Sanyo Xacti VPC-GH3GX User manual

SERVICE MANUAL

Contents

1. OUTLINE OF CIRCUIT DESCRIPTION ............................... 3

2. DISASSEMBLY ................................................................... 10

3. ELECTRICAL ADJUSTMENT ............................................. 16

4. USB STORAGE INFORMATION REGISTRATION ............ 22

5. PARTS LIST........................................................................ 24

CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS...........C1

CAUTION : Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Discard used batteries according to the manufacturer’s instructions.

NOTE : 1. Parts order must contain model number, part number, and description.

2. Substitute parts may be supplied as the service parts.

3. N. S. P. : Not available as service parts.

Design and specification are subject to change without notice.

SG41K/U, EX, GX, PX, TA (R)

REFERENCE No. SM5310834

FILE NO.

Dual Camera

RoHS

•This product does not contain any hazardous substances prohibited by the RoHS

Directive.

WARNING

•You are requested to use RoHS compliant parts for maintenance or repair.

•You are requested to use lead-free solder.

(This product has been manufactured using lead-free solder. Be sure to follow the

warning given on page 2 when carrying out repair work.)

VPC-GH4

(Product Code : 168 306 01)

(U.S.A.) (Canada) (Taiwan)

(General) (South America)

VPC-GH3EX

(Product Code : 168 306 02)

(Europe) (U.K.) (Russia)

(Middle East) (Africa)

(General) (Korea) (Taiwan)

VPC-GH3GX

(Product Code : 168 306 03)

(China) (Hong Kong)

(General) (Korea)

VPC-GH3PX

(Product Code : 168 306 04)

(General) (Korea) (Taiwan)

(South America)

VPC-GH3TA

(Product Code : 168 306 05)

(Southeast Asia) (Australia)

(General)

– 2 –

WARNING

Do not use solder containing lead.

This product has been manufactured using lead-free solder in

order to help preserve the environment.

Because of this, be sure to use lead-free solder when carrying

out repair work, and never use solder containing lead.

Lead-free solder has a melting point that is 30 - 40°C (86 -

104°F) higher than solder containing lead, and moreover it does

not contain lead which attaches easily to other metals. As a

result, it does not melt as easily as solder containing lead, and

soldering will be more difficult even if the temperature of the

soldering iron is increased.

The extra difficulty in soldering means that soldering time will

increase and damage to the components or the circuit board

may easily occur.

Because of this, you should use a soldering iron and solder

that satisfy the following conditions when carrying out repair

work.

Soldering iron

Use a soldering iron which is 70 W or equivalent, and which

lets you adjust the tip temperature up to 450°C (842°F). It

should also have as good temperature recovery characteris-

tics as possible.

Set the temperature to 350°C (662°F) or less for chip compo-

nents, to 380°C (716°F) for lead wires and similar, and to 420°C

(788°F) when installing and removing shield plates.

The tip of the soldering iron should have a C-cut shape or a

driver shape so that it can contact the circuit board as flat or in

a line as much as possible.

Solder

Use solder with the metal content and composition ratio by

weight given in the table below. Do not use solders which do

not meet these conditions.

Lead-free solder is available for purchase as a service tool.

Use the following part number when ordering:

Part name: Lead-free solder with resin (0.5 mm dia., 500 g)

Part number: VJ8-0270

Metal content

Tin (Sn) Silver (Ag)

Copper (Cu)

Composition

ratio by weight

96.5 %

3.0 %

0.5 %

Note:

If replacing existing solder containing lead with lead-free sol-

der in the soldered parts of products that have been manufac-

tured up until now, remove all of the existing solder at those

parts before applying the lead-free solder.

The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of

special significance to product safety. Should any component designated by a symbol need to be replaced, use only the part

designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.

PRODUCT SAFETY NOTICE

– 3 –

1. OUTLINE OF CIRCUIT DESCRIPTION

1-1. CMOS CIRCUIT DESCRIPTION

1. IC Configuration

The CMOS peripheral circuit block basically consists of the

following ICs.

IC911 (MT9J003I12STCV)

CMOS imager

CDS, AGC, ADC built-in

H driver, V driver, serial communication circuit built-in

2. IC911 (CMOS)

[Structure]

The electric charges which are generated when each pixel is

optically converted are in turn converted into signal voltages

by the FD amplifier, and they are then transmitted by the built-

in H driver and V driver. The signals are sampled and ampli-

fied by the CDS and PGA circuits at the point they are output,

and then they are AD converted and output. The output uses

the 12 bit LVDS interface.

