CAME PST003 Installation guide

PST001

TWISTER SERIES

TRIPOD

TURNSTILE

English

EN

INSTALLATION MANUAL

119G3040EN

WARNING!

Important instructions for the safety of people:

READ CAREFULLY!

Foreword

• Use of the products must be restricted to its intended use

(i.e. that for which it was expressly built for). Any other use is

to be considered dangerous. Came Cancelli Automatici S.p.A.

is not liable for any damage resulting from improper, wrongful

or unreasonable use • Keep these warnings with the installa-

tion and use manuals issued with the automated system.

Before installing

(preliminary check: in case of a negative

outcome, do not proceed before having

complied with the safety obligations)

• Make sure that the parts you intend to automate are in

good working order, and that they are properly balanced

and aligned. Also, make sure that proper mechanical stops

are already in place • If the operator will be installed at a

height of less than 2.5 m from the ground or other access

level, check whether you will need any protections and/or

warnings • Any gate leaves, ﬁ tted with pedestrian entrances,

onto which you will install an operator, must have a blocking

mechanism when the gate is in motion • Make sure that the

opening of the automated gate is not an entrapment hazard

as regards any surrounding ﬁ xed parts • Do not mount the

operator upside down or onto any elements that may fold

under its weight. If needed, add suitable reinforcements at

the points where it is secured • Do not install onto gates on

either an upward or downward slope (i.e. that are not on ﬂ at,

level ground) • Check that any lawn watering devices will not

wet the gearmotor from the bottom up.

Installation

• Carefully section off the entire site to prevent unauthorised

access, especially by minors and children • Be careful when

handling operators that weigh more than 20 Kg (see installa-

tion manual). In such cases, employ proper weight handling

safety equipment • All opening commands (e.g. buttons, key

selectors, magnetic detectors, etc.) must be installed at least

1.85 m from the gate’s area of operation perimeter - or where

they cannot be reached from the outside of the gate. Also,

the direct commands (e.g. push button, or proximity devices,

etc.) must be installed at a height of at least 1.5 m and must

not be accessible to the public • All ‘maintained action’ com-

mands, must be placed where the moving gate leaves, transit

areas and driveways are completely visible • If missing, ap-

ply a permanent label that shows the position of the release

mechanism • Before delivering to the client, verify that the

system is EN 12453 (impact test) standard compliant. Make

sure that the operator has been properly adjusted and that the

safety and protection devices, as well as the manual release

are working properly • Where necessary and in plain sight,

apply the Warning Sings (e.g. gate plate).

Special instructions and

advice for users

• Keep the gate’s area of operation clean and clear of any

obstacles. Trim any vegetation that may interfere with the

photocells • Do not allow children to play with the ﬁ xed com-

mand devices, or in the gate’s area of operation. Keep any

remote control devices (i.e. transmitters) away from the chil-

dren as well • Frequently check the system, to see whether

any anomalies or signs of wear and tear appear on the moving

parts, on the component parts, on the securing points, on the

cables and any accessible connections. Keep any joints (i.e.

hinges) lubricated and clean, and do the same where fric-

tion may occur (i.e. slide rails) • Perform functional tests on

photocells and sensitive edges, every six months. Keep glass

panels constantly clean (use a slightly water-moistened cloth;

do not use solvents or any other chemical products) • If the

system requires repairs or modiﬁ cations, release the operator

and do not use it until safety conditions have been restored

• Cut off the power supply before releasing the operator for

manual openings. See instructions • Users are FORBIDDEN

to carry out ANY ACTIONS THAT THEY HAVE NOT BEEN

EXPRESSLY ASKED TO DO OR SO INDICATED in the manu-

als. Any repairs, modiﬁ cations to the settings and extraor-

dinary maintenance MUST BE DONE BY THE TECHNICAL

ASSISTANCE STAFF • On the periodic maintenance log, note

down the checks you have done.

Special instructions and

advice for all

• Avoid working near the hinges or moving mechanical parts

• Stay clear of the gate’s area of operation when in motion •

Do not resist the direction of movement of the gate; this may

present a safety hazard • At all times be extremely careful

about dangerous points that must be indicated by proper

pictograms and/or black and yellow stripes • When using

a selector or command in ‘maintained action’ mode, keep

checking that there are no people in the area of operation of

the moving parts. Do this until you release the command •

The gate may move at any time without warning • Always cut

the power when cleaning performing maintenance.

