PAC SWI-CAN2 User manual

PAC
Brand
PAC
Model
SWI-CAN2
Type
User manual
Pacifi c Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705
[email protected] • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the SWI-CAN2 be held liable for consequential damages sustained in connection
with the SWI-CAN2. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in
relation to the SWI-CAN2 other than its replacement.
03-26-08
Steering Wheel CAN Databus Interface
Pacific Accessory Corporation
www.pac-audio.com
For use with SWI-X
9
1
23456
78
1011
Program Button
Press Steering
Wheel Button
Steering Wheel Interface
9
1
23456
78
1011
Accessory Output
+12volts 1amp max.
SWI-CAN2
Plug into SWI-X, SWI-JACK, SWI-PS or SWI-ECL2
6 - Pin Harness
Using a C2R Radio Replacement Interface
Connect to
Radio Specific
SWC Interface
The SWI-CAN2 Interface must be used with one of the following Steering Wheel Interface modules: SWI-
ECL2, SWI-JACK, SWI-PS or SWI-X. This Interface will interpret the SWC commands sent on a CAN data
BUS and output an analog signal which is then used by the SWI-ECL2, SWI-JACK, SWI-PS, or SWI-X to
control your aftermarket radio.
1
2
3
4
5
6
7
8
9
0
Vehicle Switch Setting:
The SWI-CAN2 interface
has a rotary switch on the
side. Please set the switch
according to the vehicle
application chart.
Connections: If using a C2R radio replacement kit, plug the 6-pin black connector into the provided SWI-CAN2 6-pin harness. If
a C2R radio replacement kit is not used cut off the 6-pin connector provided with the SWI-CAN2. The wire descriptions are -
• Black - Ground: Connect to vehicle’s ground wire.
• Red - Accessory 12v Output: Connect only to devices that need power. Do not connect to the vehicles wiring in any way.
• Yellow - Battery 12v: Connect to the vehicles battery 12v wire.
• White/Red - CAN (+) : Connect to the vehicles interior CAN + wire. Refer to vehicle application chart for location.
• White/Black - CAN (-) : Connect to the vehicles interior CAN - wire. Refer to vehicle application chart for location.
Programming: After all connections are made and the rotary switch is set, the SWI-CAN2 can be plugged into the vehicle. Follow
the programming steps provided with the radio specifi c steering wheel interface. The SWI version number will be #2. When using
the SWI-CAN2 interface the vehicle should be in the ignition position during programming. Only buttons that solely controlled the
radio prior to removal can be (or should be) programmed. The use of multi function buttons is not recommended.
Programming Notes on Reverse Side.
J1850
Class 2
VPW
Class 2
J1850
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Arbitration
EOD
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 0 0 0 11 1 0 1 1 11 0 0 1 0 0 1 1 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Class 2
Class 2
Class 2
Class 2
Class 2
Class 2
J1850
J1850
J1850
SWI-CAN2
CAN-Data BUS Steering Wheel Interface for
use with a SWI-ECL, SWI-JACK, SWI-PS or SWI-X
Vehicle Programming Tips:
• Audi -The rotary switches on the wheel should be rolled a minimum of 5-6 clicks per function. If the vehicle is equipped with
a Multi Function Display in the instrument panel, programming the left hand buttons may change the MFD settings as well as
changing the radio as programmed to do so.
• Chrysler/Dodge/Jeep (2004-2008) - If a C2R-CHY/2/3 radio replacement interface is used, the C2R-CHY/2/3’s Blue/White
wire must be connected to the radio’s remote trigger wire (usually Blue/White) and the radio MUST be installed and on during
programming. The information display in the gauge cluster (if present) should also show the compass during programming.
• Mercedes - When programming the SWC buttons, Audio should be displayed on the information display in the gauge cluster.
For older E (W210) and CLK (W208) vehicles the display should be blank. Mercedes-Can-2 connector is located behind the CD
changer in the center of the dash. The Can + wire color is Brown/Red and CAN - is Brown. The wires are next to each other and
should be twisted pair. The Mercedes-Can-3 connector is located at the radio control module (tuner/amplifier). The radio antenna
will identify that you are in the correct location (passenger foot well in case of SLK). The Mercedes-Can-4 connector is a sub
connector inside of the Dock-n-Lock radio connector. The CAN + wire is Brown/Red and the CAN - wire is Brown. These wires
are twisted pair and felt tape may need to be removed in order to locate.
• Sprinter - The information display in the gauge cluster should display Audio during SWC button programming.
  • Page 1 1
  • Page 2 2

PAC SWI-CAN2 User manual

PAC
Brand
PAC
Model
SWI-CAN2
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents