Revision: 1.0
1
Revision Description Date
1.0 Release 2010/01/11
AR-N8601FL
System Guide
Revision: 1.0
2
Contents
AR-N8601FL System Guide
1 Introduction......................................................................................... 4
1.1 Specifications.................................................................................................4
1.2 Packing List....................................................................................................5
1.3 System Dissection.........................................................................................5
2 Procedures of Assembly/Disassembly............................................. 8
2.1 Installing the CF card........................................................................ 8
AR-B8601 Board Guide
1 Introduction........................................................................................11
1.1 Package Contents........................................................................................11
1.2 Block Diagram..............................................................................................12
2 H/W Information................................................................................ 13
2.1 Locations (Top side)....................................................................................13
2.2 Connectors and Jumpers Location............................................................14
2.3 Jumpers and Connectors Pin define..........................................................15
3 WATCHDOG, GPIO PROGRAMMING............................................... 17
4 BIOS Setting...................................................................................... 24
4.1 Main Setup....................................................................................................25
4.2 Advanced Chipset Setup.............................................................................27
4.3 Power Setup .................................................................................................29
4.4 PnP/PCI Setup..............................................................................................30
4.5 Peripherals Setup.........................................................................................32
4.6 PC Health Setup...........................................................................................34
Revision: 1.0
3
4.7 Boot Setup....................................................................................................35
4.8 Exit Setup .....................................................................................................36
Revision: 1.0
4
AR-N8601FL System Guide
1 Introduction
Acrosser Microbox Networking device AR-N8601FL, It is a small, cost-effective,
Fanless and entry-level UTM (Unified Threat Management) hardware, which is
suitable for small office. Base on VIA CN700 with ULV Eden 500MHz CPU, the
AR-N8601FL general very low heat to follow the low power consumption trend.
With Fanless design, the AR-N8601FL can keep longer lifetime. This is an important
feature for 24 hours networking device.
By three 10/100 RJ-45 LAN’s, the AR-N8601FL is sufficient for the small
business security hardware solution.
Key features:
VIA EDEN ULV 500 CPU.
VIA CN700+8237R plus Chipsets.
DDRII memory support (533MHz).
3 x 10/100LAN RTL8100C.
CF socket, 1x SATA, SATA power, and 2 x USB.
Console, VGA (pinhead), KB/MS (Pinhead).
Support PXE boot from LAN.
Compact size.
1.1 Specifications
System : AR-N8601FL
CPU Board : AR-B8601
Dimensions : 210*150*33(mm)
Revision: 1.0
5
1.2 Packing List
Description Quantity
AR-N8601FL 1
Console cable 1
VGA cable 1
Software driver CD 1
Quick user’s manual 1
Power adaptor 1
Power cord 1
1.3 System Dissection
(1) Dimensions
Revision: 1.0
6
(2) Front Panel
Back Panel
Led (Power & HDD)
LAN1~3 COM PORT POWER JACK
LAN led (Link & ACT)
USB*2
Revision: 1.0
7
(3) System Configuration
Item Description Quantity
1 TOP COVER 1
2 BOTTOM BASE 1
3 CF SOCKET 1
4 RAM SOCKET 1
5 FOOT PAD 4
1
3 5
2
4
Revision: 1.0
8
2 Procedures of Assembly/Disassembly
2.1 Installing the CF card.
Follow this guide to install CF card step-by-step.
1. Unfasten four screws of chassis top cover and open it.
(a) Unscrew left side screws of chassis top cover
(b) Unscrew right side screws of chassis top cover
Unscrew
Unscrew
Unscrew
Unscrew
Revision: 1.0
9
(c) Open chassis top cover
2. Insert CF card into the CF socket.
Revision: 1.0
10
3. Finally, follow step1 to assemble the top cover and fasten it with four screws.
Revision: 1.0
11
AR-B8601 Board Guide
1 Introduction
Acrosser Microbox Networking device AR-N8601 is a small, cost-effetive and
entry-level UTM (Unified Threat Management) hard ware, which is suitable for small
office. Base on VIA CN700 with ULV Eden 500MHz CPU, the AR-N8601 general
very low heat. We also put a quiet Fan to keep the low noise which will not cause
uncomfortable voice. By three 10/100 Lans, the AR-N8601 is sufficient for the small
business security hardware solution
1.1 Package Contents
Check if the following items are included in the package:
Quick Manual.
AR-B8601.
1 x Software Utility CD.
Revision: 1.0
12
1.2 Block Diagram
Revision: 1.0
13
2 H/W Information
This chapter describes the installation of AR-B8601. First, it shows the function
diagram and the layout of AR-B8601. It then describes the unpacking information,
as well as the jumpers and connectors setting for the AR-B8601 configuration.
2.1 Locations (Top side)
Revision: 1.0
14
2.2 Connectors and Jumpers Location
2.2.1 Locations (Top side)
LED1: POWER,HDD LED Ethernet RJ-45 (LAN1)
LED2, LED3, LED4: LAN LED
Ethernet RJ-45 (LAN2)
USB Connector1 Ethernet RJ-45 (LAN3)
USB Connector2 VGA Connector
DDR2 Memory Slot Serial Port
PCI Slot (3.3 Volt) Power Jack (12V Input)
JP1: CMOS Jumper Panel Connector
SATA Power Connector GPIO Connector
SATA Connector Compact Flash Connector
FAN Connector
Revision: 1.0
15
2.3 Jumpers and Connectors Pin define
1. LED1: POWER HDD LED 2. LED2,LED3,LED4:
LAN LED
3. USB Connector1
LDE1 Description
UP
POWER
DOWN
HDD
LED Description
UP
LINK
DOWN
ACTS
PIN SIGNAL PIN SIGNAL
1
+5V
2
+5V
3
USB2-
4
USB3-
5
USB2+
6
USB3+
7
GND
8
GND
9
GND
10
GND
4. USB Connector2 5. DDR2 Memory Slot 6. PCI Slot (3.3 Volt)
PIN SIGNAL PIN SIGNAL
1
+5V
2
+5V
3
USB0-
4
USB1-
5
USB0+
6
USB1+
7
GND
8
GND
9
GND
10
GND
SODIMM Memory
Slot
PCI Slot (3.3 Volt)
7. JP1: CMOS Jumper 8. SATA Power
Connector
9. SATA Connector
JP1 Description
1-2
NORMAL(default)
2-3
RESET COMS
SET SIGNAL
1
+12V
2
GND
3
+3.3V
4
+5V
PIN SIGNAL PIN SIGNAL
1
GND
2
TX+
3
TX-
4
GND
5
RX+
6
RX-
7
GND
Revision: 1.0
16
10. Keyboard / Mouse
Connector
11./12./13. Ethernet RJ-45
(LAN1/LAN2/LAN3)
14. VGA Connector
PIN Description
1
GND
2
FAN VCC
3
SENSE
PIN SIGNAL PIN SIGNAL
1
TX+
5
N/C
2
TX-
6
RX-
3
RX+
7
N/C
4
N/C
8
N/C
PIN Description
1
RED (R)
2
Ground
3
GREEN (G)
4
Ground
5
BLUE (B)
6
Ground
7
VERTICAL
SYNCHRON (VS)
8
CLOCK (CLK)
9
HORIZONTAL
SYNCHRON (HS)
10
DATA (SDATA)
15. Serial Port 16. Power Jack (12V Input) 17. Panel Connector
PIN Description
1
DATA CARRIER
DETECT (DCD)
2
RECEIVE DATA
(RXD)
3
TRANSMIT DATA
(TXD)
4
DATA TERMINAL
READY (DTR)
5
GROUND
6
DATA SET READY
(DSR)
7
REQUEST TO
SENTD (RTS)
8
CLEAR TO SEND
(CTS)
9
RING INDICATOR
(RI)
Power Jack (12V Input)
SET SIGNAL
1-2
POWER LED
3-4
RSET
5-6
POWER
BUTTOM
7-8
OPEN: ATX
MODE
CLOSE: AT
MODE
(default)
18. GPIO Connector 19. Compact Flash Connector
PIN SIGNAL PIN SIGNAL
1
VCC
2
GND
3
GPIO0
4
GPIO4
5
GPIO1
6
GPIO5
7
GPIO2
8
GPIO6
9
GPIO3
10
GPIO7
Compact Flash Connector
Revision: 1.0
17
3 WATCHDOG, GPIO PROGRAMMING
GPIO Sample Code
//===========================================================================
// Turbo C++ Version 3.0 Copyright(c) 1990, 1992 by Borland International,Inc.
//===========================================================================
// Describe : GPIO10~GPIO17 Test utility for W83697HF.
// Date : 06/26/2009
// Author : Willy
//===========================================================================
#include <conio.h>
#include <stdio.h>
void Show_Help();
void Show_Fail();
void Show_Pass();
//===========================================================================
// Main procedure
//===========================================================================
int main(int argc)
{
unsigned char IO_PORT_BASE=0x2E; // DATA_PORT = IO_PORT_BASE + 1;
unsigned char data;
int result=0;
if ( argc > 1 )
{ Show_Help(); return 1; }
clrscr();
textcolor(WHITE);
gotoxy(1, 1);
cprintf("<>==========================================================================<>");
gotoxy(1, 2); cprintf("|| W83697HF GPIO Test Utility v1.0 Acrosser Technology Co., Ltd. ||");
gotoxy(1, 3);
cprintf("<>==========================================================================<>");
gotoxy(1, 4);
cprintf("<>==========================================================================<>");
Revision: 1.0
18
gotoxy(1, 5); cprintf("|| Model Name : ||");
gotoxy(1, 6); cprintf("|| SIO IO Base : ||");
gotoxy(1, 7);
cprintf("<>==========================================================================<>");
// Show Got Parameter Informat
textcolor(LIGHTGRAY);
gotoxy(18,6); cprintf("%X",IO_PORT_BASE);
// Enter W83697HF Config
outportb(IO_PORT_BASE,0x87);
outportb(IO_PORT_BASE,0x87);
// Set Multi-function Pins to GPIO
outportb(IO_PORT_BASE,0x29);
outportb(IO_PORT_BASE+1,(inportb(IO_PORT_BASE+1) | 0x80));
// Select GPIO Port device
outportb(IO_PORT_BASE,0x07);
outportb(IO_PORT_BASE+1,0x07);
// Set GPIO Port Active
outportb(IO_PORT_BASE,0x30);
outportb(IO_PORT_BASE+1,0x01);
// Set W83697HF GPIO10~13 to Output, GPIO14~GPIO17 to Input
outportb(IO_PORT_BASE,0xF0);
outportb(IO_PORT_BASE+1,0xF0);
// Set W83697HF GPIO10~13 to High
outportb(IO_PORT_BASE,0xF1);
outportb(IO_PORT_BASE+1,0x0F);
// Read W83697HF GPIO14~17 Status, if not High error.
data=inportb(IO_PORT_BASE+1)&0xF0;
if(data!=0xF0)
result=1;
// Set W83697HF GPIO10~13 to Low
outportb(IO_PORT_BASE,0xF1);
Revision: 1.0
19
outportb(IO_PORT_BASE+1,0x00);
// Read W83697HF GPIO14~17 Status, if not Low error.
data=inportb(IO_PORT_BASE+1)&0xF0;
if(data!=0x00)
result=1;
// Set W83697HF GPIO10~13 to input, GPIO14~GPIO17 to Output
outportb(IO_PORT_BASE,0xF0);
outportb(IO_PORT_BASE+1,0x0F);
// Set W83697HF GPIO14~17 to High
outportb(IO_PORT_BASE,0xF1);
outportb(IO_PORT_BASE+1,0xF0);
// Read W83697HF GPIO10~13 Status, if not High error.
data=inportb(IO_PORT_BASE+1)&0x0F;
if(data!=0x0F)
result=1;
// Set W83697HF GPIO14~17 to Low
outportb(IO_PORT_BASE,0xF1);
outportb(IO_PORT_BASE+1,0x00);
// Read W83697HF GPIO14~17 Status, if not Low error.
data=inportb(IO_PORT_BASE+1)&0x0F;
if(data!=0x00)
result=1;
// Exit W83697HF Config
outportb(IO_PORT_BASE,0xAA);
if(result)
Show_Fail();
else
Show_Pass();
return result;
}
Revision: 1.0
20
//===========================================================================
// Function : Show_Help()
// Input : -
// Change : -
// Return : -
// Description : Show Title string.
//===========================================================================
void Show_Help()
{
clrscr();
printf("GPIO Test utility for W83697HF\n\n");
printf("VCC GND\n");
pr
intf("GPIO0
迋迋迋
GPIO4\n");
printf("GPIO1
迋迋迋
GPIO5\n");
printf("GPIO2
迋迋迋
GPIO6\n");
printf("GPIO3
迋迋迋
GPIO7\n");
}
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
