2. Home
  3. Home security & automation
  4. Security camera accessories
  5. Zebra
  6. MP7000
MP7000

Zebra MP7000 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Zebra MP7000 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions
worldwide. All other trademarks are the property of their respective owners. © 2020 Zebra Technologies Corp. and/or
its affiliates. All rights reserved. | www.zebra.com
MN-003948-01EN Rev. A - May 2020
MP7000 Scanner Scale Color Camera
Installation Instructions
Color Camera Parts
Installing the Color Camera
1. Disconnect the MP7000 power supply and POS interface cable.
2. Remove the platter from the MP7000.
3. Air-blow the rear tower cover (to remove any dust build-up).
4. Detach rear tower cover by lifting the center of the cover with your thumb to disengage from the tower housing and remove.
5. Air-blow the inner tower housing.
6. Pull the left yellow plastic seal plug straight out to remove.
7. Disconnect the PCB cable connector from the illumination PCB. Gently pull the connector body. Do not pull the wires.
8. Remove the illumination PCB. Lift the PCB tab with a finger while tipping the top of the illumination PCB away from the housing.
9. Insert the new illumination PCB to the left side, bottom edge first. Lift the PCB tab with a finger and tilt the PCB back against the
housing until tab snaps.
10. Re-install the corresponding seal plug.
IMPORTANT The USB cable included in the kit is the longest length permitted for USB 3.0. Cable extensions are not permissible.
If used, the camera may not operate properly.
Illumination PCB (2)
USB Cable
Rear Tower Cover
Color Camera Cable
Camera With Adapter
(Portrait or Landscape)
Service Label
Camera Lens Cover
IMPORTANT Color camera installation must be performed in a clean environment to prevent dust or any foreign matter ingress
into the optical chamber.
Seal Plug
Illumination
PCB
Inner Tower Housing
PCB Cable Connector
PCB Cable Connector
Illumination
PCB
Snap/Camera Opening Plug
*Camera Connector
Seal Plug
*Camera Connector
*Note: Camera connectors are only
included on PCBs used with the color
camera.
NOTE: There is a left and right Illumination PCB. The placement of the PCB tab is the key for the correct fit for each illumination
PCB.
PCB Tab
2
11. Repeat Step 6 through Step 10 on the right side of the device.
12. Re-connect the PCB cable connector to the illumination PCB on both sides of the device.
13. Disengage the snap and remove camera opening plug.
14. Remove the clear plastic lens cover from the color camera and snap in camera housing into place.
15. The color camera cable has four connectors:
a. Connect the 3-pin connector on the longest branch to the User Interface PCB.
b. Connect one 3-pin connector to each illumination PCB.
c. Connect the 5-pin connector to the color camera.
16. Route the camera cable through guiding ribs 1, 2, and 3 and under the cable retainer tab.
17. Attach the USB cable and route it under the cable retainer tab, through guiding ribs 1 and 2 to the side of the device.
18. Install the new rear tower cover.
19. Attach the service label next to the manufacturing label under the platter.
20. Replace the platter.
3-Pin
Connector to
User
Interface PCB
3-Pin Connectors
5-pin Connector
into Camera
USB Connector
NOTE: The USB cable only connects correctly in one orientation. When connected upside down, the camera does not operate and
the cable interferes with the rear housing.
Portrait Camera
Landscape Camera
USB Cable
Cable Retainer
Tab
Cable Guiding Ribs (1, 2, 3)
USB Cable
Service Label Placement
Under Platter
/