THIS PAGE LEFT INTENTIONALLY BLANK

#



#

Pag.

2

- Manual code:

119G3040

119G3040 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

4.1 Turnstile

4 Description

2.1 Intended use

1 Legend of symbols

This symbol shows parts to be read carefully.

This symbol shows parts related to safety.

This symbol shows what to tell users.

The TWISTER electromechanical turnstile is designed to select transit flows in high-volume passage areas, and in highly fre-

quented contexts like stadiums, airports, stations, public buildings and in any other places where high-volume flows need to be

regulated and/or selected

Any installation or use other than that shown in this manual is prohibited.

3 Reference Legislation

IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING: WRONG INSTALLATION MAY CAUSE SERIOUS INJURY, FOLLOW ALL INSTALLATION INSTRUCTIONS

THIS MANUAL IS EXCLUSIVELY MEANT FOR PROFESSIONAL INSTALLERS OR OTHER COMPETENT PERSONS

This product is designed and built by CAME Cancelli Automatici S.p.A. in compliance with the current safety legislation.

It allows passage in the desired direction of one person a time. By activating a command device, the mechanism releases the tripod

which rotates freely allowing people to pass through; the arms automatically return into place and the mechanism locks immediately

after a single passage, waiting for a new command.

The range includes:

001PST001 - Bi-directional electromechanical tripod turnstile AISI 304 steel with scotch-brite ﬁ nishing, complete with ocntrol board,

transponder sensors and high-luminosity LED bi-directional trafﬁ c light with display. Tripod automatic release in case of blackout.

Power: 230 V AC 50 / 60 Hz

Power Draw: 260 mA max

Insulation class: II

Protection rating: IP44

Weight: 60 Kg

The product being described herein complies with the following legislation: see compliance statement.

4.2 Technical Data

2 Intended use and limits

11

1

7

5

2

1

6

5

8

9

4

8

3

10

12

13

14

1200

950

750

250

195

ø 40

850

Pag.

3

-

Manual code

:

119G3040

119G3040 ver.

1.5

1.5 09/2010

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

4.4 Dimensions

4.3 Description of parts

Legs1.

Tripod2.

Steel body3.

Casing4.

Casing cover5.

Upper cover6.

Traffic-light with display7.

Transponder8.

Status display9.

Mechanism10.

Control panel11.

Cover lock12.

Screws and washers for fixing the legs13.

Screws for fixing the casing14.

EXIT

SWIMMING POOL

Pag.

4

- Manual code:

119G3040

119G3040 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Standard installation Against the wall installation

Multiple installation

Platform installation

5 Application examples

Warning: Turnstile-controlled exits cannot serve as emergency exits. Always have an emergency exit and one also for disabled

persons.

6 Installation

Only skilled, qualified staff must perform the installation, in full compliance of the current legislation.

6.1 Preliminary checks

Before installing the automated device, please:

• Set up a proper omnipolar cut-off device, with contacts more than 3 mm apart, and power source isolation;

• Set up proper tubing and conduits for the electrical cables to go through with enough protection from any mechanical damage;

•

Check that any connections within the container (made to give continuity to the protection circuit) have additional isolation

compared to the other internal power conductors.

Make sure you have all the tools and materials needed to carry out the installation in total safety and in compliance with current

legislation. The figures shows examples of installers’ tools.

6.2 Tools and equipment

Suggested distance

between turnstiles

SWIMMING POOL

2

1

3

4

5

6

Pag.

5

-

Manual code

:

119G3040

119G3040 ver.

1.5

1.5 09/2010

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

6.3 Standar installation

6.4 Setting up the turnstile

Warning: installation required two people. Use hoisting equipment to move and position the turnstile.

Do not lean on the turnstile until it is solidly anchored, to prevent it from toppling over.

1) Used the issued key to open the lock on the front part of the

turnstile.

Tripod turnstile1.

Trafﬁ c-light with display2.