1/2.3-inch positive pixel array CMOS-type fixed imaging ele-

ment

Effective pixels 3664 (H) X 2742 (V)

– 4 –

1-2. CP1 and VF1 CIRCUIT DESCRIPTION

1. Circuit Description

1-1. Digital clamp

The optical black section extracts averaged values from the

subsequent data to make the black level of the sensor output

data uniform for each line. The optical black section averaged

value for each line is taken as the sum of the value for the

previous line multiplied by the coefficient k and the value for

the current line multiplied by the coefficient k-1.

1-2. Signal processor

1. γ correction circuit

This circuit performs (gamma) correction in order to maintain

a linear relationship between the light input to the camera and

the light output from the picture screen.

2. Color generation circuit

This circuit converts the image sensor into RGB signals.

3. Matrix circuit

This circuit generates the Y signals, R-Y signals and B-Y sig-

nals from the RGB signals.

4. Horizontal and vertical aperture circuit

This circuit is used gemerate the aperture signal.

1-3. AE/AWB and AF computing circuit

The AE/AWB carries out computation based on a 64-segment

screen, and the AF carries out computations based on a 6-

segment screen.

1-4. SDRAM controller

This circuit outputs address, RAS, CAS and CLOCK data for

controlling the SDRAM. It also refreshes the SDRAM.

1-5. PIO/PWM/SIO for LCD

It possible to switch between individual input/output and PWM

input/output.

1-6. TG/SG

Timing generated for image sensor control.

1-7. Digital encoder

It generates chroma signal from color difference signal.

2. Outline of Operation

When the shutter opens, the switch signal is input to ASIC and

CPU, and then operation starts. When the TG/SG drives the

image sensor, picture data is converted internally into a small-

amplitude actuating signal, and is then input to ASIC. The

data that is input to the ASIC is input to the SDRAM through

digital clamp.

The AF, AE, AWB, shutter, and AGC value are computed from

this data, and obtain the optimum picture. The data which has

already been stored in the SDRAM is read by the CPU and

color generation is carried out. Each pixel is interpolated from

the surrounding data as being either R, G, and B primary color

data to produce R, G and B data. At this time, correction of the

lens distortion which is a characteristic of wide-angle lenses is

carried out. After AWB and γ processing are carried out, a matrix

is generated and aperture correction is carried out for the Y

signal, and the data is then compressed by JPEG and is then

written to card memory (SD card).

When played back on the LCD and monitor, data is transferred

from memery to the SDRAM, and the image is then elongated

so that it is displayed over the SDRAM display area.

3. LCD Block

The LCD display circuit is located on the CP1 board, and

consists of components such as a power circuit.

The signals from the ASIC are 8-bit digital signals, that is

input to the LCD directly. The 8-bit digital signals are con-

verted to RGB signals inside the LCD driver circuit . This LCD

has a 3-wire serial, and functions such as the brightness and

image quality are controlled.

Because the LCD closes more as the difference in potential

between the VCOM (common polar voltage: AC) and the R,

G and B signals becomes greater, the display becomes darker;

if the difference in potential is smaller, the element opens and

the LCD become brighter.

In addition, the timing pulses for signals other than the video

signals are also input from the ASIC directory to the LCD.

– 5 –

5. Video Clip Recording and Playback

5-1. Recording

The signal from the camera block is input to IC101 (ASIC). The

data that is input to the ASIC is input to SDRAM, and converts

this data to encoded MPEG4 data, after which it is written in

sequence onto the SD card as streaming data. At this time,

the audio signals that are input to the built-in microphone are

converted into digital data by the audio CODEC IC of IC181,

and they are then input to ASIC. The audio data is then en-

coded (AAC), and then it is written in sequence onto the SD

card together as streaming data with the image signals de-

scribed above.

5-2. Playback

The data is read from the SD card, and the encoded data is

decoded into image data where it is displayed by the LCD or

on a TV monitor. At the same time, the audio data is also de-

coded, and is input to IC181 as digital data. D/A conversion is

carried out at IC181, and the sound is then output to the speaker

or to the LINE OUT terminal.

6. Audio CODEC Circuit (IC181)

The audio signals from the microphone are converted into 16-

bit digital data. AD conversion is carried out at a maximum

sampling frequency of 48 kHz.

During audio playback, the 16-bit digital data is converted into

analog signals and these are output to the speaker or line out

system. DA conversion is carried out at a maximum sampling

frequency of 48 kHz.

4. Lens drive block

4-1. Focus drive

The serial signals (LENS_SDATA, LENS_SCLK and

LENS_EN) and F_CLK which are output from the ASIC

(IC101) are used to drive (FOCUS_A+, FOCUS_A-,

FOCUS_B+ and FOCUS_B-) by the motor driver IC (IC951),

and then used to microstep-drive the focus stepping motor.

