Airmax PS10 Installation guide

Category
Car kits
Type
Installation guide
INSTALLATION INSTRUCTIONS
REPLACEMENT PARTS:
DESCRIPTION PART #
1/2" Cam-lock - Female End 490287
1/2" Cam-lock - Male End 490288
Insert Reducer 3/8" - 1/2" 490118
Male Adapter 1/2" 490144
Stainless Hose Clamp 1" 490158
PRODUCT WARRANTY:
All Deep Water Conversion Kits carry a 1-year warranty. Airmax® will repair
or replace any kits found to be defective. This limited warranty is extended
exclusively to the original purchaser and begins from the date of original
shipment. Abuse, misuse or alterations of this product will void all warranty.
Please contact your local dealer to obtain a Return Merchandise Authorization
(RMA) Number prior to returning any product. Failure to request an RMA number
may result in delay or dismissal of your warranty claim.
THANK YOU FOR CHOOSING:
Airmax
®
, Inc.
Safe, Simple Solutions
P.O. Box 38
Romeo, MI 48065
866-424-7629
www.airmaxeco.com
PS10 Deep Water Conversion Kit
(Item #510435)
PS20 Deep Water Conversion Kit
(Item #510436)
PS30 Deep Water Conversion Kit
(Item #510437)
PS40 Deep Water Conversion Kit
(Item #510438)
PS80 Deep Water Conversion Kit
(Item #510439)
airmaxeco.com | 866-424-7629 | P.O.Box 38 | Romeo, MI 48065
Deep Water
Conversion Kit
4
Important Information................... 2
Getting to Know Your Deep Water Kit ....... 2
Installing Your Deep Water Kit .............3
Replacement Parts.......................4
Product Warranty ........................ 4
Table of Contents:
For use with PondSeries
Aeration Systems in Ponds Deeper Than 21’ Deep.
PS10 PS20 PS30 PS40 PS80
A
1/2” Cam-lock - Female End
w/ Insert Reducer
1 2 3 4 8
B
1/2” Cam-lock - Male End
w/ Male Adapter
1 2 3 4 8
C
Stainless Hose Clamp(s)
2 4 6 8 16
B
A
C
IMPORTANT INFORMATION:
Please read these instructions thoroughly before use. Failure to follow instructions may
result in equipment damage or failure, losses, injury or death.
WARNING:
To reduce the risk of electric shock or injury:
ALWAYS unplug the compressor from the power source and release pressure from
the airlines before installing, removing or servicing the Deep Water Conversion Kit
components.
IMPORTANT: Airmax® is not responsible for equipment damage or failure, losses,
injury or death resulting from failure to follow safety precautions, misuse or
abuse of equipment.
INSTALLING YOUR
DEEP WATER CONVERSION KIT:
GETTING TO KNOW
YOUR DEEP WATER CONVERSION KIT:
1
Remove Quick Disconnect End
from Manifold Flex Tube
Cut approximately 1” of airline from the end of each Flex
Tube using a tube cutter or utility knife. This will remove
the quick disconnect end. The quick disconnect end may be
discarded. Repeat for each ex tube.
Tools Required:
Tube Cutter or Utility Knife
⁄” Nut Driver or
Flathead Screwdriver
2
Install Female End of Cam-lock
Slide a hose clamp onto the ex tube, then insert the insert
reducer from the female end of the Cam-lock into the ex
tube. Using a nut driver or athead screwdriver, tighten the
hose clamp onto the insert reducer.
3
Install Male End of Cam-lock
Slide a hose clamp onto the diuser airline, then insert
the male adapter from the male end of the Cam-lock
into the diuser airline. Tighten the hose clamp onto the
male adapter.
4
Join Cam-lock Ends
Open the locks on the female end of the Cam-lock by
pushing on the button and pulling the lock outward.
Then insert the male Cam-lock end rmly into the female
Cam-lock end. Lock the ends together by pushing both locks
down until they click.
5
Repeat Process
Repeat this process for each Cam-lock set to be installed.
airmaxeco.com | 866-424-7629 P.O.Box 38 | Romeo, MI 48065
2 3
  • Page 1 1
  • Page 2 2

Airmax PS10 Installation guide

Category
Car kits
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI