Garden Oasis 10 ft SQUARE COMMERCIAL OFFSET UMBRELLA Owner's manual

Garden Oasis
Brand
Garden Oasis
Model
10 ft SQUARE COMMERCIAL OFFSET UMBRELLA
Type
Owner's manual

This manual is also suitable for

02620606-0
805670024314
Product Code: D71 M83931
10 ft SQUARE COMMERCIAL
OFFSET UMBRELLA
(DOUBLE PLASTIC BASE)
SEARS INSISTS ON THE HIGHEST STANDARDS OF
FURNITURE. EACH PIECE HAS BEEN CAREFULLY
INSPECTED BEFORE SHIPMENT.
IN CASE OF PROBLEM, DO NOT RETURN TO THE
STORE, CALL YOTRIO CORPORATION AT PHONE#
1-866-905-4107 BETWEEN THE HOURS OF
8:30 AM TO 5:00 PM PST, MONDAY THROUGH
FRIDAY, FOR ANY QUESTIONS OR PROBLEM YOU
MAY HAVE.
IMPORTANT
1
10x10′ Square Offset Umbrella Assembly Instruction
PARTS LIST
PARTS
NO.
QTY DESCRIPTION NAME
A 1 PC
1 PCB
C 1 PC
D
8 PCS
E
8 PCS
F
1 PC
G 1 PC
H 2 PCS
I
1 PC
J
1 PC
K
L
M
N
1 PC
2 PCS
4 PCS
1 PC
Lower Bracket
Upper Bracket
Base Tube
M10x24mm Bolts
Flat Washer
360° Revolve Device
Footplate
M6x10mm Bolts
M6x20mm Bolts
Plastic Base
Plastic Base Cover
Plastic Base Top Cover 2
Plastic Base Top Cover 1
Sunshade
1
PARTS LIST
PARTS
NO.
QTY DESCRIPTION NAME
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
O
P
Q
R
S
T
S8 Wrench
S5 Wrench
Crank
Steel Stick
PE Umbrella Cover
2
10x10′ Square Offset Umbrella Assembly Instruction
Connecting Link
Step 01:
Place Upper Bracket (B) onto Lower Bracket (A) as shown.
Step 02:
Loosen the screw (I) counterclockwise by using S5 Wrench (P), then take out
Base Tube (C) from Sunshade (N).
Step 03:
(2) Line up the bolt holes on the 360° Revolve Device (F) with the corresponding
bolt holes on the two brackets. Then screw the M10x24 Bolts (D) on with Flat
Washer (E) by using S8 Wrench (O). Then screw Base Tube (C) on the 360°
Revolve Device (F) by using the same method.
3
10x10′ Square Offset Umbrella Assembly Instruction
(1) Insert the Connecting Link (T) into 360° Revolve Device (F), then screw the
M6x10 Bolts (H) by using S5 Wrench (P).
Step 05:
Fill entire base with dry sand and make level to the top of the triangular sections.
Add water to the sand for additional weight. A minimum of 125 lbs. of sand is
required for the first level.
Step 06:
Repeat the procedure of step 4 to install the remaining plastic base (M).
4
10x10′ Square Offset Umbrella Assembly Instruction
Step 04:
Install the Plastic Base (M) on the brackets. Embed the chocks of the left part
(M) into the rabbets of the right part (M).
Step 08:
Cover the Plastic Base (M) with the Plastic Covers (L).
Step 09:
Put the Plastic Base Top Cover 2 (K) onto the Plastic Base Cover (L), then put the
Plastic Base Top Cover 1 (J) onto the Plastic Base Top Cover 2 (K).
5
10x10′ Square Offset Umbrella Assembly Instruction
Step 07:
Fill entire base with dry sand and make level to the top of the triangular sections.
Add water to the sand for additional weight. A minimum of 125 lbs. of sand is
required for the second level. You should now have a required minimum of 250
lbs of dry sand in your plastic base (M).
Step 11:
Insert the Sunshade (N) into the Base Tube and fix it by M6*20 Bolts (I).
Step 12:
Open the umbrella canopy by hand.
6
10x10′ Square Offset Umbrella Assembly Instruction
Step 10:
Insert the Footplate (G) into the 360 Degrees Revolve Device, and fix it by M6*10mm
Bolts (H).
Step 14:
Unfold the umbrella canopy, rotate the Crank (S) clockwise, the umbrella can be unfold
gradually.
Step 15:
The handrails can be upward or downward by press the handrails button, adjust the
canopy to the needing gradient, release hand to fix the umbrella canopy.
7
10x10′ Square Offset Umbrella Assembly Instruction
Step 13:
Press the button can upward, release the button can fix the umbrella canopy.
Step 17:
Rotate the Crank (S) anti-clockwise by right hand, close the canopy gradually, then
hold the handrails by left hand and press the button to downward, close the canopy
completely, release hand to fix the umbrella.
8
10x10′ Square Offset Umbrella Assembly Instruction
Step 16:
The umbrella is able to turn up to 360 degrees by stepping the Footplate (G).
Step 18:
Tightening the two Steel Stick (Q) clockwise.
Step 19:
Steel Stick to support hoop, packing the umbrella from up to down using PE
Umbrella Cover (R).
Step 20:
Pulling the rope downward, close the zipper of the Umbrella Cover.
9
10x10′ Square Offset Umbrella Assembly Instruction
See our extensive assortment of outdoor living products on-line at www.sears.com and www. kmart.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Garden Oasis 10 ft SQUARE COMMERCIAL OFFSET UMBRELLA Owner's manual

Garden Oasis
Brand
Garden Oasis
Model
10 ft SQUARE COMMERCIAL OFFSET UMBRELLA
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents