within the same network segment. In most cases, it means that they both should have

very similar IP addresses, where only the last number of the IP address is different from each

other. There are 2 different approaches to IP Address management in Local Area Networks – by

DHCP Server or Manually.

Using DHCP server to assign IP addresses:

If you have connected the computer and the camera into the network that has a DHCP server

running, then you do not need to configure the IP addresses at all – both the camera and the PC

would request a unique IP address from DHCP server automatically. In such case, the camera

will immediately be ready for the access from the PC. The user, however, might not know the IP

address of the camera yet. It is necessary to know the IP address of the camera in other to be

able to access it by using a Web browser.

The quickest way to discover the cameras in the network is to use the simplest network

search, built in the Windows system – just by pressing the “Network” icon, all the cameras of the

local area network will be discovered by Windows thanks to the UPnP function support of our

cameras.

www.acti.com

Firmware User’s Manual V6.04.15

6

In the example below, we successfully found D11 camera that we had just connected to the

network.

With the left mouse click on D11 it is possible to automatically launch the default browser of the

PC with the IP address of the target camera filled in the address bar of the browser already.

If you work with our cameras regularly, then there is even a better way to discover the

cameras in the network – by using IP Utility. The IP Utility is a light software tool that can not

only discover the cameras, but also list lots of valuable information, such as IP and MAC

addresses, serial numbers, firmware versions, etc, and allows quick configuration of multiple

devices at the same time.

The IP Utility can be downloaded for free from http://www.acti.com/IP_Utility

With just 1 click, you can launch the IP Utility and there will be an instant report as follows:

You can quickly notice the D11 model in the list. Click on the IP address to automatically launch

the default browser of the PC with the IP address of the target camera filled in the address bar of

the browser already.

www.acti.com

Firmware User’s Manual V6.04.15

7

Use the default IP address of a camera:

If there is no DHCP server in the given network, the user may have to assign the IP addresses to

both PC and camera manually to make sure they are in the same network segment.

When the camera is plugged into network and it does not detect any DHCP services, it will

automatically assign itself a default IP:

192.168.0.100

Whereas the default port number would be 80. In order to access that camera, the IP address of

the PC has to be configured to match the network segment of the camera.

Manually adjust the IP address of the PC:

In the following example, based on Windows 7, we will configure the IP address to 192.168.0.99

and set Subnet Mask to 255.255.255.0 by using the steps below:

1

2

3

4

www.acti.com

Firmware User’s Manual V6.04.15

8

Manually adjust the IP addresses of multiple cameras:

If there are more than 1 camera to be used in the same local area network and there is no DHCP

server to assign unique IP addresses to each of them, all of the cameras would then have the

initial IP address of 192.168.0.100, which is not a proper situation for network devices – all the IP

addresses have to be different from each other. The easiest way to assign cameras the IP

addresses is by using IP Utility:

With the procedure shown above, all the cameras will have unique IP addresses, starting from

192.168.0.101. In case there are 20 cameras selected, the last one of the cameras would have

the IP 192.168.0.120.

Later, by pressing the “Refresh” button of the IP Utility, you will be able to see the list of cameras

with their new IP addresses.

Please note that it is also possible to change the IP addresses manually by using the Web

browser. In such case, please plug in only one camera at a time, and change its IP address by

using the Web browser before plugging in the next one. This way, the Web browser will not be

confused about two devices having the same IP address at the same time.

www.acti.com

Firmware User’s Manual V6.04.15

9

Access the Camera

Now that the camera and the PC are both having their unique IP addresses and are under the

same network segment, it is possible to use the Web browser of the PC to access the camera.

You can use any of the browsers to access the camera, however, the full functionality is

provided only for Microsoft Internet Explorer.

The browser functionality comparison:

Functionality

Internet Explorer

Other browsers

Live Video

Yes

Yes*

Live Video Area Resizable

Yes

No

PTZ Control

Yes

Capture the snapshot

Yes

Video overlay based configuration (Motion

Detection regions, Privacy Mask regions)

Yes

No

All the other configurations

Yes

* The basic VLC media player (http://www.videolan.org) has to be installed in PC first before

using any non-Internet Explorer browsers to be able to get live video feed from the camera with

those browsers. It is a free and open source cross-platform multimedia player.

Disclaimer Notice: The camera manufacturer does not guarantee the compatibility of its cameras

with VLC player – since it is a third party software, the third party has the right to modify their

utility any time which might affect the compatibility. In such cases, please use Internet Explorer

browser instead.

