Crux VIMCF-93C Owner's manual

Brand: Crux

Model: VIMCF-93C

Category: Cars

Type: Owner's manual

Crux VIMCF-93C is a video in-motion interface specifically designed for Dodge, Jeep, and Ram vehicles manufactured between 2013 and 2015. It allows passengers to access and input navigation addresses while the vehicle is in motion, enhancing convenience and safety.

8-PIN

(male plug)

4 5 6

1 2 3

TO FACTORY

HARNESS

VOLUME TUNE

52-PIN

(male plug)

TO FACTORY

DISPLAY

52-PIN

(female plug)

4 5 6

TO ENABLE VIDEO

IN-MOTION 1. On = Enable VIM

2. Not Used

3. Not Used

4. Not Used

5. Not Used

6. Not Used

1 2 3

SAFETY WARNING:

THIS INTERFACE IS DESIGNED TO ACTIVATE

VIDEO IN-MOTION TO ALLOW THE PASSENER

ACCESS TO THE ADDRESS INPUT WHILE THE

VEHICLE IS IN-MOTION. THIS INTERFACE MAY

CAUSE AN ERROR WHEN SERVICED AT THE OEM

DEALER. BE AWARE THAT MOST DEALERS

WILL ATTEMPT TO VOID THE MANUFACTURERS

WARANTY WHEN INSTALLING ANY AFTERMARKET

EQUIPMENT. IMPROPER USE OF THIS INTERFACE

BY THE DRIVER MAY RESULT IN CITATION. DRIVER

MUST KEEP FULL ATTENTION ON THE ROAD AND

RESPOSIBILITY ON THE SAFETY OF HIS

PASSENGERS.

INTERFACING SOLUTIONS

VIDEO IN-MOTION FOR DODGE, JEEP & RAM VEHICLES 2013-UP

DODGE

2014 - 2015 Durango

RAM

2013 - 2015 1500

2013 - 2015 2500

2013 - 2015 3500

JEEP

2014 - 2015 Grand Cherokee

IMPORTANT:

Compatible Nav Radio Type:

U-CONNECT 8.4” SCREEN (1-Piece)

VIMCF-93C We recommend reading this installation guide rst before starting any

work. Following these instructions from “Start” to” Finish” will ensure

a smooth and hassle free installation. We oer telephone support M-F

9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.

PARTS INCLUDED:

(1) CF-93C Interface

(1) CF-93C T-Harness

(1) Instruction

PRECAUTIONS:

- Remove the negative side of the battery to avoid any short circuits

durring the installation.

- Do not install the interface near any major components or near the

HVAC system. This may cause damage or overheating to the vehicle.

- Do not disconnect the airbag connection behind the radio panel.

PRELIMINARY:

Please read the entire mannual before installing this interface.

INSTALLATION OVERVIEW

TROUBLE SHOOTING

1. No video display while driving.

- Make sure the dip swithces are in the proper location.

Rev. 012015

INSTALLING THE INTERFACE:

1. Remove the factory display to gain access to the factory connectors.

2. Remove the 52-Pin connector from behind the display.

2. Make the T-Harness connections behind the factory display.

(if the connectors do not match please contact tech support)

4. Set dip switch “1” to permanently activate the VIM feature.

5. Test the Navigation address input while the car is in-motion to verify

the VIM is active.

SETTING THE DIP SWITCHES

8-PIN

(male plug)

4 5 6

1 2 3

TO FACTORY

HARNESS

VOLUME TUNE

52-PIN

(male plug)

TO FACTORY

DISPLAY

52-PIN

(female plug)

4 5 6

TO ENABLE VIDEO

IN-MOTION 1. On = Enable VIM

2. Not Used

3. Not Used

4. Not Used

5. Not Used

6. Not Used

1 2 3

8.4”

DISPLAYS

INTERFACING SOLUTIONS

VIDEO IN-MOTION FOR DODGE, JEEP & RAM VEHICLES 2013-UP

DODGE

2014 - 2015 Durango

RAM

2013 - 2015 1500

2013 - 2015 2500

2013 - 2015 3500

JEEP

2014 - 2015 Grand Cherokee

IMPORTANT:

Compatible Nav Radio Type:

U-CONNECT 8.4” SCREEN (1-Piece)

VIMCF-93C

Rev. 012015

COMPATIBLE RADIOS:

8.4” SCREEN

(SEPARATE KNOBS)

One Piece Radio

5” SCREEN

6-BUTTON

(SEPARATE

KNOBS)

4.3” SCREEN

6-BUTTON

(2 KNOBS)

4.3” SCREEN

4-BUTTON

(2 KNOBS)

Crux VIMCF-93C Owner's manual

Brand: Crux

Model: VIMCF-93C

Category: Cars

Type: Owner's manual

Download PDF

report

Crux VIMCF-93C Owner's manual

Crux VIMCF-93C Owner's manual

Related papers

Other documents