Creative Broadband Blaster 8015U User manual

User’s Guide

Creative Broadband Blaster DSL Router 8015U

Information in this document is subject to change without notice and does not represent a commitment on the part of Creative

Technology Ltd. The software described in this document is furnished under a license agreement and may be used or copied only in

accordance with the terms of the license agreement. It is against the law to copy the software on any other medium except as

specifically allowed in the license agreement. The licensee may make one copy of the software for backup purposes. No part of this

manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and

recording, for any purpose without the written permission of Creative Technology Ltd.

Version 1.1

September 2004

Broadband Blaster is a trademark of Creative Technology Ltd.

IBM is a registered trademark of International Business Machines Corporation.

Intel and Pentium are registered trademarks of Intel Corporation

Microsoft, MS-DOS, Windows, and the Windows logo are registered trademarks of Microsoft Corporation.

Netscape Communicator is a trademark of Netscape Communications Corporation and may be registered outside the U.S.

All other products are trademarks or registered trademarks of their respective owners.

Contents

vi

Contents

Introduction

DSL Router information........................................................................................................................... 1-v

Package Contents....................................................................................................................................... 1-v

System requirements................................................................................................................................ 1-vi

Using Ethernet connection ........................................................................................................... 1-vi

Using USB connection.................................................................................................................... 1-vi

Using this document................................................................................................................................ 1-vii

1 About your DSL Router

2 Setting up your DSL Router using Ethernet connection

Setting up your DSL Router................................................................................................................... 2-2

Using the Ethernet port................................................................................................................. 2-2

Configuring your Network Interface Card ...................................................................................... 2-4

In Windows XP/Windows 2000................................................................................................. 2-4

In Windows Me/Windows 98 SE ............................................................................................... 2-7

3 Setting up your DSL Router using USB connection

Installing the USB Driver......................................................................................................................... 3-1

In Windows XP................................................................................................................................ 3-1

In Windows 2000 ............................................................................................................................ 3-5

In Windows Me................................................................................................................................ 3-7

In Windows 98 SE ........................................................................................................................... 3-9

vii

Setting up your DSL Router................................................................................................................. 3-12

Using the USB port ....................................................................................................................... 3-12

4 Configuring your DSL Router

Understanding DSL Router configurations........................................................................................ 4-1

Connecting to your DSL Router’s Home Page ............................................................................... 4-1

Configuring your DSL Router................................................................................................................ 4-3

PPPoA/PPPoE Configuration........................................................................................................ 4-3

RFC 1483 Routed IP Configuration.......................................................................................... 4-5

RFC 1483 Bridged IP Configuration .......................................................................................... 4-7

Disabling the Proxy Server ..................................................................................................................... 4-8

Using Internet Explorer................................................................................................................. 4-9

Disconnecting from the Internet........................................................................................................ 4-10

In PPPoA and PPPoE Mode ........................................................................................................ 4-10

In RFC 1483 Routed and Bridged Mode................................................................................ 4-10

Checking your DSL Router’s Status .................................................................................................. 4-10

Restoring Factory Default Settings..................................................................................................... 4-11

5 Configuring Advanced Features

LAN Settings ............................................................................................................................................... 5-1

DHCP Server Settings.............................................................................................................................. 5-1

LAN Client................................................................................................................................................... 5-2

Diagnostic Tests......................................................................................................................................... 5-3

Loopback Test .................................................................................................................................. 5-3

Ping Test ............................................................................................................................................. 5-3

DMZ Settings.............................................................................................................................................. 5-4

Port Forwarding......................................................................................................................................... 5-5

Universal Plug and Plug ............................................................................................................................ 5-5

Filtering.......................................................................................................................................................... 5-6

viii

IP Address Filtering ......................................................................................................................... 5-6

MAC Address Filtering .................................................................................................................. 5-7

Change Password ...................................................................................................................................... 5-8

Restore Factory Default Settings.......................................................................................................... 5-8

Firmware Upgrade .................................................................................................................................... 5-9

Appendixes

A Technical Specifications

B Troubleshooting

Connection to your DSL Router’s home page................................................................................ B-1

Connection to the Internet.................................................................................................................... B-2

LED Status.................................................................................................................................................... B-3

Normal Setup Status....................................................................................................................... B-3

Difficulties In Windows XP .................................................................................................................... B-5

C Frequently Asked Questions

D Glossary

Introduction

Introduction v

Introduction

Thank you for purchasing Creative Broadband Blaster DSL Router 8015U.