Electric wiring connector block3.

Transponder for transit access4.

Protection handrail5.

Status displays6.

2)

Raise the cover carefully so as to gently remove the

metal strip from the display (traffic light).

1

2

1

2

Pag.

6

- Manual code:

119G3040

119G3040 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

4) Remove the top cover.

Note: Lift the cover slightly tor easy removal.

5) Remove the two screws that fix the casing to the legs.

6) Remove the protective casings by gently lifting them. Then,

extract the casings.

6) Use the supplied M10 x 60 screws and flat washer to secure

the three arms to the tripod hub.

7) Slide the tripod onto the pin that protrudes out of the body,

secure it using the screw cap and M8 x 20 screw.

200

870

ø11

ø40

10

0

Ø12 mm

Pag.

7

-

Manual code

:

119G3040

119G3040 ver.

1.5

1.5 09/2010

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

5) Insert the nogs into the holes.

6) Place the turnstile over the nogs and pass the cable duct

through the central hole.

Screw the turnstile to the ground using the ratchet spanner.

6.5 Preparing the site and fixing the turnstile to the ground.

1) Check that the floor where the turnstile is anchored is level

and without warping.

3) Drill the marked holes.

2) Depending on the size of the passage, decide where to

install the turnstile and any accessories that should be added,

marking the fixing holes with a pencil respecting the measure-

ments given in the drawing.

4) Set up corrugated tubes for cables to go through.

If the ground cannot be drilled use a platform (001PSPEBUL) for

fixing the turnstile and accessories.

L

N

+ E

-

EbA EbA EbI EbI

10

S2

S12EM432111

Pag.

8

- Manual code:

119G3040

119G3040 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

7 Electric cabling

Use the proper cable clamps to secure

the cables inside the box in the control

panel.

Threading the power supply (and that

of any accessories) cable through the

bottom plate of the turnstile leg.

Pass the cable through the hole in the

top of the turnstile leg.

Threading the power supply cable (al-

ternatively to the hole on the base plate)

through a cable gland at the bottom of

the turnstile leg.

Earth

Cable clamps

Hole

7.1 Cable types and sections

N.B. If the cable length differs to that shown in the table, determine cable section based on the actual power draw by the connected

devices and according to what is prescribed by law CEI EN 60304-1.

For sequential connections on the same line, length-measurements by the table must be converted on the basis of draw and actual

distances. To connect any products not mentioned in this manual, see documentation provided with said products.

Cable clamps

Connections Cable types

Cable length

1 < 10 m

Cable length

10 < 20 m

Cable length

20 < 30 m

Power to electrical panel 230 V

FROR CEI 20-22

CEI EN

50267-2-1

3G x 1,5 mm

2

3G x 1,5 mm

2

3G x 1,5 mm

2

Power to accessories 2 x 0,5 mm

2

2 x 0,5 mm

2

2 x 1 mm

2

Command and safety devices 2 x 0,5 mm

2

2 x 0,5 mm

2

2 x 0,5 mm

2

L

N

+ -

+ E

-

A B

GND

EbA EbA EbI EbI

10

S2

S12EM432111

6

7

8

9

15

14

3

2

4

5

11

10

12

13

1

16

Pag.

9

-

Manual code

:

119G3040

119G3040 ver.

1.5

1.5 09/2010

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

FUSE TABLE

To protect: Fuse rating:

Control board (line) 1,6A-F

Accessoriesi 1,6A-F

8.2 Main Components

Transformer1.

Transformer connection terminals2.

1.6A accessories Fuse3.

Endpoint connection terminal4.

1.6A line fuse5.

230 V AC control board power terminals6.

Terminals for connecting accessories and com-7.

mand systems.

electro-block connection terminal board8.

Not used terminal board 9.

Transponder connection terminals10.

R700 board connectors11.

Memory roll board connectors12.

Traffic-light display connection terminal13.

Functions programming buttons14.

RBM84 connection terminal15.

Signal LED16.

The control panel is powered by 230 V AC on terminals L-N, with

max frequency of 50/60Hz

The 24 V power supply is of the SELV type.

The command and control devices and accessories are 24 V D.C.

