AudioControl ACR-1 User manual

AudioControl
Brand
AudioControl
Model
ACR-1
Type
User manual

AudioControl ACR-1 is a remote level control designed to work with specific AudioControl line output converters and processors. It can be surface or custom-mounted to add level control or total system volume control to your audio system. Installation is simple and no power is required. The ACR-1 may be mounted under a dash or console using its own bracket or through custom mounting holes in the dash/console. For a custom, finished look, the ACR-1 can be flush mounted directly on the dash/console panel. The ACR-1 comes with a 20' phone cable (RJ-11).

AudioControl ACR-1 is a remote level control designed to work with specific AudioControl line output converters and processors. It can be surface or custom-mounted to add level control or total system volume control to your audio system. Installation is simple and no power is required. The ACR-1 may be mounted under a dash or console using its own bracket or through custom mounting holes in the dash/console. For a custom, finished look, the ACR-1 can be flush mounted directly on the dash/console panel. The ACR-1 comes with a 20' phone cable (RJ-11).

“Maximum Processing with Minimal Effort”
AudioControl’s new Matrix DSP processors
When you require total control and optimization to achieve great sound quality, AudioControl Dig-
ital Signal Processors are the solution. The powerful DM-810 and DM-608 DSP processors allow
users to truly optimize the performance of their audio system, regardless of whether they are using
a factory or aftermarket source, and to truly achieve our goal “Making Good Sound Great”. These
highly versatile Digital Signal processors are equipped with key features, such as active speaker-lev-
el inputs, line-level and digital audio inputs, providing up to 10 channels of output. AudioControl’s
“smart user” interface contains the power of AudioControl processing through a flexible PC inter-
face packed full of features and simply laid out. Includes signal summing, 30 bands of equalization,
signal time-alignment, input delay and phase correction, plus AudioControl proprietary features
like AccuBASS®, GTO™ Signal Sense, and MILC™ as well as integrated input and output RTA’s.
UPGRADE ACCESSORY
PRECISE AND TACTILE REMOTE LEVEL CONTROL
REMOTE CAN BE FLUSH-MOUNTED FOR CUSTOM INSTALLATIONS
REMOTE LEVEL CONTROL
Add volume control to any system
The ACR-1 is a remote level control designed to work with specific AudioControl line output converters and processors. The ACR-1
can be surface or custom-mounted to add level control or total system volume control, and more to your audio system. Installation is
simple and no power is required.
Scan for
Compatible
Products
REMOTE LEVEL CONTROL
855814 00534 1
22410 70th Ave West, Mountlake Terrace, WA 98043 USA
Phone 425-775-8461
www.audiocontrol.com ©2022 AudioControl. All rights reserved. P/N 912-078-0 Rev B
Placement And Mounting of the ACR-1
The ACR-1 may be mounted under a dash or console using its own
bracket or through custom mounting holes in the dash/console. It
should be within reach of the driver and in a spot where the LED is
plainly visible.
Bracket Installation
ACR-1 mounts with four screws, which attach to the underside of
a dashboard/console. Slide under the dash or console and place
the ACR-1 in its mounting position, mark the mounting holes,
drill pilot holes, and secure with screws.
Custom Installation
For that custom, finished look, the ACR-1 can be flush
mounted directly on the dash/console panel (or anywhere
else). Referencing the drawing right, disassemble the ACR-1.
Drill a 9/32” (7 mm) hole in the panel for the control along with
a 3/32” (2.3 mm) hole for the lock tab and a 1/8” (3 mm) hole for
the LED. Reassemble the ACR-1 components on the dashboard or
console.
What’s Included?
ACR-1 Remote Level Control, 20’ Phone Cable (RJ-11)
  • Page 1 1
  • Page 2 2

AudioControl ACR-1 User manual

AudioControl
Brand
AudioControl
Model
ACR-1
Type
User manual

AudioControl ACR-1 is a remote level control designed to work with specific AudioControl line output converters and processors. It can be surface or custom-mounted to add level control or total system volume control to your audio system. Installation is simple and no power is required. The ACR-1 may be mounted under a dash or console using its own bracket or through custom mounting holes in the dash/console. For a custom, finished look, the ACR-1 can be flush mounted directly on the dash/console panel. The ACR-1 comes with a 20' phone cable (RJ-11).

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents