Sharp 00ZFO3MKCUSME User manual

Brand: Sharp

Model: 00ZFO3MKCUSME

Category: Fax machines

Type: User manual

This manual is also suitable for

FO-3MK

1 - 1

FO-3MK

No. 00ZFO3MKCUSME

CONTENTS

MODEL FO-3MK

Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for

maintaining the safety and performance of the set.

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

SHARP CORPORATION

SERVICE MANUAL

FACSIMILE

OPTION MEMORY

UPGRADE PWB

[1] General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

[2] Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

[3] Diagnostic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

[4] Circuit schematics and parts layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

[5] Parts guide

This machine is an option memory unit applica-

ble to the machines FO-5700 (100V series).

FO-3MK

– 1 –

[1] General description

This machine is an option memory unit applicable to the machines

FO-5700 (100V series). It enhances the memory-aided functions such

as sequential simultaneous sending and through-memory sub-stitute re-

ception of facsimile.

[2] Installation procedure

(pay attention to static electricity)

To install the option memory unit, check the following in advance.

1) Make sure that the remaining memory capacity is 0%.

If the remaining memory capacity is not 0%, this implies that any data

remains in the image memory on the control PWB.

2) Check that a sufficient quantity of paper exists. If there is no paper or

paper is lacking, replenish the machine with paper, and print the data

received and stored in the memory.

3) Then, check whether there is any confidentially received information,

seeing the confidential reception data list ("FUNK" + "2" + "1" + "0"). If

any confidentially received information is found, input the ID No. of

specific reception box, and print the confidentially received informa-

tion.

4) After that, check whether there is timer sending information, seeing

the timer sending information list ("FUNK" + "2" + "0" + "2"). It is re-

quired to teach users that any timer sending information, if exists, is

cleared after the option memory unit is installed and, accordingly,

users have to set again the timer sending and do the timer sending.

Install the option memory unit in the following procedure.

1) Remove the ROM cover of facsimile.

2) Insert two spacers to control PWB, and then connect it to the connec-

tor CNOP of control PWB.

(Fig. 1)

3) Mount the control PWB to which the option memory has been con-

nected in the machine.

(Tighten the screws, and connect the connector without fail.)

4) Mount the ROM cover.

5) After installation turn on the power switch.

appears.

Then, after several seconds,

appears.

PLEASE WAIT A MOMENT

JUN

M:00% STAND BY AUTO

10 MON AM10:00

[3] Diagnostic mode

Successively input "FUNK" + "9" + " " + "8" + "#" + "7". Then,

appears.

After that, press the "START" key.

Then,

appears.

Select MEMORY CLEAR, using the one-touch key "11".

After completion of MEMORY CLEAR,

the following indication appears.

Select ROM/RAM test, using the one-touch key "03".

(This model is provided not only with flash memory for image but also

SRAM to enhance the function to store the number of transmissions

and receptions.)

When the "START" key is pressed again, the memory of machine

(control PWB) and memory of memory unit (excepting the flash mem-

ory) are checked.

An example of indication

After that, the indication shown below appears, and the result table

(Fig. 2) is printed.

After completion of ROM/RAM test the following indication appears.

Then, select the flash memory test, using the one-touch key "12".

In the diagnostic mode perform the image memory (standard, option)

write/read test, as well as complete erase test.

When the "START" key is pressed,

appears, and the indication changes from "–" to "■" whenever data is

written in the flash memory.

After completion of writing of data in all flash memories, the following

indication appears.

After that the long-tone buzzer (normal end) sounds, and at the same

time the following indication appears.

ROM:FAB0

( is ROM

version.)

01:

PRESS START KEY

SOFT SWITCH MODE

03:

PRESS START KEY

ROM RAM CHECK&

ROM CPU SRAM DRM

P P P P

(Upon occurrence of

error "E" appears.)

04:

PRESS START KEY

AUTO FEEDER MODE

12:

PRESS START KEY

FLASH MEMORY

S––E

TEST EXECUTING

11:

PRESS START KEY

MEMORY CLEAR

12:

PRESS START KEY

FLASH MEMORY

13:

PRESS START KEY

ALL ENTRYFAX/ TEL

FO-3MK

– 2 –

Then, the result table (Fig. 3) is printed.

In case of mismatch, the buzzer emits 9 short tones .

After that, the result table (Fig. 4) is output.

1) If any error occurred, check connection of connector CNOP (check

for bending and breakage of pin of connector), check that the option

memory unit has been mounted as specified, and then turn on again

the power supply, and check.

2) If the same error occurs persistently after the measures stated in item

1 above were taken, replace the option memory unit, and check.

3) If the same error occurs again after the measures stated in item 2)

were taken, check the control PWB.

