Gigabyte GA-8IR533 User manual

When you installing AGP card, please make sure the following

notice is fully understood and practiced. If your AGP card has

"AGP 4X notch"(show below), please make sure your AGP card is

AGP 4X (1.5V).

Do not use AGP 2X card (3.3V) in this motherboard. It will

burn and damage the motherboard due to Intel

®

845(E/G) / 850(E)

chipset can't support AGP 2X(3.3V).

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/

4X mode AGP slot. It can be switched between AGP 2X(3.3V) or

4X (1.5V) mode by adjusting the jumper. The factory default for this card

is 2X (3.3V). If you install this card in GA-8IR533 Series (or any AGP 4X

only) motherboards without switching the jumper to 4X mode (1.5V), it

will burn the motherboard.

Example 2: Some ATi Rage 128 Pro graphics cards made by “Power

Color”, the graphics card manufacturer & some SiS 305 cards, their

golden finger is compatible with 2X/4X mode AGP slot, but they support

2X(3.3V) only. If you install this card in GA-8IR533 Series (or any AGP

4X only) motherboards, it will burn the motherboard.

Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage

128 Pro chip, the design of AG32S(G) is compliance with AGP 4X (1.5V)

specification. Therefore, AG32S(G) will work fine with Intel

®

845(E/G) /

850(E) based motherboards.

M The author assumes no responsibility for any errors

or omissions that may appear in this document nor

does the author make a commitment to update the

information contained herein.

M Third-party brands and names are the property of

their respective owners.

M Please do not remove any labels on motherboard, this

may void the warranty of this motherboard.

M Due to rapid change in technology, some of the

specifications might be out of date before publication

of this booklet.

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-8IR533

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive

o EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment

o EN 61000-3-2*

T EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”

o EN 55013

Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment

o EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”

o EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

T EN 50081-1

Generic emission standard Part 1:

Residual commercial and light industry

T EN 50082-1

Generic immunity standard Part 1:

Residual commercial and light industry

o EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment

o EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment

o EN 55082-2

T EN 55022 Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus

o ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distribution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)

o EN50091-2

o EN 55020

o DIN VDE 0855

o part 10

o part 12

(EC conformity marking)

T CE marking

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use

o EN 60950

o EN 60065

Safety of household and similar

electrical appliances

o EN 60335

Manufacturer/Importer

Signature:

Name:

(Stamp)

Date : May. 17, 2002

T EN 60555-3

Timmy Huang

o EN 50091-1

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109

(a),Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible Party Name:

Address:

Phone/Fax No:

hereby declares that the product

Product Name:

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature:

Eric Lu

Supplementary Information:

Model Number:

17358 Railroad Street

City of Industry, CA 91748

G.B.T. INC. (U.S.A.)

(818) 854-9338/ (818) 854-9339

Motherboard

GA-8IR533

Date:

ERIC LU

May 17, 2002

USER’S MANUAL

GA-8IR533 Series

P4 Titan DDR Motherboard

Pentium

®

4 Processor Motherboard

Rev. 1004

12ME-8IR533-1004

2

GA-8IR533 Series Motherboard

Table of Content

Item Checklist ..................................................................................4

WARNING! .......................................................................................4

Chapter 1 Introduction .......................................................................5

Features Summary................................................................................................ 5

GA-8IR533 Series Motherboard Layout ............................................................ 7

Chapter 2 Hardware Installation Process ............................................8

Step 1: Install the Central Processing Unit (CPU) ........................................... 9

CPU Installation ........................................................................................... 9

CPU Heat Sink Installation ........................................................................... 10

Step 2: Install memory modules ....................................................................... 11

Step 3: Install expansion cards .........................................................................13

Step 4: Connect ribbon cables, cabinet wires, and powersupply .............. 14

Step4-1: I/O Back Panel Introduction ............................................................. 14

Step4-2: Connectors Introduction .................................................................. 16

Step4-3: Jumper Introduction ........................................................................ 22

Chapter 3BIOS Setup ..................................................................... 23

The Main Menu (For example: BIOS Ver. :F1) .............................................. 24

Standard CMOS Features .................................................................................26

Advanced BIOS Features ................................................................................... 29

Integrated Peripherals .......................................................................................31

Power Management Setup ................................................................................ 36

PnP/PCI Configurations ...................................................................................... 39

3

Table of Content

Q-Flash Introduction ...........................................................................................50

