Korenix JetNet 5628G Series User manual

1

Korenix JetNet 5628G/5828G Series

IEC61850-3 Modular Managed Ethernet Switch

User Manual

Version 1.6

Oct. 2013

www.korenix.com

2

Korenix JetNet 5628G/5828G

Industrial Modular Managed Ethernet Switch

User’s Manual

Copyright Notice

Copyright  2006-2011 Korenix Technology Co., Ltd.

Reproduction in any form or by any means without permission is prohibited.

3

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interference

at his expense.

The user is cautioned that changes and modifications made to the equipment without approval

of the manufacturer could void the user’s authority to operate this equipment.

Index

1 Introduction ....................................................................................................................... 2

1.1 Overview .............................................................................................................. 2

1.2 Major Features ..................................................................................................... 4

1.3 Package List ........................................................................................................ 4

1.4 Optional Module ................................................................................................... 5

2 Hardware Installation ........................................................................................................ 6

2.1 Hardware Introduction.......................................................................................... 6

2.2 Wiring Power Inputs ............................................................................................. 9

2.3 Wiring Digital Input ............................................................................................... 9

2.4 Wiring Digital Output .......................................................................................... 10

2.5 Wiring Earth Ground .......................................................................................... 10

2.6 Choosing Fast Ethernet Module ........................................................................ 10

2.7 Mounting Fast Ethernet Module .......................................................................... 11

2.8 Wiring Fast Ethernet Ports ................................................................................. 12

2.9 Wiring Fiber Ports .............................................................................................. 12

2.10 Wiring Gigabit Combo Ports .............................................................................. 14

2.11 Wiring RS-232 Console Cable ........................................................................... 14

2.12 Rack Mounting Installation ................................................................................. 14

2.13 Safety Warming.................................................................................................. 16

3 Preparation for Management .......................................................................................... 17

3.1 Preparation for Serial Console ........................................................................... 17

3.2 Preparation for Web Interface ............................................................................ 18

3.3 Preparation for Telnet Console .......................................................................... 20

4 Feature Configuration ..................................................................................................... 23

4.1 Command Line Interface Introduction ................................................................ 24

4.2 Basic Setting (Y2011, 0604) .............................................................................. 29

4.3 Port Configuration .............................................................................................. 55

4.4 Network Redundancy......................................................................................... 66

4.5 VLAN .................................................................................................................. 85

4.6 Private VLAN ..................................................................................................... 95

4.7 Traffic Prioritization .......................................................................................... 102

4.8 Multicast Filtering ............................................................................................. 107

4.9 Routing .............................................................................................................. 113

4.10 SNMP ............................................................................................................... 141

4.11 Security ............................................................................................................ 145

4.12 Warning ............................................................................................................ 157

1

4.13 Monitor and Diag .............................................................................................. 166

4.12 Device Front Panel ............................................................................................. 182

4.13 Save to Flash ................................................................................................... 184

4.14 Logout .............................................................................................................. 185

5 Appendix ....................................................................................................................... 186

5.1 Pin Assignment of the RS-232 Console Cable ................................................ 186

5.2 Korenix SFP family .......................................................................................... 187

5.3 Korenix Private MIB ......................................................................................... 188

5.4 Revision History ............................................................................................... 189

5.5 About Korenix .................................................................................................. 190

2

1 Introduction

Welcome to Korenix JetNet 5628G/5828G Industrial Modular Managed Ethernet Switch

User Manual. Following topics are covered in this chapter:

1.1 Overview

1.2 Major Features

1.3 Package Checklist

1.1 Overview

JetNet 5628G/5828G is an IEC61850-3 Modular Managed Ethernet Switch, equipped with 4

on-board Gigabit RJ45 / MINI GBIC combo ports plus 3 modular slots for maximum 24 10/100

Base-TX Ports or 18 100Base-FX Fiber interfaces ports. The JNM5 series modules are flexible

for different port volume, media types and application needs.

JetNet 5628G/5828G, a special design for substation automation and industrial control

room, is compliant with the IEC61850-3, IEEE1613 high level environmental certifications.

JetNet 5628G/5828G has the capability of forwarding Data, GOOSE, SCADA message

without any loss or collision. JetNet 5628G/5828G also pass the NEMA TS-2 and EN50121-4

certification which are requested in Transportation and Railway market.

The advantage of choosing JetNet 5628G/5828G is that the switch supports on board 4

gigabit ports which allow users to trunk up to 8G uplink bandwidth or to form 2 independent

Gigabit rings. The 24 100M interface allows to form 12 100M rings for a reliable network

redundancy. This is the Korenix MultiRing redundancy design. The recovery time when ring

failure can still remains 10ms high performance.

The JetNet 5628G/5828G series also supports the advanced management, control and

security requirements in power substations and control rooms, such as the VLAN, QoS, IGMP,

layer 2/4 Access Control List, 802.1x, SNMP V3, LLDP, etc. The JetNet 5828G support Layer

3 routing features, such as static route, dynamic unicast routing protocols, RIP and OSPF,

dynamic multicast routing protocol, DVMRP and VRRP for router redundancy. With all the

layer 2 and layer 3 features complete the demand and greatly satisfy technicians’ requests.

The JetNet 5628G/5828G Series include below models with the different power input types.

The model name and power input type is listed as below.

JetNet 5628G IEC61850-3 24+4G Modular Managed Ethernet Switch

Power Input: 1 x 85-264VAC/88-370VDC, Standard AC Plug + 2 x 24/48VDC

JetNet 5628G-2AC IEC61850-3 24+4G Modular Managed Ethernet Switch with Dual AC

3

input, Power Input: 2 x 85-264VAC/88-370VDC, Standard AC Plug

JetNet 5628G-2HDC IEC61850-3 24+4G Modular Managed Ethernet Switch with Dual

88-370VDC input, Power Input: 2 x 85-264VAC/88-370VDC, 3 Pin Terminal Block

JetNet 5828G IEC61850-3 24+4G Layer 3 Modular Managed Ethernet Switch

Power Input: 1 x 85-264VAC/88-370VDC, Standard AC Plug + 2 x 24/48VDC

JetNet 5828G-2AC IEC61850-3 24+4G Layer 3 Modular Managed Ethernet Switch with

Dual AC input, Power Input: 2 x 85-264VAC/88-370VDC, Standard AC Plug

JetNet 5628G-R IEC61850-3 24+4G Modular Managed Ethernet Switch, Ethernet Ports

on the Rear panel

Power Input: 2 x 85-264VAC/88-370VDC, 6-pin Terminal Block

JetNet 5828G-R IEC61850-3 24+4G Layer 3 Modular Managed Ethernet Switch,

Ethernet Ports on the Rear panel

Power Input: 2 x 85-264VAC/88-370VDC, 6-pin Terminal Block

PWR 1

PWR 2

AC/HDC

Connector

Low

Voltage

DI/DO

5628G

5828G

85~264VAC

1x Standard

three-pronged AC

plug

2x DC

24/48V

2DI + 2DO

5628G-2AC/

5828G-2AC

85~264VAC

2x Standard

three-pronged AC

plug

2DI + 2DO

5628G-2HDC

85~264VAC

88~370VDC

85~264VAC

88~370VDC

2x 3 pin Terminal

Block

2DI + 2DO

5628G-R/

5828G-R

85~264VAC

88~370VDC

85~264VAC

88~370VDC

6 pin Terminal

Block

1 DO

Note: The PWR 1 and PWR2 can support both 85-264VAC and 88-370VDC High Voltage

DC input. The AC connector is standard three-pronged AC connector, the High Voltage DC

connector is 3-pin terminal block represent for L, N and PE. The LDC connector is a 4 pin

terminal block for dual input.

4

1.2 Major Features

Korenix JetNet 5628G/5828G has the below different models as below.

Feature

5628G

5628G-R

5828G

5828G-R

IEC 61850-3 Design

V

Ethernet Port on the Rear

V

On Board free 4G combo ports

V

3 Flexible Modules

V

Max. Ring

14

Multiple Spanning Tree Protocol

V

256VLANs

V

8 physical priority queues

V

Private VLAN, QinQ

V

Modbus/TCP

V

Layer 2+ ACL, 802.1x

V

SNMP, LLDP & JetView Pro NMS

V

Layer 3 Unicast Routing Protocols - RIP,

OSPF

V

Virtual Router Redundancy Protocol

V

Layer 3 Multicast Routing Protocols –

DVMRP (coming soon)

V

Advanced PIM-DM/SM (coming soon)

V

The detail spec is listed in latest datasheet. Please download the latest datasheet in

Korenix Web site.

1.3 Package List

Korenix JetNet 5628G/5828G Series products are shipped with following items:

JetNet 5628G/5828G (4G Combo on board, No Fast Ethernet modules, no SFP

transceivers)

Rack Mount Kit

Console Cable

Power Cord

Quick Installation Guide

Document CD

If any of the above items are missing or damaged, please contact your local sales

representative.

5

1.4 Optional Module

Additional Fast Ethernet Modules:

JNM5-8TX: 8 ports 10/100Base-TX module

JNM5-4TX/4SFP: 4 ports 10/100TX + 4 100FX-SFP Socket

JNM5–2SFP/4MSC: 2 ports 100Base-FX + 4 ports 100Base-FX/SC Multi-mode

JNM5–2SFP/4SSC: 2 ports 100Base-FX + 4 ports 100Base-FX/SC Single-mode

Notice: The system only allow Maximum 12 SC type Fiber Links within one Switch. Less

than 12 Fiber links is Korenix recommend in high temperature environment, especially

no- air condition environment.

6

2 Hardware Installation

This chapter includes hardware introduction, installation and configuration information.

Following topics are covered in this chapter:

2.1 Hardware Introduction

Dimension

Panel Layout

Bottom View

2.2 Wiring Power Inputs

2.3 Wiring Digital Input

2.4 Wiring Relay Output

2.5 Wiring Earth Ground

2.6 Choosing Fast Ethernet Module

2.7 Wiring Ethernet Ports

2.8 Wiring Fiber Ports

2.9 Wiring Gigabit Combo Ports

2.10 Wiring RS-232 console cable

2.11 Rack Mounting Installation

2.12 Safety Warming

2.1 Hardware Introduction

2.1.1 JetNet 5628G/5828G (Ethernet Ports on the Front) Series

LED

System LED

Color

Port LED

Color

PWR/AC 1, PWR/AC 2

Green On/Off

Port 1~8 (JNM5-8TX)

Green/Green Blinking

LDC 1, LDC 2 (DC Power)

Green On/Off

Port 1~8 (JNM5-4TX/4SFP)

Green/Green Blinking

RDY (System Ready)

Green On/Off

Port 1~6 (JNM5-2SFP/4MSC)

Green/Green Blinking

DI 1, DI 2 (Digital Input)

Green On/Off

Port 1~6 (JNM5-2SFP/4SSC)

Green/Green Blinking

R.M. (Ring Master)

Green On/Off

Port 25~28 (Gigabit RJ45)

Green/Green Blinking

DO 1, DO 2 (Digital Output)

Red On/Off

Port 25~28 (Gigabit SFP)

Green/Green Blinking

R.F. (Ring Failure)

Red On/Off

For one AC model, the PWR2/AC2 LED is always not light. For dual AC/HDC model, the

LDC1/2 LED is always not light.

7

Dimension

JetNet 5628G/5828G Industrial Modular Managed Ethernet Switch dimension (W x H x D)

is 44mm(H) x 431mm (W) x 376mm (D)

Panel Layout

The front panel includes 3 modular slots for Fast Ethernet Module.

4 On-Board Gigabit Combo Port which support 10/100/1000 Copper and Gigabit SFP.

Power switch is used when you want change modular or save power.

In the back of the switch, there are AC, HDC or LDC power input socket, Digital

Input/Output socket and RS232 console port.

8

2.1.1 JetNet 5628G-R/5828G-R (Ethernet Ports on the Rear) Series

LED

LED on the Front

Color

LED on the Module

Color

P1, P2 (Power LED)

Green On/Off

Port 1~8 (JNM5-8TX)

Green/Green Blinking

DO 1 (Digital Output)

Red On/Off

Port 1~8 (JNM5-4TX/4SFP)

Green/Green Blinking

R.S. (Ring Status)

Green: Ring state is normal

Green Flashing: Incorrect

configuration

Amber: Ring state is

abnormal

Amber Flashing: One of the

ring ports break has been

detected

Port 1~6 (JNM5-2SFP/4MSC)

Green/Green Blinking

Port 1-28

Green/Green Blinking

Port 1~6 (JNM5-2SFP/4SSC)

Green/Green Blinking

Note: Port 25-28 is gigabit combo port, there is no LED on the rear panel.

Dimension

JetNet 5628G-R/5828G-R Industrial Modular Managed Ethernet Switch dimension (W x

H x D) is 44mm(H) x 431mm (W) x 376mm (D)

Panel Layout

The front panel includes RS-232 console and LED information only.

The rear panel includes 3 modular slots for Fast Ethernet Module. 4 On-Board Gigabit

Combo Port which support 10/100/1000 Copper and Gigabit SFP. And 6-pin High

Voltage Power Input socket and 1 Digital Output socket

9

2.2 Wiring Power Inputs

JetNet 5628G/5828G provides 2 types power input, AC power input and DC power input.

The front power switch can switch off all the power input at the same time.

AC Power Input

Connect the attached power cord to the AC power input connector, the available AC

power input is range from 85-264VAC.

High Voltage Power Input

The power input support both 85-264VAC and 88-370VDC power input. Connect the

power cord to the PE for Protective Earth, L / V+ for LINE or V+, N/V- for Neutral or V-.

For high power input, tighten the wire-clamp screws to prevent DC wires from being

loosened is must.

The pin assignment sequence of JetNet 5628G-R/5828G-R is N, L, PE for Power input 1

and PE, N, L for Power Input 2.

DC Power Input

Follow below steps to wire JetNet 5628G/5828G redundant DC power inputs.

1. Insert positive and negative wires into V+ and V-

contacts respectively of the terminal block

connector

2. Tighten the wire-clamp screws to prevent DC

wires from being loosened.

3. Power 1 and Power 2 support power redundancy

and polarity reverse protection functions.

Note 1: It is a good practice to turn off input and load power, and to unplug power terminal

block before making wire connections. Otherwise, your screwdriver blade can

inadvertently short your terminal connections to the grounded enclosure.

Note 2: The range of the suitable DC electric wire is from 12 to 24 AWG.

Note 3: If the 2 power inputs are connected, JetNet 5628G/5828G will be powered from

the highest connected voltage. The unit will alarm for loss of power, either PWR1 or

PWR2.

2.3 Wiring Digital Input

JetNet 5628G/5828G provides 2 digital inputs. It allows users to connect the termination

units’ digital output and manage/monitor the status of the connected unit. The Digital Input

pin can be pulled high or low; thus the connected equipments can actively drive these

pins high or low. The embedded software UI allows you to read and set the value to the

connected device.

The power input voltage of logic low is DC 0~10V. Logic high is DC 11~30V.

10

Wire the digital input just like wiring the power input introduced in chapter 2.2.

The JetNet 5628G-R/5828G-R doesn’t support Digital Input.

2.4 Wiring Digital Output

JetNet 5628G/5828G provide 2 digital outputs and JetNet 5628G-R/5828G-R provide 1

digital output, also known as Relay Output. The relay contacts are energized (open) for

normal operation and will close for fault conditions. The fault conditions include power

failure, Ethernet port link break or other pre-defined events which can be configured in

JetNet 5628G/5828G UI.

The default (without power) state of the Digital Output is normal OPEN state. The

ON/OFF state is controlled by software configuration.

The JetNet 5628G-R and JetNet 5828G-R support both OPEN and CLOSE mode.

Follow the installation guide print in the panel to wire.

Pin No.

State

1

NO (Normal Open)

2

COM

3

COM

4

NC (Normal Close)

Loosen the Digital Output screw by screw drive, then tighten the screw after digital output

wire is connected.

Note: When installed the Digital Output in your environment, remember to check the

environment protection, like Surge protection of the connected device. The digital output

contact of the JetNet 5628G/5828G do not provide high level Surge protection, this should

be protected by connected device.