Warning! The accessories must not comprehensively exceed

35W.

All connections are quick-fuse protected, see table.

The functions and user interface are set and displayed on the

software-managed display.

8.1 General description

8 Control panel

The deﬁ nable command and control functionalities are:

- clock-wise activation;

- counter clock-wise activation;

- Stop command;

- emergency command.

WARNING: before doing any work inside the equipment, cut the

power mains.

10 11 1 2 3 4 EM 2 S1 S2

A

B

GND

A

B

GND

L

N

Pag.

10

10 - Manual code:

119G3040

119G3040 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Counter-clockwise activating button / (N.O. contact)

Release the tripod in an anti-clockwise direction. If

no other command is given, the turnstile relocks itself

automatically after the time set in the “F5” function.

Clockwise activating button / (N.O. contact)

Release the tripod in a clockwise direction. If no

other command is given, the turnstile relocks it self

automatically after the time set in the “F5” function.

RBM84 - Access control

Software for recording user movements and for managing

personalised permits according to the program given to

each single user.

9 Electrical connections

230 V AC power, 50/60Hz

frequency

Connect the earth to the terminal ﬁ tted on the turnstile.

9.1 Power

9.2 Optional devices

Panic button / (N.C. contact)

Activating the contact triggers total block of the

turnstile. Note: Short circuit if unused!

Emergency button / (N.C. contact)

Pressing the button allows the tripod to turn in both

directions.

Note: Short circuit if unused!

Terminals for powering 24 V AC accessories,

max 250 mA and 35 W

+

E

-

L1T

L2T

24V

0V

EbA EbA

EbI EbI

L

N

+ -

+ E

-

A B

GND

EbA EbA EbI EbI

10

S2

S1 2 EM 4 3 2 1 11

Pag.

11

11 -

Manual code

:

119G3040

119G3040 ver.

1.5

1.5 09/2010

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Endpoint

Clockwise activated trasponder / (N.O. contact)

Release the tripod in a clockwise direction. If no other com-

mand is given, the turnstile relocks itself automatically after

the time set in the “F5” function.

Counter- clockwise activated trasponder / (N.O. contact)

Release the tripod in an anti-clockwise direction. If no other

command is given, the turnstile relocks itself automatically

after the time set in the “F5” function.

Blue

White

Pink

Red

Electromagnet

Red

S1 - Red

GND - Black

Status displays

TSP00

White

Brown

Green

Transformer

9.3 Already connected devices

Trafﬁ c-light with display

#!.#%,,)!54/-!4)#)

1

2

1

2

Pag.

12

12 - Manual code:

119G3040

119G3040 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Decoder boards for

transponders

LThe R700 boardscommand the turnstile with (TZP00/LT001) proximity sensors and the memory roll to save and load any settings

including registered users on another board

The R700 and Memory Roll boards must be inserted when the power is disconnected.

9.5 Decoder boards

Once the power is connected, wait 10 seconds before proceeding with any operations

Memory roll

9.6 Fixing the side casings and cover

1) Remount the side casing following the procedure given at point

6 on page 5 in reverse order.

2) Introduce the casings and screw them in place.

3) Introduce the top cover and connect the strap to the traffic

light.

IMPORTANT: before proceding with programming, make sure the electric cables are out of the way of the mechanical

parts.

{

< 00:00 >

F - 1

F - 2

F - 3

F - 4

F - 5

F - 6

F - 7

F - 8

F - 17

F - 16

F - 15

F - 14

F - 13

F - 12

F - 11

F - 10

F - 9

TSP2

TSP1

12 :30

Pag.

13

13 -

Manual code

:

119G3040

119G3040 ver.

1.5

1.5 09/2010

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

The ENTER button is for:

-entering the menu

-confirming or memorising the set value

The ESC button is for:

-exiting the menu

-cancelling the settings

Transponder to insert, modify and confirm functions via the Master card

without having to open the turnstile.

Position the Master card near the transponder receiver and carry out the

settings required which will be displayed step-by-step on the display.