@ BIOS

TM

Introduction ........................................................................................ 52

Easy Tune

TM

4 Introduction ................................................................................ 53

Chapter 5 Appendix ........................................................................ 54

PC Health Status .................................................................................................. 40

Frequency/Voltage Control ................................................................................ 41

Top Performance ................................................................................................43

Load Fail-Safe Defaults ...................................................................................... 44

Load Optimized Defaults .................................................................................... 45

Set Supervisor/User Password .......................................................................... 46

Save & Exit Setup ................................................................................................. 47

Exit Without Saving ............................................................................................. 48

Chapter 4 Technical Reference ........................................................49

Block Diagram ..................................................................................................... 49

4

GA-8IR533 Series Motherboard

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

If the motherboard has mounting holes, but they don’t line up with the holes on the base and there are

no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting

holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful

of your hands). In this way you can still attach the motherboard to the base without worrying about short

circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard

PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the screw contact

any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the

board or cause board malfunctioning.

Installing the motherboard to the chassis…

WARNING!

þ The GA-8IR533 Series motherboard þ GA-8IR533 Series user’s manual

þ IDE cable x 1/ Floppy cable x 1 þ Quick PC Installation Guide

þ CD for motherboard driver & utility þ USB Cable 2 Port x 1

Item Checklist

5

Introduction

Form Factor — 19.6cm x 29.5cm ATX size form factor, 4 layers PCB.

Motherboard — GA-8IR533 Series include:

— GA-8IR & GA-8IR533

CPU — Socket 478 for Intel

®

Micro FC-PGA2 Pentium

®

4 processor

— Support Intel

®

Pentium

®

4 (Northwood, 0.13 m) processor

— Intel Pentium

®

4 400MHz FSB

— Auto detect and optimized setting for Pentium

®

4 processor

— 2nd cache depends on CPU

Chipset — Chipset Intel 845D HOST/AGP/Controller

— ICH2 I/O Controller Hub

Memory — 3 184-pin DDR DIMM sockets

— Supports PC2100 DDR or PC1600 DDR DIMM

— Supports up to 2GB DRAM (Max)

— Supports only 2.5V DDR DIMM

— Supports 64bit ECC type DRAM integrity mode

I/O Control — ITE8702

Slots — 1 AGP slot 4X (1.5V) device support

— 5 PCI slot supports 33MHz & PCI 2.2 compliant

On-Board IDE — 2 IDE bus master (DMA33/ATA66/ATA100) IDE ports for up to 4

ATAPI devices

— Supports PIO mode3,4 (UDMA 33/ATA66/ATA100) IDE & ATAPI

CD-ROM

On-Board Peripherals — 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes.

— 1 Parallel port supports Normal/EPP/ECP mode

— 2 Serial ports (COMA & COMB)

— 4 x USB 1.1 (2 by cable )

— 1 Front Audio connector

Chapter 1 Introduction

to be continued......

Features Summary

6

GA-8IR533 Series Motherboard

On-Board Sound — Realtek ALC650 CODEC

— Line Out / 2 front speaker

— Line In / 2 rear speaker(by s/w switch)

— Mic In / center & woofer(by s/w switch)

— SPDIF out : by s/w switch

— CD In / AUX In / Game port

PS/2 Connector — PS/2 Keyboard interface and PS/2 Mouse interface

BIOS — Licensed AWARD BIOS, 2M bit FWH

— Supports Q-Flash

Additional Features — PS/2 Keyboard password power on

— PS/2 Mouse power on

— STR(Suspend-To-RAM)

— AC Recovery

— USB KB/Mouse wake up from S3

— Poly fuse for keyboard,USB,game port over-current protection

— Supports @BIOS

— Supports EasyTune 4

Jumper less — Over Clock (CPU/DDR/AGP) by BIOS

Overclocking

Please set the CPU host frequency in accordance with your processor’s specifications.

We don’t recommend you to set the system bus frequency over the CPU’s specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Chipsets,SDRAM,Cards… .etc.