Fig. 1

Fig. 2

Fig. 3

ROM/RAM CHECK LIST

MAIN: ROM = OK

= OK

VER.=FAB0X SUM =DE0E

SUM =1C86

VER.=FAB0A

P C U :

SRAM

DRAM

M/C=00

F/W=412250G001J0

CPU

OCT–19–1999 TUE 10:43 AM

FLASH MEMORY = OK (15S, 24S, 27S)

BANK CHANGEOVER = OK

BANK = OK

FLASH MEMORY CHECK REPORT

SIZE=5MB(With Option Flash memory)

OCT–19–1999 TUE 10:45 AM

CNOP

CONTROL PWB

OPTION MEMORY

PWB UNIT

FO-3MK

Fig. 4

FLASH MEMORY = NG (15S, 24S, 27S)

BANK CHANGEOVER = NG

BANK = NG

FLASH MEMORY CHECK REPORT

SIZE=5MB(With Option Flash memory)

OCT–19–1999 TUE 10:45 AM

FO-3MK

BDEFG

HCA

BDEFG

HCA

A19

A18

A17

A16

A15

A14

A13

A12

A11

A10

D15

D14

D13

D12

D11

D10

IC4

LH28F800SUT

8Mbit FLASH MEMORY

A20

DQ15

DQ14

DQ13

DQ12

DQ11

DQ10

DQ9

DQ8

DQ7

DQ6

DQ5

DQ4

DQ3

DQ2

DQ1

DQ0

CE0

CE1

/WE

/OPMWE

/OPMRD

DGDG

BYTE

3/5

RY/BY

DGDG

FLBK1

G2A

G2B

VCC

GND

+5V

/MWRH

/MRD

MA19

MA18

MA17

MA16

MA15

1A1

1A2

1A4

2A1

2A2

2A3

2A4

1A3

1Y1

1Y2

1Y4

2Y1

2Y2

2Y3

2Y4

1Y3

VCC

GND

+5V

C113

0.1

HRW0502A

MA11

MA10

MA9

MA8

MA7

1A1

1A2

1A4

2A1

2A2

2A3

2A4

1A3

1Y1

1Y2

1Y4

2Y1

2Y2

2Y3

2Y4

1Y3

VCC

GND

+5V

C110

0.1

MA12

MA13

MA14

CNOP-2

1A1

1A2

1A4

2A1

2A2

2A3

2A4

1A3

1Y1

1Y2

1Y4

2Y1

2Y2

2Y3

2Y4

1Y3

VCC

GND

C100

0.1

TCS2

R101

4.7K

TCS2

CNOP-7

Vcc 0

CNOP-1

CNOP-9

CNOP-3

CNOP-5

CNOP-50

+5V

C107

0.1

CNOP-26

CNOP-27

CNOP-28

CNOP-29

CNOP-30

IC1

74HC244

OCTAL BUFFERS

R129 91

R128 91

R127 91

R126 91

R125 91

A19

A18

A17

A16

A15

DG DG

CNOP-32

CNOP-31

CNOP-33

CNOP-34

CNOP-35

CNOP-36

CNOP-37

CNOP-38

R124 91

R123 91

R122 91

R121 91

R120 91

A14

A13

A12

A11

A10

R119 91

R118 91

R117 91

IC2

74HC244 OCTAL BUFFERS

IC3

74HC244 OCTUL BUFFERS

R115 91

R114 91

R113 91

R112 91

R111 91

R116 91 A6

MA5

MA4

MA3

MA2

MA1

MA6

CNOP-39

CNOP-40

CNOP-41

CNOP-42

CNOP-43

CNOP-44

GND 0

C10

22/16

C106

0.1

22/16

C105

0.1

+5V

A[19:0]

CNOP-45

FLBK4

R100

A19

A18

A17

A16

A15

A14

A13

A12

A11

A10

/OE

/FLS0

/OPMWE

/OPMRD

/FLBSY

TCS2

VPP

VCC

GND

GND 0

Vcc 0

R102

C116

0.1

C118

0.1

C101

0.1

C102

0.1

22/16

FLBK2

FLBK3

CNOP-47

CNOP-46

CNOP-49

CNOP-48

/FLOPT

/FLS0

/FLS1

/FLS2

/FLS3

/FLS4

/FLS5

/FLS6

/FLS7

IC6

74HC138

3-TO-8 LINE DECORDERS

A19

A18

A17

A16

A15

A14

A13

A12

A11

A10

D15

D14

D13

D12

D11

D10

IC5

LH28F016SUT

16Mbit FLASH MEMORY

A20

DQ15

DQ14

DQ13

DQ12

DQ11

DQ10

DQ9

DQ8

DQ7

DQ6

DQ5

DQ4

DQ3

DQ2

DQ1

DQ0

CE0

CE1

/WE

BYTE

3/5

RY/BY

FLBK4

A19

A18

A17

A16

A15

A14

A13

A12

A11

A10

/OE

VPP

VCC

GND

CNOP-45

TCS2

/FLBSY

CNOP-8

(*2)