2.5 Wiring Earth Ground

To ensure the system will not be damaged by noise or any electrical shock, we suggest

you to make exact connection with JetNet 5628G/5828G with Earth Ground.

For AC input, the 3

pin include V+, V- and GND. The GND pin must be connected to the

earth ground.

For High Voltage DC (HVDC) input, PE is Protective Earth pin.

For DC input, loosen the earth ground screw by screw drive; then tighten the screw after

earth ground wire is connected.

2.6 Choosing Fast Ethernet Module

The JetNet 5628G/5828G provides several types of Fast Ethernet modules. There are 8

10/100Base-TX ports, 4 100Base-FX/SC ports plus 2 100Base-FX SFP and 4

10/100Base-TX plus 4 100Base-FX modules.

11

The module type includes:

The modular design is more flexible for purchasing, less storage of stock and field

installations. Once the distance is over 100 meters, users can exchange modules without

replacing device. The 3 modules allow you connect maximum 24 10/100Base-TX Copper

ports or maximum 18 100Base-FX Fiber ports.

As purchasing the JetNet 5628G/5828G, please confirm the media type and the port

volume. Discuss the need with your customer and advise them your plan for the media

ports is the consideration before purchasing the Ethernet module.

Note: The JetNet 5628G/5828G main board can support high temperature environment.

There is no limitation to connect up to 3 x JNM5-8TX modules. Should you want connect

the Fiber modules, please check the environment temperature first. The heat from the

fiber interface is much higher than copper, using wide-temperature SFP transceiver is

recommended. Korenix requests less than 12 Fiber connections within one JetNet

5628G/5828G box when install in high temperature environment, especially no- air

condition environment. Should you need more fiber connections in one field station,

please separate them to 2 or more JetNet 5628G/5828G box.

2.7 Mounting Fast Ethernet Module

2.7.1 Power down the switch or Turn off the front power switch of the 5628G/5828G

series.

2.7.2 Unlock the front plate of the slot and plug the Fast Ethernet Module into the

socket.

2.7.3 Turn the captive screw to lock the module.

2.7.4 After locked the modules,

turn on the switch.

Note: Each time when you

plug or exchange module,

be noticed that you

should turn off the power

first.

12

2.8 Wiring Fast Ethernet Ports

JetNet 5628G/5828G includes maximum 24 RJ-45 Fast Ethernet ports. The fast Ethernet

ports support 10Base-T and 100Base-TX, full or half duplex modes. All the fast Ethernet

ports will auto-detect the signal from connected devices to negotiate the link speed and

duplex mode. Auto MDI/MDIX allows users to connect another switch, hub or workstation

without changing straight through or crossover cables.

Note that crossover cables simply cross-connect the transmit lines at each end to the

received lines at the opposite end.

Straight-through Cabling Schematic

Cross-over Cabling Schematic

Note that Ethernet cables use pins 1, 2, 3, and 6 of an 8-pin RJ-45 connector. The signals

of these pins are converted by the automatic MDI-X function, as shown in the table below:

Pin MDI-X

Signals

MDI Signals

1

RD+

TD+

2

RD-

TD-

3

TD+

RD+

6

TD-

RD-

Connect one side of an Ethernet cable into any switch port and connect the other side to

your attached device. The LNK LED will light up when the cable is correctly connected.

Refer to the LED Indicators section for descriptions of each LED indicator. Always make

sure that the cables between the switches and attached devices (e.g. switch, hub, or

workstation) are less than 100 meters (328 feet).

The wiring cable types are as below.

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable, EIA/TIA-568 100-ohm (100m)

100 Base-TX: 2-pair UTP/STP Cat. 5 cable, EIA/TIA-568 100-ohm (100m)

1000 Base-TX: 4-pair UTP/STP Cat. 5 cable, EIA/TIA-568 100-ohm (100m)

2.9 Wiring Fiber Ports

100Base-FX-SC Fiber

The automatic MDI/MDI-X crossover function does not apply to fiber connections, as

these must be crossed over manually. To connect the fiber port on one switch to the fiber

port of another switch, simply cross-connect the transmit channel at each end to the

receive channel at the opposite end as illustrated in the figure below.