10 Programming

10.1 Description of commands

The <> buttons are for:

- moving among menu items;

- increasing or decreasing a setting

Display to view the functions and settings that are assigned

via programming buttons or transponder

10.2 Menu structure

Creating the MASTER card

Creating a new card

Cancelling a card

Cancelling all of the cards

Inserting timeout time

Chosing the information-type on display

Cancelling the number of passages

Setting the number of passages

Setting the time and date

Data reading in the memory roll

Data recording in the memory roll

Differential entrance management

Antipassback mode (On or Off)

Setting the entrance direction

Periferal device number

Standalone or online mode

Enabling the Intrusion Buzzer

N.B. Functions F-2, F-3 and F-4 appear on the display only when the MASTER pass is generated.

Transponder used to

confirm the functions

and settings (ENTER)

Transponder used to

change, increase and

decrease a value (< >)

The functions can be programmed from the internal keypad on the control panel or from the Master pass.

Warning: to use the programming function, both display and transponder commands must be installed on the turnstile.

Also, all NC contacts, if unused, must be shortcircuited.

F - 1

F

-

2

---

F

-

1

F

-

2

F - 3

F

-

4

500

CLR-A

F - 4

F

-

5

F - 5

F

-

6

OFF

65000

F - 6

F

-

7

10:00

F - 3

1

3

2

500

1

3

2

500

CLR

10

12

11

60

F

-

2

F

-

3

F

-

4

F

-

5

Pag.

14

14 - Manual code:

119G3040

119G3040 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

10.3 Functions menu

Function 1: Creating the MASTER card

Creating the MASTER, activates the programming functions without opening the small-door.

See detailed function on pages 14 and 15.o.

Function 2: Creating a new card

Creating new cards (max. 500 cards)

See detailed fucntions on page 16.

Function 3: Cancelling a card.

Select the number of the pass that has to be cancelled using the keys or place the pass on the transponder (TSP1), the display

will show the pass number. Press ENTER to confirm cancellation.

Function 4: Cancelling all cards.

Cancelling all the cards memorised in the software.

Function 5: Setting the timeout time.

To set the time that the turnstile stays released after a button or transponder command (2-3 / 2-4).

The waiting time can be set between 10” and 60”.

Function 6: Chosing the type of information on the display.

Chosing the type of information to view on the display between the number of passages, the time or neither

Max 500 users

F - 10

F

-

11

65000

F - 7

F

-

8

CLR

OFF

F - 8

F

-

9

02

01

65000

12:00

2008

OFF

02

01

60

F - 11

F

-

12

OFF

ON

F - 12

F

-

13

1

3

2

60

:00 12:

31

07

12

Sto

ON

F - 9

F

-

10

F

-

9

F -

6

F

-

7

F

-

10

F

-

11

F

-

8

Pag.

15

15 -

Manual code

:

119G3040

119G3040 ver.

1.5

1.5 09/2010

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Function: Cancelling the number of passages

Cancelling the number of passages (entrance-exit) made by the turnstile

Function 8: Setting the maximum number of passages.

Setting the number of maximum passages allowed in the direction established by the “F-13” function.

From 1 to 65,000 passages or leave unlimited passages “OFF”.

Note: the number appearing on the display shows user presence at the entrance at that moment.

Function 9: setting the time and date.

Note: press the ENTER button until the datum you wish to change appears then press the <> buttons to increase or decrease the

datum, press ENTER until the automatic setting choice for daylight savings time (ON) or only set the GMT (OFF) time for the entire

year, confirm by pressing ENTER again.

Function 10: intrusion alarm Buzzer

Activating the buzzer in case of intrusion of deactivation. The activation time can be set between 1” and 60”.

Function 11: StandAlone or Online mode.

Stand-Alone (the turnstile works automatically – OFF) or On-Line (the turnstile is connected to and managed by the RBM84

access control system – ON).

Function 12: Periferal device number.

Assign to each turnstile (if more than one) a peripheral number (e.g. access control, etc.)

minutes

Hour

Days of the week, e.g.: 1 =

Monday, 2 = Tuesday, etc.

Day of the monthMonthyear

< ---

--- >

F - 14

F

-

115

F - 13

F

-

14

< OFF >

< ON >

000

F

-

16

F - 17

000

OFF

< -2- >

< -6- >

< -5- >

< -4- >

< -3- >

F - 15

F

-

16

< -1- >

F

-

13

F

-

12

F

-

14

F - 17

F-17

F - 16

F

-

15

Pag.

16

16 - Manual code:

119G3040

119 G3 04 0 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Function 13: Setting the direction for the passage counter.

Assign to the turnstile the direction for which the counter records the entrances set by function “F-8”. The flashing arrow indicated

the direction.

Function 14: Antipassback mode.

Activate or deactivate the Antipassback functions.

Prevents entering an area when the person is already inside. It can be used to prevent using the same pass for two or more conse-

cutive accesses to the same area: for example in a gym, to prevent clients entering with the personal pass of a client who is already

inside.

Funzione 16: Data recording in the memory roll.

It saves registered users and data settings in the memory roll.

Funzione 17: Data reading in the memory roll.

It loads registered users and data settings in the memory roll.

Intermittent arrow

Function 15: Differentiated passage mamangement.

Free = free passage for all users (Green Arrow).

Blocked = passage not allowed to all users (Red Arrow)

Controlled = passage allowed only to cleared users (Green Intermittent Arrow).

OFF = passaggio consentito solo a utenti abilitati su entrambe le direzioni (Freccie ros-

se).

Attention: when one of these 6 functions is activated, the antipassback function (Function 14)

and the maximum number of transits (Function 8) are deactivated.

12 :30

OFF Controlled Controlled

-1- Free Blocked

-2- Blocked Free

-3- Controlled Blocked

-4- Blocked Controlled

-5- Controlled Free

-6- Free Controlled

12 :30.

X2

F - 1

F - 2

OFF

F - 8

01

02

Sto

Clr

Pag.

17

17 -

Manual code

:

119G3040

119G3040 ver.

1.5

1.5 09/2010

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

10.5 Creating a master card

1) Press ENTER twice consecutively.

IMPORTANT: before actually creating the card, carefully read the instructions.

Follow the order of the following instructions otherwise the programming will not work.

To enter the functions menu, press

the ENTER button.

To choose the function, press

the arrows…

…then press ENTER

…then press ENTER to

confirm…

also for the the “sub-

menus”, move by using the

arrows … to raise or lower

a value.

Open the turnstile’s upper cover

and position it turned by 90° abo-

ve the body, so that the display

can be easily read. Open the

electrical oanel box to use the

programming buttons.

10.4 Browsing and programming the menu via the internal button console.

IMPORTANT: before doing any programming, carefully read the instructions.

Follow the order of the following instructions otherwise the programming will not work

…to modify increments, settings, creating cards, after confir-

ming with ENTER, “Sto” appears on the display.

…to cancel cards, number of passages, after confirming

with ENTER, “Clr” appears on the dislay.

Note: the flashing dot on the display shows that the Master

pass has not been generated yet.

----

Sto

F - 1

F - 2

TSP1

TSP2

TSP1

TSP2

TSP1

TSP2

TSP1

TSP2

Pag.

18

18 - Manual code:

119G3040

119G3040 ver.

1.5

1.5 09/2010 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

2) the “S1” LED transponder flashes RED and the lines will appear on the display.

3) Within 10 seconds, approach a the chosen MASTER card to the flashing transponder and leave it for several seconds until the

display shows the “Sto” (Storage) letters.

Intermittent Red LED

10.6 Browsing and programming the menu using the Master card.

1) To enter the function menu, place the Master pass on the transponder (TSP1). The display will show “F1”.

The transponder remains green throughout the programming time. Carrying out this operation is like keeping the “ENTER” button

pressed.

2)By moving the Master card, alternatively either right or left, or vice-versa, allows you to set the various functions without ope-

ning the turnstile.

Sensor used to confirm functions and

settings (ENTER)

Warning: always first create the MASTER card and keep it to be able to browse the functions menu.

Note: if the MASTER card is misplaced, follow the same procedure from point 1 using a new card.

red LED

green LED

Transponder (TSP2) used to change, increase or

decrease a value (endless loop system).

Intermittent Red LED

Page is loading ...

CAME PST003 Installation guide

This manual is also suitable for

CAME PST003 Installation guide

Related papers

Other documents