/FLBSY

+5V

R103

4.7K

/FLS1

/OPMWE

/OPMRD

GND 0

Vcc 0

R104

C120

0.1

C122

0.1

C103

0.1

C104

0.1

22/16

CNOP-15

CNOP-16

CNOP-17

CNOP-18

CNOP-19

CNOP-10

CNOP-11

CNOP-12

CNOP-13

CNOP-14

CNOP-20

CNOP-21

CNOP-22

CNOP-23

CNOP-24

CNOP-25

D15

D14

D13

D12

D11

D10

D[15:0]

+5V

(2-6A)

(3-5E)

(*1)

(1-3F)

(1-2B)

(1-3C)(1-3F)(2-1A)

(2-1C)(2-1E)(2-4A)

(2-4D)(2-4F)

(1-2E)

(1-5C)

(*2) : (1-3C)(1-3F)

(2-1A)(2-1C)

(2-1E)(2-4A)

(2-4D)(2-4F)

(*2)

(1-2B)

(3-5B)(3-5F)

(1-2E)

(1-5C)

(1-4E)

(1-4H)

(2-4C)

(2-4E)

(2-4G)

(2-2C)

(2-2E)

(2-2G)

(*1) : (1-3E)(1-3H)(2-2C)(2-2E)

(2-2G)(2-4C)(2-4E)(2-4G)

N.M.

– 3 –

[4] Circuit schematics and parts layout

Option memory PWB circuit 1/3

Page is loading ...

FO-3MK

Option memory PWB parts layout (Top side)

Option memory PWB parts layout (Bottom side)

– 6 –

FO-3MK

[1] Packing parts

1 SPAKA110BXHZZ AB D Vinyl bag

2 SSAKA0006UCZZ AA D Vinyl bag

3 LSTY-0057AFZZ AC C Spacer

4 SPAKC285BXHZZ AD N D Packing case

5 PSHEM3490XHZZ AC D Aluminum foil

[2] Option memory PWB unit

1 VCEAPS226AF1C AC C Capacitor(16WV 22µF) [C4]

2 VCEAPS226AF1C AC C Capacitor(16WV 22µF) [C6]

3 VCEAPS226AF1C AC C Capacitor(16WV 22µF) [C8]

4 VCEAPS226AF1C AC C Capacitor(16WV 22µF) [C9]

5 VCEAPS226AF1C AC C Capacitor(16WV 22µF) [C10]

6 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C100]

7 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C101]

8 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C102]

9 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C103]

10 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C104]

11 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C105]

12 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C106]

13 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C107]

14 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C108]

15 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C109]

16 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C110]

17 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C113]

18 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C116]

19 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C118]

20 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C120]

21 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C122]

22 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C124]

23 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C126]

24 QCNCW2590SC5J AM C Connector(50pin) [CNOP]

25 VHDHRW0502A-1 AD B Diode(HRW0502A) [D1]

26 VHDHRW0502A-1 AD B Diode(HRW0502A) [D2]

27 VHIHD74HC244F AE B IC(HD74HC244), OCTAL BUFFERS [IC1]

28 VHIHD74HC244F AE B IC(HD74HC244), OCTAL BUFFERS [IC2]

29 VHIHD74HC244F AE B IC(HD74HC244), OCTAL BUFFERS [IC3]

30 VHILH28F80S10 BH B IC(LH28F800SUT), 8Mbit FLASH MEMORY [IC4]

31 VHILH28F016SU BR B IC(LH28F016SUT), 16Mbit FLASH MEMORY [IC5]

32 VHIHD74HC138F AE B IC(HD74HC138), 3–TO–8 LINE DECORDERS [IC6]

33 VHILH28F016SU BR B IC(LH28F016SUT), 16Mbit FLASH MEMORY [IC7]

34 VRS-TS2AD472J AA C Resistor(1/10W 4.7KΩ ±5%) [R101]

35 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R102]

36 VRS-TS2AD472J AA C Resistor(1/10W 4.7KΩ ±5%) [R103]

37 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R104]

38 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R105]

39 VRS-TS2AD910J AA C Resistor(1/10W 91Ω ±5%) [R111]~[R129]

(Unit)

901 DCEKM473BXH03 BR N E Option memory PWB unit

[5] Parts guide

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PAR T

RANK

DESCRIPTION

SHARP CORPORATION

Communication Systems Group

Quality & Reliability Control Center

Higashihiroshima, Hiroshima 739-0192, Japan

Printed in Japan

9911-1834SS•IS•T

No part of this publication may be reproduced,

stored in a retrieval system, or transmitted in

any form or by any means, electronic, mechanical,

photocopying, recording, or otherwise, without

prior written permission of the publisher.

Sharp 00ZFO3MKCUSME User manual

Brand: Sharp

Model: 00ZFO3MKCUSME

Category: Fax machines

Type: User manual

This manual is also suitable for

FO-3MK

Download PDF

report

Sharp 00ZFO3MKCUSME User manual

This manual is also suitable for

Sharp 00ZFO3MKCUSME User manual

Related papers

Other documents