Detection of the standard focusing positions is carried out by

means of the photointerruptor (FOCUS_PI_E) inside the lens

block.

4-2. Zoom drive

The serial signals (LENS_SDATA, LENS_SCLK and

LENS_EN) and Z_CLK which are output from the ASIC

(IC101) are used to drive (ZOOM_A+, ZOOM_A-, ZOOM_B+

and ZOOM_B-) by the motor driver IC (IC951), and then used

to microstep-drive the zoom stepping motor. Detection of the

standard zooming positions is carried out by means of the

photointerruptor (ZOOM_PI_E) inside the lens block.

4-3. Iris drive

The serial signals (LENS_SDATA, LENS_SCLK and

LENS_EN) which are output from the ASIC (IC101) are used

to drive regular current (ND+ and ND-) by the motor driver IC

(IC951), and are then used to microstep-drive iris operation.

4-4. Shutter drive

The shutter drive signals (SHUTTER+) which are output from

the ASIC (IC101) are used to drive regular current (DRIVE+

and DRIVE-) by the motor driver (IC951), and then mecha

shutter is opened and closed.

– 6 –

7. Power Sequencer Description

For the overall configuration of the power sequenser, refer to the block diagram. This circuit block consists primarily of the power

sequencer block inside the ASIC.

The power sequencer have functions for receiving user operations which signify that the camera has been turned on and power

ON/OFF function.

Pin Signal

zSYRSTI

SYCKI

BATI

PON[1]

PON[0]

GPIOS[9]

GPIOS[8]

GPIOS[7]

GPIOS[5]

GPIOS[4]

GPIOS[3]

GPIOS[2]

GPIOS[1]

GPIOS[0]

KSO[4]

KSO[0]

KSI[3]

KSI[2]

KSI[1]

KSI[0]

BSRST

CLK32K

-

PON

-

SW3.2ON

PANEL_OPEN

ZCARD

KEY_1ST

KEY_2ND

ZUSB_DET

GREEN_LED

RED_LED

SCAN OUT0

SCAN_IN3

SCAN_IN2

SCAN_IN1

SCAN_IN0

I/O

I

O

I

O

I

Outline

Power sequencer block initializataion signal

32 kHz clock input

-

VDD1.1, VDD1.8, VDD3 control signal

-

SW3.2 V power ON/OFF control

LCD panel open/close detection

SD card detection

Key input 1st shutter

Key input 2nd shutter

USB detection

Green LED lighting control

Keyscan output signal

Keyscan input signal

Red LED lighting control

GPIOS[6]

DC_IN

I

DC jack input detection

KSO[3]

SCAN OUT3

O

Keyscan output signal

KSO[2]

SCAN OUT2

O

Keyscan output signal

KSO[1]

SCAN OUT1

O

Keyscan output signal

-

KSI[4]

SCAN_IN4 I

Keyscan input signal

Table 2-1. Power Sequencer Port Specification

– 7 –

8. Key Operation

For details of the key operation, refer to the instruction manual.

Table 2-2. Key Operation

0

123

SCAN

OUT

SCAN

IN

LEFT

VRECPOWER

1

2

DOWN

--

-

MENU

-

RIGHT

PLAY

UP

4

-

SET

ASIC/memory/LCD

CMOS

Power OFF

Play mode

VDD1.1, VDD1.8, VDD3

OFF

ON

Shooting mode

CMOS1.8, VAA2.8

ON

OFF

Table 2-3. Power Control

9. Power Supply Control

When the battery is attached, a AL3.2 V power is normally input to the power sequencer block, so that key scanning is carried out

even when the power switch is turned off, so that the camera can start up request again from user.

If the start up request is occured, the PON signal set to high, and then turns on the DC/DC converter.

In addition, the resetting of the CPU inside the ASIC is canceled. This causes all blocks and memories other than the power

sequencer of the ASIC to start operating.

When the power switch is turned off, the ASIC returns to the reset condition, all DC/DC converters are turned off and the power

supply to the whole system is halted.

3

WIDE ZOOMSEL

TELE

-

SUBREC

– 8 –

1-3. PWA POWER CIRCUIT DESCRIPTION

1. Outline

This is the main power circuit, and is comprised of the follow-

ing blocks.

Switching controller (IC501)

VAA 2.8 CMOS power output (L5041)

CMOS 1.8 CMOS power output (IC501 ch5)

VDD 3 power output (L5021)

VDD 1.8 power output (L5061)

VDD 1.1 power output (L5031)

LCD backlight system power output (L5071)

Motor system power BOOST 5.0 V output (L5301)

VDD 5 power output (IC502)

2. Switching Controller (IC501)

This is the basic circuit which is necessary for controlling the

power supply for a PWM-type switching regulator, and is pro-

vided with six channels, linear regulator one channel and load

switch one channel. This model is used six channels for switch-

ing regulator and one channel for load switch.

Only CH1 (BOOST 5.0 V), CH2 (VDD 3), CH3 (VDD 1.1),

CH4 (VAA 2.8), CH6 (VDD 1.8), CH7 (LCD backlight) and

CH5 (CMOS 1.8) are used.

Feedback from CH1 (BOOST 5.0 V), CH2 (VDD 3), CH3 (VDD

1.1), CH4 (VAA 2.8), CH6 (VDD 1.8) power supply outputs

are received, and the PWM duty is varied so that each one is

maintained at the correct voltage setting level.

Feedback for the CH7 (LCD backlight power) is provided to

the both ends voltage of registance so that regular current

can be controlled to be current that was setting.

CH5 (CMOS 1.8) is as source of CH6 (VDD 1.8) output so

that ON/OFF control can be carried out.

2-1. Short-circuit protection circuit

If output is short-circuited for the length of time determined

by IC501, all output is turned off. The control signal (P ON)

are recontrolled to restore output.

3. VAA 2.8 Power Output

VAA 2.8 (2.8 V) is output. Feedback for the VAA 2.8 is pro-

vided to the switching controller (Pin (G3) of IC501) so that

PWM control can be carried out.

4. CMOS 1.8 Power Output

CMOS 1.8 (1.8 V) is output. +1.8 V (D) is as source of VDD

1.8 power so that ON/OFF control can be carried out at IC501

ch5.

5. VDD 3 Power Output

VDD 3 (3.25 V) is output. Feedback for the VDD 3 output is

provided to the switching controller (IC501) so that PWM con-

trol can be carried out.

6. VDD 1.8 Power Output

VDD 1.8 (1.8 V) is output. Feedback for the VDD 1.8 output is

provided to the switching controller (Pin (G2) of IC501) so

that PWM control can be carried out.

7. VDD 1.1 Power Output

VDD 1.1 (1.1 V) is output. Feedback for the VDD 1.1 output is

provided to the switching controller (Pin (C6) of IC501) so

that PWM control can be carried out.

8. LCD Backlight Power Output

Regular current is being transmitted to LED for LCD back-

light. Feedback for the LED cathode is provided to the switch-

ing controller (Pin (B4) of IC501) so that PWM control to be

carried out.

9. Motor System Power Output

BOOST 5.0 V is output. Feedback for the BOOST 5.0 V out-

put is provided to the switching controller (IC501) so that PWM

control can be carried out.

10. HDMI VDD 5 Power Output

HDMI power VDD 5 (5 V) is output. Feedback for the VDD5

output is as source of BOOST 5.0 V power so that ON/OFF

control can be carried out at the IC502.

– 9 –

1-4. ST1 STROBE CIRCUIT DESCRIPTION

1. Charging Circuit

When UNREG power is supplied to the charge circuit and the

CHG signal from microprocessor becomes High (3.3 V), the

charging circuit starts operating and the main electorolytic

capacitor is charged with high-voltage direct current.

However, when the CHG signal is Low (0 V), the charging

circuit does not operate.

1-1. Charge switch

When the CHG signal switches to Hi, IC541 starts charging

operation.

1-2. Power supply filter

C5401 constitutes the power supply filter. They smooth out

ripples in the current which accompany the switching of the

oscillation transformer.

1-3. Oscillation circuit

This circuit generates an AC voltage (pulse) in order to in-

crease the UNREG power supply voltage when drops in cur-

rent occur. This circuit generates a drive pulse with a frequency

of approximately 200-300 kHz, and drive the oscillation trans-

former.

1-4. Oscillation transformer

The low-voltage alternating current which is generated by the

oscillation control circuit is converted to a high-voltage alter-

nating current by the oscillation transformer.

1-5. Rectifier circuit

The high-voltage alternating current which is generated at

the secondary side of T5401 is rectified to produce a high-

voltage direct current and is accumulated at electrolytic ca-

pacitor C5412.

1-6. Charge monitoring circuit

The functions programmed in the IC541 monitor oscillations

and estimate the charging voltage. If the voltage exceeds the

rated value, charging automatically stops. Then, the

CHGDONE signal is changed to Lo output and a "charging

stopped" signal is sent to the microcomputer.

2. Light Emission Circuit

When FLCTL signal is input from the ASIC, the stroboscope

emits light.

2-1. Emission control circuit

When the FLCTL signal is input to the emission control cir-

cuit, Q5402 switches on and preparation is made to the light

emitting. Moreover, when a FLCTL signal becomes Lo, the

stroboscope stops emitting light.

2-2. Trigger circuit

The Q5402 is turned ON by the FLCTL signal and light emis-

sion preparation is preformed. Simultaneously, high voltage

pulses of several kV are emitted from the trigger coil and ap-

plied to the light emitter.

2-3. Light emitting element

When the high-voltage pulse form the trigger circuit is ap-

plied to the light emitting part, currnet flows to the light emit-

ting element and light is emitted.

Beware of electric shocks.

– 10 –

26

25

28

32

31

34

33

12

29

24

35

20

14

13

18

11

19

17

18

16

10

21

2

E

B

C

22

23

16

1

F

15

3

4

6

5

D

3

A

8

9

27

7

30

2. DISASSEMBLY

2-1. REMOVAL OF CABI FRONT AND ST1 BOARD

NOTE: Discharge a strobe capacitor with the

discharge jig (VJ8-0188) for electric shock prevention.

When assembling,

tighten the screws order.

A → B → C → D → E → F

– 11 –

1. Screw 1.7 x 2.5

2. Screw 1.7 x 4.5

3. Four screws 1.7 x 4.5

4. Assy, cabi left

5. Cover BATT

6. Cover BATT inner

7. Adhesive dec back 4

8. Holder lens

9. Shaft strap

10. Remover the solder.

11. Screw 1.7 x 2.5

12. Screw 1.4 x 4

13. Assy, cabi front

14. Spacer flash top 2

15. Spacer chassis F2

16. Two screws 1.4 x 4

17. Assy, lamp SV

18. Spacer cabi front 3

19. Spacer cabi front 1

20. Spacer ring lens

21. Screw 1.4 x 4

22. Connector (CN541)

23. ST1 board

24. Screw 1.7 x 2

25. Screw 1.4 x 4

26. Assy, dec T B

27. Remover the solder.

28. Spacer speaker

29. Speaker, 8

30. Spacer lens left

31. Two screws 1.4 x 3

32. Spring zoom

33. Button sub movie

34. Button sub photo

35. Two screws 1.7 x 2

– 12 –

22

21

25

c

G

a

(

a

)

(

b

)

F

b

14

23

17

16

9

10

11

5

18

B

C

A

21

13

12

1

2

3

6

15

D

7

8

19

24

20

E

4

2-2. REMOVAL OF CABI RIGHT

1. Assy, heat sink L SV

2. Screw 1.4 x 4

3. Holder ST1

4. Spacer chassis F2

5. Spacer CP1 lens

6. Assy, FPC CA1 SV

7. Connector (CN901)

8. Connector (CN951)

9. Holder lens

10. Spacer flash lens

11. Spacer trigger

12. Spacer lens left

13. Spacer CA1 CN

14. Two screws 1.4 x 4

15. Two screws 1.4 x 4

16. Screw 1.7 x 3

17. Screw 1.7 x 3.5

18. Screw 1.7 x 2

19. Connector (CN103)

20. Spacer LCD harnss 2

21. Three screws 1.7 x 6

22. Dec joint

23. Two screws 1.7 x 3

24. Holder A joint

25. Compl, cabi right

When assembling,

tighten the screws order.

A → B → C → D → E → F → G

When assembling,

tighten the screws order.

(a) → (b)

When assembling,

tighten the screws order.

a → b → c

– 13 –

2-3. REMOVAL OF TB4 BOARD, TB3 BOARD, TB2 BOARD AND CP1 BOARD

6

5

4

18

19

3

7

12

23

24

1

11

8

9

2

27

25

10

A

C

B

28

22

20

21

17

16

14

15

13

26

When assembling,

tighten the screws order.

A → B → C

1. Connector (CN161)

2. Flexible PWB CP1-ST1

3. Spacer lens left

4. Spacer rubber zoom

5. Spacer TB3

6. Spacer TB3A

7. Remove the solder.

8. Remove the solder.

9. Remove the solder.

10. Three screws 1.4 x 4

11. Assy, heat sink R SV

12. Spacer CP1

13. Screw 1.4 x 4

14. Two screws 1.4 x 3

15. Earth TB3 TB4

16. Earth TB4

17. TB4 board

18. Screw 1.4 x 4

19. TB3 board

20. Screw 1.7 x 3.5

21. Connector

22. TB2 board

23. Two screws 1.4 x 4

24. CP1 board

25. Spacer lens right

26. Spacer CP1 lens

27. Assy, chassis

28. Terminal battery

– 14 –

18

20

19

23

27

28

22

24

B

A

C

17

25

3

26

2

17

15

13

11

10

7

1

8

12

21

6

14

4

5

16

9

2-4. REMOVAL OF TB1 BOARD, VF1 BOARD AND LCD

When assembling,

tighten the screws order.

A → B → C

When assembling

10

8

11

10

12

10

1. Screw 1.7 x 2

2. Two screws 1.7 x 4

3. Assy, cover LCD B

4. Remove the solder.

5. Connector (CN172)

6. Spacer MR

7. Cover joint B

8. Cover joint

9. Adhesive joint B

10. Spacer joint (removed after assembly)

11. Assy, joint

12. Assy, wire VF1 & CP1

13. Assy, magnet

14. Screw 1.7 x 2.5

15. TB1 board

16. Spacer TB1

17. Three screws 1.7 x 3

18. Compl, COV LCD FRT SV

19. Connector (CN171)

20. LCD

21. Spacer LCD

22. Spacer HL monitor

23. Three screws 1.7 x 2

24. Holder monitor

25. Earth MIC

26. Spacer earth MIC

27. VF1 board

28. Spacer MIC

– 15 –

2-5. BOARD LOCATION

VF1 board

TB1 board

CP1 board

ST1 board

TB2 board

TB4 board

TB3 board

– 16 –

3. ELECTRICAL ADJUSTMENT

3-1. Table for Servicing Tools

Download the calibration software and the firmware

from the following URL.

http://www.overseas.sanyo.com/dcamera service/

Place the DscCalDi.exe file, camapi32.dll file and

QrCodeInfo.dll file together into a folder of your

choice.

3-2. Equipment

1. AC adaptor

2. PC (IBM R -compatible PC, Windows 2000 or XP or Vista

or 7)

3-3. Adjustment Items and Order

1. Lens Adjustment (1 m)

2. Lens Adjustment (Infinity)

3. AWB Adjustment

4. White Point Defect Detect Adjustment

5. Black Point And White Point Defect Detect Adjustment In

Lighted

Note: If the lens, board and changing the part, it is necessary

to adjust again. Item 1-5 adjustments should be carried out in

sequence.

*Adjustment environment

Temperature: 25 ± 10 degrees

Humidity: 55 ± 25 %

3-4. Setup

1. System requirements

Windows 2000 or XP or Vista or 7

IBM R -compatible PC with pentium processor

USB port

40 MB RAM

Hard disk drive with at least 15 MB available

VGA or SVGA monitor with at least 256-color display

2. Pattern box

Turn on the switch and wait for 30 minutes for aging to take

place before using Color Pure. It is used after adjusting the

chroma meter (VJ8-0192) adjust color temperature to 3100 ±

20 K and luminosity to 900 ± 20 cd/m

2

. Be careful of handling

the lump and its circumference are high temperature during

use and after power off for a while.

3. Computer screen during adjustment

3-5. Connecting the camera to the computer

1. Use the supplied dedicated USB interface cable to connect

the camera to the computer.

2. Turn on the camera.

3. Choose the “COMPUTER”, and press the SET button.

Next, choose the “CARD READER”, and press the SET

button.

Ref. No.

Name

Part code

J-1

J-2

J-3

VJ8-0190

Pattern box

Calibration software

J-4

Number

1

Chroma meter

VJ8-0192

1

Spare lump (pattern box)

VJ8-0191

J-5

J-1 J-3

J-4

J-5

1

Discharge jig

VJ8-0188

J-6

1

Collimator

VJ8-0260

J-7

1

Spare lump (collimator)

VJ8-0282

J-8

1

Siemens star chart

J-8

Firmware

Data

AWB

Focus

UV Matrix

R Bright

RGB Offset

Tint

B Bright

Gain

Phase

LCD

Calibration

Upload

Initialize

LCD Type

H AFC Test

VCOMDC

VCOMPP

Cal Data

Cal Mode

OK

EVF

USB storage

Get

Set

VID

Set

PID

Set

Serial

Set

Rev.

Set

Setting

Language

Video Mode

VCO

Factory Code

Hall Cal.

Backrush pulse :

Set

Get

– 17 –

LENS

ASSY, FLEXIBLE PWB CA1

Preparation:

POWER switch: ON

Adjustment condition:

Siemens star chart (A3)

Fluorescent light illumination with no flicker

Illumination above the subject should be 700 lux ± 10%.

Note:

Do not vibrate during the adjustment.