7

Introduction

GA-8IR533 Series Motherboard Layout

GA-8IR533

KB_MS

COMA

SPDIF

LPTGAME

LINE_IN

LINE_OUTMIC_IN

USB

ATX_12V

CD_IN

F_AUDIO

F_PANEL

BATTERY

SYS _FAN

ICH2

SOCKET478

CPU_FAN

ATX

FDD

IDE1

IDE2

ITE8702

PCI1

PCI2

PCI3

DDR2

DDR1

CODEC

F_USB1

CLR_CMOS

COMB

DDR3

BIOS

PCI4

PCI5

AUX_IN

SUR_CEN

CI

AGP

P4 Titan533

PWR_LED

845D

8

GA-8IR533 Series Motherboard

To set up your computer, you must complete the following steps:

Step 1- Install the Central Processing Unit (CPU)

Step 2- Install memory modules

Step 3- Install expansion cards

Step 4- Connect ribbon cables, cabinet wires, and power supply

Step 5- Setup BIOS software

Step 6- Install supporting software tools

Chapter 2 Hardware Installation Process

Step 2

Step 4

Step 3

Step 4

Step 1

Step 4

Step 1

9

Hardware Installation Process

Step 1: Install the Central Processing Unit (CPU)

CPU Installation

M Please make sure the CPU type is supported by the motherboard.

M If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause

improper installation. Please change the insert orientation.

Angling the

rod to 65

0

1. Angling the rod to 65-degree maybe feel a

kind of tight , and then continue pull the rod

to 90-degree w hen a noise “cough” made.

2. Pull the rod to the 90-degree directly .

Pin1 indicator

3. CPU Top View

Pin1 indicator

4. Locate Pin 1 in the socket and look

for a (golden) cut edge on the CPU

upper corner. Then insert the CPU

into the socket.

Socket

Actuation

Lever

10

GA-8IR533 Series Motherboard

CPU Heat Sink Installation

1. Hook one end of the cooler

bracket to the CPU socket first.

2. Hook the other end of the

cooler bracket to the CPU

socket.

M Please use Intel approved cooling fan.

M We recommend you to apply the thermal tape to provide better heat

conduction between your CPU and heatsink.

(The CPU cooling fan might stick to the CPU due to the hardening of the

thermal paste. During this condition if you try to remove the cooling fan, you

might pull the processor out of the CPU socket alone with the cooling fan, and

might damage the processor. To avoid this from happening, we suggest you to

either use thermal tape instead of thermal paste, or remove the cooling fan with

extreme caution.)

M Make sure the CPU fan power cable is plugged in to the CPU fan connector,

this completes the installation.

M Please refer to CPU heat sink user’s manual for more detail installation

procedure.

11

Hardware Installation Process

Step 2: Install memory modules

The motherboard has 3 dual inline memory module (DIMM) sockets, but it can only support a maximum

of 4 banks of DDR memory. DDR slot 1 uses 2 banks, DDR slot 2&3 share the remaining 2 banks.

Please refer to the following tables for possible memory configurations supported. The BIOS w ill

automatically detects memory type and size. To install the memory module, just push it vertically into the

DIMM Slot .The DIMM module can only fit in one direction due to the notch. Memory size can vary

between sockets.

Total Memory Sizes With Unbuffered DDR DIMM

Devices used on DIMM 1 DIMM x 64 / x 72 2 DIMMs x 64 / x 72 3 DIMMs x 64 / x 72

64 Mbit (2Mx8x4 banks) 128 MBytes 256 MBytes 256 MBytes

64 Mbit (1Mx16x4 banks) 32 MBytes 64 MBytes 96 MBytes

128 Mbit(4Mx8x4 banks) 256 MBytes 512 MBytes 512 MBytes

128 Mbit(2Mx16x4 banks) 64 MBytes 128 MBytes 192 MBytes

256 Mbit(8Mx8x4 banks) 512 MBytes 1 GBytes 1 GBytes

256 Mbit(4Mx16x4 banks) 128 MBytes 256 MBytes 384 MBytes

512 Mbit(16Mx8x4 banks) 1 GBytes 2 GBytes 2 GBytes

512 Mbit(8Mx16x4 banks) 256 MBytes 512 MBytes 768 MBytes

Notes: Double-sided x16 DDR memory devices are not support by Intel 845E/G chipset.

DDR1 DDR2 DDR3

S S S

D S S

D D X

D X D

S D X

S X D

D:Double Sided DIMM S:Single Sided DIMM

X:Not Use

12

GA-8IR533 Series Motherboard

M Please note that the DIMM module can only fit in one direction due to

the two notches. Wrong orientation will cause improper installation.

Please change the insert orientation.

DDR

1. The DIMM slot has a notch, so the

DIMMmemory module can only fit in one direction.