13

JNM5-2SFP/4MSC and JNM5-2SFP/4SSC provides four 100Base-FX ports with SC type

connectors (in multi-mode and single mode versions). Single-mode types have greater

distance capability than multi-mode types, but single mode cable is generally more

expensive.

A fiber segment using single-mode cable must use 9/125 or 10/125 micrometer

single-mode fiber cables. For single-mode, the connection distance can be up to 30 km.

A fiber segment using multi-mode must use 50 or 62.5/125 micrometer multi-mode fiber

cables. For multi-mode, the connection distance can be up to 2 km.

Small Form-factor Pluggable (SFP)

The SFP ports accept standard MINI GBIC SFP transceiver. But, to ensure system

reliability, Korenix recommends using the Korenix certificated Gigabit SFP

Transceiver. The web UI will show Unknown vendor type when choosing the SFP which

is not certificated by Korenix. The certificated SFP transceiver includes 100Base-FX

single/multi mode, 100/Gigabit BIDI/WDM, 1000Base-SX/LX single/multi mode ranger

from 550m to 80KM.

14

The way to connect the SFP transceiver is to Plug in SFP fiber transceiver fist. Cross-connect the

transmit channel at each end to the receive channel at the opposite end as

illustrated in the figure below. The SPF cage is 2x1 design, check the

direction/angle of the fiber transceiver and fiber cable when inserted.

Note: This is a Class 1 Laser/LED product. Don’t stare at the

Laser/LED Beam.

2.10 Wiring Gigabit Combo Ports

JetNet 5628G/5828G includes 4 RJ-45 Gigabit Ethernet ports. The speed of the gigabit

Ethernet port supports 10Base-T, 100Base-TX and 1000Base-TX. JetNet 5628G/5828G

also equips 4 gigabit SFP ports combo with gigabit Ethernet ports. The speed of the

gigabit SFP port supports 1000Full Duplex. The available gigabit SFP supports Gigabit

Single-mode, Multi-mode, BIDI/WDM single-mode and DDM SFP transceivers. (The

100Base-FX is not supported in gigabit combo ports.)

While connect both RJ-45 and SFP at a time, the SFP will be chosen as the active media.

2.11 Wiring RS-232 Console Cable

Korenix JetNet 5628G/5828G attaches one RS-232 DB-9 to DB-9 cable in the box.

Connect the DB-9 connector to the COM port of your PC, open Terminal tool and set up

serial settings to 9600, N,8,1. (Baud Rate: 9600 / Parity: None / Data Bit: 8 / Stop Bit: 1)

Then you can access CLI interface by console able.

Note: If you lost the cable, please contact with your sales or follow the pin assignment to

buy a new one. The Pin assignment spec is listed in the appendix.

2.12 Rack Mounting Installation

The Rack Mount Kit is attached inside the package.

15

2.1.1 Attach the brackets to the device by using the screws provided in the Rack

Mount kit.

2.2.2 Mount the device in the 19’ rack by using four rack-mounting screws provided by

the rack manufacturer.

When installing multiple switches, mount them in the rack one below the other. It’s

requested to reserve 0.5U-1U free space for multiple switches installing. This is

important to disperse the heat generated by the switch.

Notice when installing:

 Temperature: Check if the rack environment temperature conforms to the specified operating

temperature range.

 Mechanical Loading: Do no place any equipment on top of the switch

 Grounding: Rack-mounted equipment should be properly grounded.

 Fiber Port limitation: Maximum 12 Fiber ports are allowed to install under the highest

temperature. Wide-Temperature SFP transceiver is always suggested.

16

2.13 Safety Warming

2.2.1 The Equipment intended for installation in a Restricted Access

Location.

2.2.2 The warning test is provided in user manual. Below is the information:

”For tilslutning af de ovrige ledere, se medfolgende installationsvejledning”.

“Laite on liitettava suojamaadoitus-koskettimilla varustettuun pistorasiaan”

„Apparatet ma tilkoples jordet stikkontakt“

”Apparaten skall anslutas till jordat uttag”

Page is loading ...

Korenix JetNet 5628G Series User manual

This manual is also suitable for

Korenix JetNet 5628G Series User manual

Related papers

Other documents