Crivit EH-1430 Instructions For Use Manual

Ski & Snowboarding Helmet EH-1430

Laskettelu- ja lautailukypärä EH-1430

Skid- och snowboardhjälm EH-1430

Ski- og snowboardhjelm EH-1430

Ski- und Snowboardhelm EH-1430

INSTRUCTIONS FOR USE

For your own safety, we recommend that you read

these instructions carefully and observe them.

Make sure you keep the instructions for future reference!

Oman turvallisuutesi vuoksi suosittelemme, että luet tämän

käyttöohjeen huolellisesti ja myös noudatat sitä.

Säilytä se ehdottomasti myöhempää tarvetta varten!

För din egen säkerhet rekommenderar vi, att du läser igenom

och beaktar hela denna bruksanvisning. Det är viktigt, att du

sparar den för framtida bruk!

For egen sikkerhed anbefales det at læse og følge

brugsvejledningen samt alle sikkerhedsoplysninger på hjelmen.

Det er vigtigt, at du gemmer den, så du kan læse i den senere!

Zu Ihrer eigenen Sicherheit empfehlen wir Ihnen, diese

Bedienungsanleitung komplett durchzulesen und zu beachten.

Bewahren Sie sie unbedingt für späteres Nachlesen auf!

IAN: 66431

NWS-Service • Wragekamp 6 • D-22397 Hamburg

Produkt-Hotline 00800-88080808 (Mo.- Fr., 10:00 - 16:00 Uhr, gebührenfrei)

de@nws-service.com

A.Hofer • Loebersdorfer Str.42 • AT-2560 Berndorf

Produkt-Hotline 00800-88080808 (Mo.- Fr., 10:00 - 16:00 Uhr, gebührenfrei)

at@nws-service.com

Atlantic Forwarding Ltd. • Mühlemattstr. 22, C.P. No. 131

4104 Oberwil BL, Switzerland

Produkt-Hotline 00800-88080808 (Mo.- Fr., 10:00 - 16:00 Uhr, gebührenfrei)

ch@nws-service.com

www.nws-service.com

Delta-Sport HanDelSkontor GmbH

Wragekamp 6 • D-22397 Hamburg

Version: 2011/IV

1. PC helmet shell 6. Clip Closure

2. Damping layer 7. Ear cushions

3. Comfort padding 8. Chin strap

4. Ski goggles clip 9. Strap distributor clip

5. Adjustment wheel

1. PC-ulkokuori 6. Klipsilukko

2. Iskunvaimentava sisäkuori 7. Korvapehmusteet

3. Pehmusteet 8. Leukahihna

4. Hiihtolasien kiinnitin 9. Hihnasäädin

5. Säädin

1. Hjälm av PC-material 6. Cliplås

2. Stötdämpande skikt 7. Öronlappar med stoppning

3. Komfortstoppning 8. Hakrem

4. Clip för skidglasögon 9. Remmens clip

5. Vridknapp

1. PC-inderhjelm 6. Clips-lukning

2. Dæmpningslag 7. Ørebeskyttere

3. Komfortpolstring 8. Hagerem

4. Spænde til skibriller 9. Remfordeler-clips

5. Drejehjul

1. PC-Helmschale 6. Clipverschluss

2. Dämpfungsschicht 7. Ohrenpolster

3. Komfortpolsterung 8. Kinnriemen

4. Skibrillen-Clip 9. Gurtverteiler

5. Drehrad

IAN: 66431

PSB LOGISTICS MANAGEMENT LTD • UNIT B3 SITE B

THE BOWMAN CENTRE ARNCOTT, OX25 1NZ OXON

Product hotline 00800-88080808 (Mon.-Fri. 10am – 4pm, free phone)

gb@nws-service.com

SCIMITAR LOGISTICS • WESTBANK ROAD 14-16

BT 3 95 L BELFAST

Product hotline 00800-88080808 (Mon.-Fri. 10am – 4pm, free phone)

ie@nws-service.com

Petrasol • Lönnrotinkatu 20 • FIN-00120 Helsinki

Asiakaspalvelu +800-88080808 (ma-pe 10 - 16, maksuton)

fi@nws-service.com

Nils Grundstedt • Gröndalsvägen 161 • 11769 Stockholm

Produkt-Hotline 00800-88080808 (må-fr 10 - 16, utan avgift)

se@nws-service.com

SEATAINERS A/S • Park Allé 350C • DK-2605 Brøndby

Produkt-hotline 00800-88080808 (man-fre kl. 10 - 16, gratis)

dk@nws-service.com

www.nws-service.com

1

2

3

4

5

6

8

7

9

5

Instructions for use 6 - 12

Käyttöohje 13 - 19

Bruksanvisning 20 - 26

Brugervejledning 27 - 33

Bedienungsanleitung 34 - 40

6

Ski & Snowboarding Helmet EH-1430

Important information

Before using your new helmet please take a moment to read the

following instructions for its use and care.