2. Insert the DIMM memory module verticallyinto the

DIMM slot. Then push it down.

3. Close the plastic clip at both edges of theDIMM slots

to lock the DIMM module.

Reverse the installation steps when you wish to

remove the DIMM module.

Established on the existing SDRAM industry infrastructure, DDR (Double Data Rate) memory is a

high performance and cost-effective solution that allows easy adoption for memory vendors, OEMs and

system integrators.

DDR memory is a sensible evolutionary solution for the PC industry that builds on the existing

SDRAM infrastructure, yet makes awesome advances in solving the system performance bottleneck by

doubling the memory bandwidth. DDR SDRAM w ill offer a superior solution and migration path from

existing SDRAM designs due to its availability, pricing and overall market support. PC2100 DDR

memory (DDR266) doubles the data rate through reading and writing at both the rising and falling edge of

the clock, achieving data bandwidth 2X greater than PC133 when running with the same DRAM clock

frequency. With peak bandwidth of 2.1GB per second, DDR memory enables system OEMs to build

high performance and low latency DRAM subsystems that are suitable for servers, workstations, high-

end PC 's and v alue desktop SM A sy stems. With a core voltage of only 2.5 Volts compared to

conventional SDRAM's 3.3 volts, DDR memory is a compelling solution for small form factor desktops

and notebook applications.

DDR Introduction

13

Hardware Installation Process

Step 3: Install expansion cards

1. Read the related expansion card’s instruction document before install the expansion card into

the computer.

2. Remove your computer’s chassis cover, screws and slot bracket from the computer.

3. Press the expansion card firmly into expansion slot in motherboard.

4. Be sure the metal contacts on the card are indeed seated in the slot.

5. Replace the screw to secure the slot bracket of the expansion card.

6. Replace your computer’s chassis cover.

7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.

8. Install related driver from the operating system.

AGP Card

Please carefully pull out the small white-

drawable bar at the end of the AGP slot when

you try to install/ Uninstall the AGP card.

Please align the AGP card to the onboard

AGP slot and press firmly down on the slot .

Make sure your AGP card is locked by the

small white- drawable bar.

14

GA-8IR533 Series Motherboard

Step 4: Connect ribbon cables, cabinet wires, and power

supply

Step4-1: I/O Back Panel Introduction

u PS/2 Keyboard and PS/2 Mouse Connector

PS/2 Mouse Connector

(6 pin Female)

PS/2 Keyboard Connector

(6 pin Female)

ØThis connector supports standard PS/2

keyboard and PS/2 mouse.

v USB Connector

ØBefore you connect your device(s) into USB

connector(s), please make sure your device(s)

such as USB keyboard, mouse, scanner, zip,

speaker..etc. Have a standard USB interface.

Also make sure your OS (Win 95 with USB

supplement, Win98, Windows 2000, Windows

ME, Win NT with SP 6) supports USB controller.

If your OS does not support USB controller,

please contact OS vendor for possible patch or

driver upgrade. For more information please

contact your OS or device(s) vendors.

w

x

v

u

y

USB 0

USB 1

15

Hardware Installation Process

x Game /MIDI Ports

Joystick/ MIDI (15 pin Female)

y Audio Connectors

ØThis connector supports joystick, MIDI keyboard

and other relate audio devices.

Ø After install onboard audio driver, you may

connect speaker to Line Out jack, micro phone to

MIC In jack. Device like CD-ROM , walkman

etc can be connected to Line-In jack.

w Parallel Port and Serial Ports (COMA/COMB)

ØThis connector supports 2 standard COM ports

and 1 Parallel port. Device like printer can be

connected to Parallel port ; mouse and modem

etc can be connected to Serial ports.

Line In

MIC In

Line Out

Parallel Port

(25 pin Female)

Serial Ports (9 pin Male)

COMA

COMB

16

GA-8IR533 Series Motherboard

Step4-2: Connectors Introduction

A) ATX I) F_USB1

B) FDD J) SPDIF

C) BATTERY K) SUR_CEN

D) SYS_FAN L) AUX_IN

E) CI M) CD_IN

F) IDE1/IDE2 N) CPU_FAN

G) PWR_LED O) F_AUDIO

H) F_PANEL P) ATX_12V

D

E

A

B

L

M

C

K

G

HI

F

J

N

O

P

Page is loading ...

Gigabyte GA-8IR533 User manual

Gigabyte GA-8IR533 User manual

Related papers

Other documents