Garden Oasis 10 ft SQUARE COMMERCIAL OFFSET UMBRELLA Owner's manual

Brand: Garden Oasis

Model: 10 ft SQUARE COMMERCIAL OFFSET UMBRELLA

Type: Owner's manual

This manual is also suitable for

D71 M83931

02620606-0

805670024314

Product Code: D71 M83931

10 ft SQUARE COMMERCIAL

OFFSET UMBRELLA

(DOUBLE PLASTIC BASE)

SEARS INSISTS ON THE HIGHEST STANDARDS OF

FURNITURE. EACH PIECE HAS BEEN CAREFULLY

INSPECTED BEFORE SHIPMENT.

IN CASE OF PROBLEM, DO NOT RETURN TO THE

STORE, CALL YOTRIO CORPORATION AT PHONE#

1-866-905-4107 BETWEEN THE HOURS OF

8:30 AM TO 5:00 PM PST, MONDAY THROUGH

FRIDAY, FOR ANY QUESTIONS OR PROBLEM YOU

MAY HAVE.

IMPORTANT

10x10′ Square Offset Umbrella Assembly Instruction

PARTS LIST

PARTS

NO.

QTY DESCRIPTION NAME

A 1 PC

1 PCB

C 1 PC

8 PCS

1 PC

G 1 PC

H 2 PCS

1 PC

2 PCS

4 PCS

1 PC

Lower Bracket

Upper Bracket

Base Tube

M10x24mm Bolts

Flat Washer

360° Revolve Device

Footplate

M6x10mm Bolts

M6x20mm Bolts

Plastic Base

Plastic Base Cover

Plastic Base Top Cover 2

Plastic Base Top Cover 1

Sunshade

PARTS LIST

PARTS

NO.

QTY DESCRIPTION NAME

1 PC

S8 Wrench

S5 Wrench

Crank

Steel Stick

PE Umbrella Cover

10x10′ Square Offset Umbrella Assembly Instruction

Connecting Link

Step 01:

Place Upper Bracket (B) onto Lower Bracket (A) as shown.

Step 02:

Loosen the screw (I) counterclockwise by using S5 Wrench (P), then take out

Base Tube (C) from Sunshade (N).

Step 03:

(2) Line up the bolt holes on the 360° Revolve Device (F) with the corresponding

bolt holes on the two brackets. Then screw the M10x24 Bolts (D) on with Flat

Washer (E) by using S8 Wrench (O). Then screw Base Tube (C) on the 360°

Revolve Device (F) by using the same method.

10x10′ Square Offset Umbrella Assembly Instruction

(1) Insert the Connecting Link (T) into 360° Revolve Device (F), then screw the

M6x10 Bolts (H) by using S5 Wrench (P).

Step 05:

Fill entire base with dry sand and make level to the top of the triangular sections.

Add water to the sand for additional weight. A minimum of 125 lbs. of sand is

required for the first level.

Step 06:

Repeat the procedure of step 4 to install the remaining plastic base (M).

10x10′ Square Offset Umbrella Assembly Instruction

Step 04:

Install the Plastic Base (M) on the brackets. Embed the chocks of the left part

(M) into the rabbets of the right part (M).

Step 08:

Cover the Plastic Base (M) with the Plastic Covers (L).

Step 09:

Put the Plastic Base Top Cover 2 (K) onto the Plastic Base Cover (L), then put the

Plastic Base Top Cover 1 (J) onto the Plastic Base Top Cover 2 (K).

10x10′ Square Offset Umbrella Assembly Instruction

Step 07:

Fill entire base with dry sand and make level to the top of the triangular sections.

Add water to the sand for additional weight. A minimum of 125 lbs. of sand is

required for the second level. You should now have a required minimum of 250

lbs of dry sand in your plastic base (M).

Step 11:

Insert the Sunshade (N) into the Base Tube and fix it by M6*20 Bolts (I).

Step 12:

Open the umbrella canopy by hand.

10x10′ Square Offset Umbrella Assembly Instruction

Step 10:

Insert the Footplate (G) into the 360 Degrees Revolve Device, and fix it by M6*10mm

Bolts (H).

Step 14:

Unfold the umbrella canopy, rotate the Crank (S) clockwise, the umbrella can be unfold

gradually.

Step 15:

The handrails can be upward or downward by press the handrails button, adjust the

canopy to the needing gradient, release hand to fix the umbrella canopy.

10x10′ Square Offset Umbrella Assembly Instruction

Step 13:

Press the button can upward, release the button can fix the umbrella canopy.

Step 17:

Rotate the Crank (S) anti-clockwise by right hand, close the canopy gradually, then

hold the handrails by left hand and press the button to downward, close the canopy

completely, release hand to fix the umbrella.

10x10′ Square Offset Umbrella Assembly Instruction

Step 16:

The umbrella is able to turn up to 360 degrees by stepping the Footplate (G).

Step 18:

Tightening the two Steel Stick (Q) clockwise.

Step 19:

Steel Stick to support hoop, packing the umbrella from up to down using PE

Umbrella Cover (R).

Step 20:

Pulling the rope downward, close the zipper of the Umbrella Cover.

10x10′ Square Offset Umbrella Assembly Instruction

See our extensive assortment of outdoor living products on-line at www.sears.com and www. kmart.com.

Garden Oasis 10 ft SQUARE COMMERCIAL OFFSET UMBRELLA Owner's manual

Brand: Garden Oasis

Model: 10 ft SQUARE COMMERCIAL OFFSET UMBRELLA

Type: Owner's manual

This manual is also suitable for

D71 M83931

Download PDF

report

Garden Oasis 10 ft SQUARE COMMERCIAL OFFSET UMBRELLA Owner's manual

This manual is also suitable for

Garden Oasis 10 ft SQUARE COMMERCIAL OFFSET UMBRELLA Owner's manual

Related papers

Other documents