Developed with the most advanced Digital Subscriber Line (DSL) today, the DSL

Router provides you with high-speed broadband Internet connection using an

existing phone line. Enjoy speedy file transfers, watch Internet movies, video-

conference, and view videos without any long waits. You can also surf the Internet

and make a phone call at the same time!

Your DSL Router can be connected to your computer using a USB or Ethernet port.

Compliant with both ITU G.Lite and G.DMT, your DSL Router is capable of

Asymmetric Digital Subscriber Line (ADSL) full-rate operation up to 12 Mbps

downstream and 1 Mbps upstream, depending on your subscription with your

Internet Service Provider (ISP).

Your DSL Router is also capable of transmitting data at a higher rate using the

latest ADSL technology – ADSL2 and ADSL2+. ADSL2 can achieve downstream

data rate of up to 12Mbps, and ADSL2+ can achieve downstream data rate of up to

20Mbps (requires ISP with complementary infrastructure to support these

standards).

DSL Router

information

Before you begin, write down your DSL Router’s model and serial numbers found

at the bottom of your DSL Router.

Package

Contents

❑ Creative Broadband Blaster DSL Router 8015U

❑ USB cable

❑ Straight Ethernet cable

❑ RJ-11 phone cable

❑ Power adapter

❑ Installation CD

❑ Quick Start Leaflet

Introduction vi

❑ Microfilter

System

requirements

In order for your DSL Router to operate properly, be sure that your computer

meets the following minimum system requirements:

Using Ethernet

connection

❑ Installed Network Interface Card (NIC)

❑ CD-ROM drive for software installation

❑ Microsoft

®

Internet Explorer version 6.0

Using USB

connection

❑ Intel

®

Pentium

®

II 300 MHz or equivalent processor

❑ Microsoft Windows

®

XP, 2000, Me (Millennium Edition) or 98 SE (Second Edition)

❑ 20 MB of free hard disk space

❑ 32 MB RAM

❑ USB port

❑ CD-ROM drive for software installation

❑ Microsoft Internet Explorer version 6.0

You will need a hub if

you wish to connect

more than 2 computers

to your DSL Router.

Depending on your

computer’s

configurations, you can

choose to install your

router using the

Ethernet or USB port.

Introduction vii

Using this

document

These icons highlight useful or urgent information:

❍ Tip. This tells you about shortcuts or hints relating to a feature.

❍ Note. This highlights additional or important information about a

feature.

❍ Caution! This highlights proper usage of your device. Use this

information to avoid situations involving risk.

❍ Warning! This warns you of possible hazards to yourself or your device,

which may result in injury or damage.

About your DSL Router

About your DSL Router 1-1

About your DSL Router

This manual will guide you through the process of setting up your DSL Router.

Place your DSL Router in front of you as you go through this section to help you to

identify the various components of your modem.

LED Indication

POWER LED lights up when your DSL Router is connected to a power source.

READY

LED flashes when your DSL Router is initializing the DSL connection. LED

lights up when DSL connection is ready.

LINK

LED lights up when the Ethernet or USB port is connected to your

computer.

ACTIVITY LED flashes when there is data transfer to or from the Internet.

Figure 1-1: Front view of your DSL Router

Ready

LED

Activity

LED

Link

LED

Power

LED

About your DSL Router 1-2

Port/Connector Indication

PHONE PORT Connects to the telephone via a microfilter.

DSL LINE PORT

Connects to the telephone wall outlet using the

provided RJ-11 phone cable.

ETHERNET PORT

Connects to the Ethernet port on your computer

using the Straight Ethernet cable.

If you are connecting your DSL Router using the

Ethernet port, do not connect the USB port on the

same computer.

USB PORT

Connects to the USB port on your computer using

the USB cable.

If you are connecting your DSL Router using the

USB port, do not connect the Ethernet port on the

same computer.