When using Internet Explorer browser, the ActiveX control for video stream management will be

downloaded from the camera directly – the user just has to accept the use of such control when

prompted so. No other third party utilities are required to be installed in such case.

The following examples in this manual are based on Internet Explorer browser in order to

cover all functions of the camera.

www.acti.com

Firmware User’s Manual V6.04.15

10

Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web

browser and typing the following address into Web browser’s address bar:

http://192.168.0.100

Upon successful connection to the camera, the user interface called Web Configurator would

appear together with the login page. The HTTP port number was not added behind the IP

address since the default HTTP port of the camera is 80, which can be omitted from the address

for convenience.

Before logging in, you need to know the factory default Account and Password of the camera.

Account: Admin

Password: 123456

www.acti.com

Firmware User’s Manual V6.04.15

11

Live View

This section describes how to configure the IP camera. The administrator has unlimited access to

all settings, while the normal user can only view live video.

Login

Initially there exists only administrator’s account in

the camera (Account: Admin, Password:

123456) – you have to use that account to log in.

You can later create normal user accounts with

limited access rights if necessary.

Feel free to choose your local language from the list

of languages or keep it as English. After pressing

“Login”, you will be able to access the user interface

of Web Configurator.

Upon successful login, you will be able to see the Live View page. In case of

Internet Explorer browser, you may be prompted to allow the installation of

ActiveX control from the camera. Press “Install” then. The live video will

appear shortly after that.

www.acti.com

Firmware User’s Manual V6.04.15

12

Live View

The live view will appear automatically with the video resolution of 1280x720 (1MP cameras) or

1920x1080 (2-5MP cameras).

While being on the Live View page, the Live View icon appears as being pressed:

If you leave the Live View page, you can later return by pressing that button.

If the resolution of the PC’s monitor is bigger than the resolution of the live video, you will be able

to see the whole size of the video immediately. If not, you will only see part of the video at first

and you would have to use the scroll bars to see the rest of the video area. In order to see the

whole video on your display, you can temporarily re-scale the video to better fit your screen by

pressing the digital zoom buttons:

- Enlarge the video size digitally

- Reduce the video size digitally

Notice: These digital zoom adjustments do not influence the actual video resolution of the camera.

Regardless of how large or small the video appears on the display after pressing the digital zoom

buttons, the actual video stream size of the camera is the same as before.

www.acti.com

Firmware User’s Manual V6.04.15

13

You can also digitally re-scale the video to fully match the size of your display with just 1 click:

- Full screen Mode

You may use ESC key from the keyboard to exit the full screen mode.

The cameras have the dual stream capability – the Stream 1 is usually the high resolution

stream with the purpose of being recorded by NVR while Stream 2 has lighter video configuration

for NVR live view purposes, to reduce the computing power of the NVR PC. Both streams can be

configured under Web Configurator’s Setup page. To see how each of the stream looks like, there

are quick buttons on the Live View page:

- Show the Stream 1 video

- Show the Stream 2 video

When pressing the Stream 2 button, the Live View would look like this:

To capture the snapshots of the current live view, press the snapshot button. The snapshots are

saved in Pictures folder.

- Take a Snapshot

www.acti.com

Firmware User’s Manual V6.04.15

14

The cameras with audio function shall have the audio controls on Live View page.

To adjust the volume level of the speakers connected to the PC that runs the Web Configurator in

order to hear the audio from the camera’s microphone or line-in device, use the audio controls as

below:

Audio Muted:

Audio level adjusted to the maximum:

This volume control appears in user interface only when the Audio-in function of the camera has

been “Enabled” under Setup page.

For Fisheye cameras, the Miniature Fisheye-View and View Mode buttons appear on the Live

View screen.

By default, a miniature of the Fisheye view is shown on the lower right corner of the Live View,

press to hide the miniature fisheye-view or to display it.

www.acti.com

Firmware User’s Manual V6.04.15

15

You can change the viewing mode into:

- ePTZ View Mode

- Panorama View Mode

- Fisheye View Mode

ePTZ View Mode

ePTZ mode works as an optical PTZ (pan-tilt-zoom) function. You can change the viewing

direction by moving the mouse over the Live View screen and clicking towards the direction you

wish to view. The mouse cursor is represented by a red “+” mark.

If Miniature Fisheye-view is enabled, the current direction and scope of view is shown on the

Miniature Fisheye-view window with the red marking.

Panorama View Mode

This mode allows you to view the camera in panorama view where details can be seen more

clearly. When the camera is installed on the ceiling, there will be two panorama views, one for the

upper hemisphere and another for the lower hemisphere.

www.acti.com

Firmware User’s Manual V6.04.15

16

If Miniature Fisheye-view is enabled, the current scope of view is shown on the Miniature

Fisheye-view window with the red marking.

Fisheye View Mode

This mode shows the camera view as though viewing from a fish’s eye with the whole viewing

angle in sight but details may be too small and not be seen clearly.

www.acti.com

Firmware User’s Manual V6.04.15

17

Setup

The following chapters guide you through the Setup functions of the camera.

Access the Setup Page

To configure any of the camera settings, go to the Setup menu by pressing the following button

on Live View page:

- Go to Setup

The left side of the Setup page contains the list of Setup items.

Notice: The exact content of the menu list varies for each camera,

depending on the actual capabilities of each camera. This manual,

however, is designed to explain all the possible functions.

Several items in the Setup page are divided into groups, such as Network, IP Settings, etc. You

can expand the groups to see the sub-items by pressing the [+] button.

The following chapters of this manual explain each Setup item separately. The chapters are listed

in the same order as the list of Setup menu items.

www.acti.com

Firmware User’s Manual V6.04.15

18

Host

The section “Host” allows the administrator to define the name of the

camera and preferred user interface language.

There are two kinds of names – Host Name and Camera Name.

Host Name is used to identify the camera by a DHCP server. In some networks with very strict

security policy, it is required that all the network devices should have their host name, and when

the devices attempt to access the network by requesting an IP address from a DHCP server, the

DHCP server would check if the host name is among the allowed devices. On this page, it is

possible to edit the Host Name. To actually include the Host Name in DHCP discovery packet

sent from a camera, please go to IP Settings and make sure the device is in Dynamic IP

Address mode and “Use host name” is checked.

Camera Name is used to identify the device by Video Management System or by Software

Tools. Usually, upon installation of the camera, the actual installation location is used as an

easy-to-remember Camera Name, such as “Front Gate” or “Elevator 1”. In many cases the VMS

is able to modify the Camera Name directly via its own user interface without needing to access

Web Configurator.

Language selection under Host has the same purpose as the one on the login page of Web

Configurator.

After changing any of the items above, press Apply to save the changes. The Reset button

undoes the changes that had just been made but not Applied yet.

www.acti.com

Firmware User’s Manual V6.04.15

19

Date & Time

Each video frame contains a time stamp. The accuracy of the time stamp is very important for

incident investigators. Therefore the clock of the camera has to be adjusted to most accurate time

possible.

The section Date & Time provides the options for adjusting the date

and time of the camera.

There are two ways to adjust the date and time – automatically by getting date and time

regularly from any of the NTP servers worldwide, or manually by selecting proper time zone,

date and time. The automatic way can be used only if the camera has an access to NTP servers.

If you are using an isolated Local Area Network without Internet access, you can only use Manual

date and time adjustment mode.

When choosing SNTP/NTP Server for automatic date and time updating, you can key in the IP

address of the NTP server and the time interval for automatic time synchronization. If you want to

key in the domain name of NTP server instead, please make sure the DNS server IP address has

been set under IP Settings; otherwise the camera will not be able to resolve the domain name of

the NTP server.

www.acti.com

Firmware User’s Manual V6.04.15

20

If all the cameras are getting the date and time from the same NTP Server, you can be most sure

that the video clips from different cameras can be well synchronized later for comparison

purposes.

To choose the most suitable NTP Server to synchronize date and time with, please refer to the

worldwide pool of NTP Servers: http://www.pool.ntp.org/en/

When choosing Set Manually mode, you can adjust the date and time by the select boxes.

Choose the appropriate Time Zone from the select box, too. If your location is not listed there,

then pick any of the listed zones which GMT is identical with your location.

For the countries with daylight saving policy, there is Day Light Saving function with two different

types:

Type 1 – define the starting or ending time of daylight saving period by the number of the week

in the month (First, Second, Third or Last week).

Type 2 – define the starting or ending time of daylight saving period by the exact date in the

month (1-31).

Whether to choose Type 1 or Type 2, please refer to the daylight saving policy of given country.

After changing any of the items above, press Apply to save the changes. The Reset button

undoes the changes that had just been made but not Applied yet.

Page is loading ...

ACTi E62 User manual

ACTi E62 User manual

Related papers

Other documents