If readjusting after it has already been adjusted, wait for 15

minutes or more for the unit to cool down first.

Adjustment method:

1. Set the siemens star chart 100 ± 0.5 cm from lens surface

so that it becomes center of the screen (zoom wide and

tele). Set the camera and the chart in a straight, and do not

put optical systems (mirror and conversion lens etc.)

2. Double-click on the DscCalDi.exe.

3. Click the “Focus”, and Click the “Ye s”.

4. Lens adjustment value will appear on the screen.

5. Click the OK.

2. Lens Adjustment (Infinity) is carried out after this ad-

justment.

3-8. Adjust Specifications

1. Lens Adjustment (1 m)

3-6. The adjustment item which in necessary in part exchange

COMPL PWB CP1

Factory

Cord

Setting

Language

Setting

COMPL PWB VF1

COMPL PWB ST1

COMPL PWB TB1

Reset

Setting

Lens

Adjust-

ment

(Infinity)

AWB

Adjust-

ment

USB

storage

information

registration

White Point

Defect

Detect

Adjustment

Black Point

And

White Point

Defect Detect

Adjustment

In Lighted

: Be sure to carry out the necessary adjustments after replacing the unit.

: Adjustment is possible from the menu setting screen of the camera and by using the calibration software.

COMPL PWB TB2

Lens

Adjust-

ment

(1 m)

3-7. Updating the firmware

Check the firmware version immediately after the CP1 board has been replaced. If an old version is being used, interfer-

ence and errors in operation may also occur. If an old version is being used, update it with a newer version.

Refer to

3-13. Firmware uploading procedure. (Page 21)

COMPL PWB TB4

COMPL PWB TB3

Camera

100 0.5 cm

Siemens

star chart

– 18 –

Preparation:

POWER switch: ON

If using a ready-made collimator, set to infinity.

Note:

Do not vibrate during the adjustment.

If readjusting after it has already been adjusted, wait for 15

minutes or more for the unit to cool down first.

Adjustment method:

1. Set the camera so that it becomes center of the siemens

star chart in the collimator (zoom wide and tele).

(Set a distance of 0.5-1.0 cm between camera lens and

collimator lens. Do not touch the each lens.)

2. Double-click on the DscCalDi.exe.

3. Select “Infinity Cal.” on the LCD “Test”, and click the “Ye s ”.

4. Lens infinity adjustment value will appear on the screen.

5. Click the OK.

Adjustment value determination is effectuated using below

values.

The adjustment values fulfill the conditions below, they are de-

termined as within specifications.

Adjustment value determination

AF_TEMP_AD: ATAD

ATAD: adjustment value of focus temperature A/D

(250<=ATAD<=893)

PZ_BR: PBR

PBR: adjustment value of zoom backrush pulse

(0<=PBR<=10)

AF_BR: ABR

ABR: adjustment value of focus backrush pulse

(0<=ABR<=10)

AF_I_WIDE: ZIW

ZIW: infinity adjustment value of focus at zoom position

wide (–90<=ZIW<=415)

AF_I_MID1: ZIM1

ZIM1: infinity adjustment value of focus at zoom position

middle1 (–567<=ZIM1<=169)

AF_I_MID2: ZIM2

ZIM2: infinity adjustment value of focus at zoom position

middle2 (–581<=ZIM2<=141)

Adjustment value determination is effectuated using below val-

ues.

The adjustment values fulfill the conditions below, they are de-

termined as within specifications.

Adjustment value determination

AF_WIDE: ZW

ZW: adjustment value of focus at zoom position wide

(–415<=ZW<=286)

AF_MID1: ZM1

ZM1: adjustment value of focus at zoom position middle1

(–169<=ZM1<=50)

AF_MID2: ZM2

ZM2: adjustment value of focus at zoom position middle2

(-141<=ZM2<=64)

AF_MID3: ZM3

ZM3: adjustment value of focus at zoom position middle3

(-133<=ZM3<=107)

AF_MID4: ZM4

ZM4: adjustment value of focus at zoom position middle4

(-175<=ZM4<=151)

AF_TELE: ZT

ZT: adjustment value of focus at zoom position tele

(–267<=ZT<=309)

2. Lens Adjustment (Infinity)

Camera

Collimator

DscCalDi x

OK

Focus Result

AF_WIDE: 0

AF_MID1: 42

AF_MID2: 56

AF_MID3: 84

AF_MID4: 109

AF_TELE: 165

!

Dsc Calibration x

OK

Infinity calibration :

AF_TEMP_AD: 464

PZ_BR: 3

AF_BR: 4

AF_I_WIDE: -3

AF_I_MID1: 8

AF_I_MID2: 13

AF_I_MID3: 21

AF_I_MID4: 30

AF_I_TELE: 48

Copy

– 19 –

Adjustment value determination is effectuated using the “WB”,

"CHECK" and "MS" values. If

WB = W1, W2, W3

CHECK = wc0, wc1, wc2

MS = ms1, ms2

the adjustment values fulfill the conditions below, they are

determined as within specifications.

Adjustment value determination

200<=w1<=310, 330<=w3<=500

wc0=128 ± 2, wc1=128 ± 2, wc2=150 ± 50

2000<=ms1<=4000, 2500<=ms2<=4500

Adjustment values other than the above are irrelevant.

4. White Point Defect Detect Adjustment

Preparation:

POWER switch: ON

Adjustment method:

1. Double-click on the DscCalDi.exe.

2. Select “CCD Defect” on the LCD “Test”, and click the “Ye s”.

3. After the adjustment is completed, OK will display.

4. Click the OK.

AF_I_MID3: ZIM3

ZIM3: infinity adjustment value of focus at zoom position

middle3 (–540<=ZIM3<=133)

AF_I_MID4: ZIM4

ZIM4: infinity adjustment value of focus at zoom position

middle4 (–456<=ZIM4<=175)

AF_I_TELE: ZIT

ZIT: infinity adjustment value of focus at zoom position

tele (–189<=ZIT<=267)

3. AWB Adjustment

Preparation:

POWER switch: ON

Setting of pattern box:

Color temperature: 3100 ± 20 (K)

Luminance: 900 ± 20 (cd/m

2

)

Adjusting method:

1. Set a distance of 0.5-1.0 cm between the pattern box and

the camera. (Do not enter any light.)

2. Double-click on the DscCalDi.exe.

3. Click the AWB, and click the Yes.

4. AWB adjustment value will appear on the screen.

5. Click the OK.

Camera

Pattern box

(color viewer)

Dsc Calibration

x

OK

AWB Results:

1:

WB=245,482,418

CHECK=128,129,138

MS=2556,2891

Fno_FOR_ISO=-1

SS_FOR_ISO=-1

YLEVEL_FOR_ISO=-1

Copy

– 20 –

5. Black Point And White Point Defect Detect

Adjustment In Lighted

Preparation:

POWER switch: ON

Setting of pattern box:

Color temperature: 3100 ± 20 (K)

Luminance: 900 ± 20 (cd/m

2

)

Adjusting method:

1. Set a distance of 0.5-1.0 cm between the pattern box and

the camera.

2. Double-click on the DscCalDi.exe.

3. Select “CCD Black” on the LCD “Test”, and click the “Ye s ”.

4. After the adjustment is completed, the number of defect

will appear.

5. Click the OK.

Camera

Pattern box

(color viewer)

3-9. Factory Code Setting

1. Check the "Factory Code" display within the Setting group.

2. For U.S.A., Canada and NTSC general area

If "FC_SANYO_U" does not appear, click on the " " mark

located on the right of the "Factory Code" display BOX and

select "FC_SANYO_U".

3. For Europe and PAL general area

If "FC_SANYO_EX" does not appear, click on the " " mark

located on the right of the "Factory Code" display BOX and

select "FC_SANYO_EX".

3-10. Language Setting

1. Click on the " " mark located on the right of the

"Language" display BOX.

2. Select language. (Default is English.)

3. End "DscCal" and remove the camera before turning the

camera power OFF.

3-11. Reset Setting

Carry out reset settings after replacing CP1 board.

1. Turn on the camera.

2. Set the NORMAL mode, and press the MENU button.

3. Choose the OPTION MENU 3.

4. Choose the RESET SETTINGS, and press the SET button.

5. Select YES, and press the SET button.

3-12. The Compulsive boot starting method

1. Keep the SHUTTER button depressed while switching on

the power.

2. Connect the camera and the computer with USB cable.

Firmware

Data

AWB

Focus

UV Matrix

R Bright

RGB Offset

Tint

B Bright

Gain

Phase

LCD

Calibration

Upload

Initialize

LCD Type

H AFC Test

VCOMDC

VCOMPP

Cal Data

Cal Mode

OK

EVF

USB storage

Get

Set

VID

Set

PID

Set

Serial

Set

Rev.

Set

Setting

Language

Video Mode

VCO

Factory Code

Hall Cal.

Backrush pulse :

Set

Get

Page is loading ...

Sanyo Xacti VPC-GH3GX User manual

This manual is also suitable for

Sanyo Xacti VPC-GH3GX User manual

Related papers

Other documents