RESET BUTTON

Resets your DSL Router’s settings to the factory

default settings.

POWER CONNECTOR

Connects to the power outlet using the provided

power adapter.

Figure 1-2: Back view of your DSL Router

DSL LINE

port

Ethernet

port

Reset button

Power

connector

USB

port

Phone

port

Setting up your DSL Router using

Ethernet connection

Setting up your DSL Router using Ethernet connection 2-1

Setting up your DSL Router using Ethernet connection

Depending on your computer’s configurations, you can choose to install your DSL

Router using the Ethernet or USB port on the same computer. Do not install your

DSL Router using both connections on the same computer.

If you are connecting your DSL Router using the USB port, skip this chapter and go

to

"Setting up your DSL Router using USB connection" on page 3-1.

Setting up your DSL Router using Ethernet connection 2-2

Setting up your

DSL Router

Using the Ethernet

port

Before setting up your DSL Router, be sure that the Network Interface Card in your

computer is installed and functioning properly.

Use Figure 2-1 as a reference when following these instructions to set up your DSL

Router.

1. Connect the straight Ethernet cable to the Ethernet ports on your computer

and DSL Router.

2. Locate a telephone wall outlet and unplug any telephone cable that is

connected to it.

DO NOT use the USB

port on your DSL

Router if you are using

the Ethernet port on

the same computer.

If you want more than

2 computers to have

access to your DSL

Router through a hub,

you may need to use a

crossed Ethernet cable

to connect your DSL

Router to the hub.

Consult your hub’s

manual for details.

Figure 2-1: Setting up your DSL Router using the Ethernet port

Telephone wall

outlet

RJ-11 cables

Power adapter

Ethernet

port

Ethernet port

Straight

Ethernet

cable

DSL LINE port

Power connector

Phone Port

Reset button

USB port

Microfilter

Setting up your DSL Router using Ethernet connection 2-3

3. Connect one end of the RJ-11 phone cable provided into the telephone wall

outlet.

4. Connect the other end into the DSL LINE port of your DSL Router.

5. Connect the small round plug of the power adapter provided to the DSL

Router’s power connector and plug your power adapter into a power outlet.

6. Turn on the power supply.

7. If you have telephones and fax machines sharing the same phone line,

connect them to the telephone wall outlet or your DSL Router phone port with

microfilters as shown below. The microfilters will help to ensure voice and data

quality.

Figure 2-2: Connecting a telephone to the telephone wall outlet

Telephone Wall

outlet

RJ-11

phone cable

Microfilter

Tele pho ne

Setting up your DSL Router using Ethernet connection 2-4

Configuring

your Network

Interface Card

Before using your DSL Router, you need to configure your Network Interface Card.

In Windows XP/

Windows 2000

1. After setting up your DSL Router, turn on

your computer.

2. In Windows XP, click Start -> Settings ->

Control Panel and double-click the

Network Connections icon.

In Windows 2000, click Start -> Control

Panel and double click the Network and

Dial Up Connections icon.

3. When the window similar to Figure 2-3

appears, right-click the Local Area

Connection icon, and then click

Properties.

If you are connecting

your DSL Router using

the USB port, skip this

chapter and go to

"Setting up your DSL

Router using USB

connection" on page 3-1.

Figure 2-3

Setting up your DSL Router using Ethernet connection 2-5

4. When the dialog box similar to Figure 2-4

appears, be sure that the name of your

network card is displayed in the first box.

5. In the list below the box, click the

Internet Protocol (TCP/IP) check box

to select it.

6. Click the Properties button.

Figure 2-4

Setting up your DSL Router using Ethernet connection 2-6

7. When the dialog box similar to

Figure 2-5 appears, click Obtain an IP

address automatically option, and

then click the OK button.

8. When the Local Area Connection

Properties dialog box appears, click

the OK button.

Before using your DSL Router, you will need

to configure your DSL Router. See

"Configuring your DSL Router" on page 4-1.

Figure 2-5

Page is loading ...

Creative Broadband Blaster 8015U User manual

Creative Broadband Blaster 8015U User manual

Related papers

Other documents