This helmet was developed for skiing and snowboarding and is

manufactured using state of the art processes. However, even the

highest safety standards do not exclude the possibility of injury

in a serious accident. The impact may be so great that the helmet

will not oﬀer its wearer eﬀective head protection. Conformity with

the demands of Appendix II of the European directive 89 / 686 /

European Economic Community (and later modiﬁcations) as well as

with those of the harmonising technical norm class EN1077:2007 B

was certiﬁed by the oﬃcials responsible at the TÜV Süd Product

Service GmbH, Ridlerstraße 65, 80339 München, Notiﬁed Body No

0123. A Class A helmet is a high performance protective helmet for

skiers and snowboarders. A Class B helmet is a helmet for skiers and

snowboarders for which the requirements are a little less restrictive.

A Class B helmet can thus oﬀer more air circulation and comfort,

without giving up too much protection. Class A and class B helmets are

for alpine skiers, snowboarders and similar groups. Class A helmets

oﬀer comparatively more protection Class B helmets can oﬀer more

ventilation and allow better hearing. However, they protect a smaller

area of the head and give a lower measure of protection.

This ski helmet is suitable for use with ski goggles.

7

Be sure the ski goggles accurately ﬁt into the helmet opening and

doesn’t press into the bridge of your nose when the helmet is tightly

closed.

Safety instructions

• The helmet must fit securely and the chin strap must be firmly closed.

• Do not push the helmet onto your neck,

as then your forehead is not protected.

• Do not wear any head covering under

the helmet.

• Ensure that the airflow inside the helmet is not restricted.

• Do not make any changes to the helmet, its structure, or the

individual components.

• Do not paint the helmet or put stickers or labels on it.

• The helmet is designed to absorb the energy of even a light

collision by destroying some of its components. Should another

collision occur, protection can therefore no longer be guaranteed.

After an accident, the helmet must be replaced even if no external

damage is visible.

• Do not use petroleum-containing solvents or detergents to clean

either the interior or exterior of your helmet. Use pH-neutral soap

diluted in clean water, and rub it into the helmet carefully using

a soft cloth. Wipe dry with a fluff-free cloth. The ear cushions can be

cleaned with a little soap and a soft brush. The visor should be

cleaned with soap and water only, and left to air-dry. Do not expose

the visor to sources of heat!

8

• Only use genuine spare parts for your helmet.

• Do not allow children to wear this helmet while climbing

or playing as this carries a risk of strangulation.

Ear buds/headphones

Please follow these safety precautions when using ear buds or

headphones:

Danger!

• Never use headphones or ear buds while skiing!

•During ascent or while waiting be sure to keep the volume at a

level that allows you to hear all ambient noise and announcements.

• Not observing announcements e.g. of the mountain rescue service

may result in a life threatening situation!

• Be sure the cables is not bothersome or protrudes from your body.

Risk of strangulation if wires get caught e.g. on the lift or other

skiers.

• You may be unable to hear warning signals from snow groomers

and not hear or be oblivious to other skiers on the run, and your

sense of balance could be impaired.

9

Pure by HeiQ

®

Pure is an anti-bacterial silver-based odour-inhibitor for sports and

recreational garments. Developed and manufactured by the Swiss

High-Tech company HeiQ

®

.

The microﬁbres of the helm lining are treated with an innovative,

anti-bacterial silver technology. For centuries already silver has been

known its anti-bacterial eﬀect. HeiQ

®

has compounded these proper-

ties to eﬀectively and permanently prevent odours.

Adjusting the chin strap

The overall length of the chin strap is adjusted with loop. The length

of the chin strap can also be adjusted with the strap distributor clip.

Be sure the strap distributor is not bothersome. We recommend posi-

tioning it at the end of the ear pad.

ﬁg. 1

10

Function of the rotary wheel

(Headband width adjustment)

With the inﬁnitely variable rotary wheel you can adjust the helmet

to the size of your head in order to guarantee an optimum helmet

ﬁt. Push the rotary wheel in the direction of the top of the helmet to

adjust the width (ﬁg. 2).

(Headband height adjustment)

The height of the headband system can be individually adjusted.

There are 3 diﬀerent height settings.

Pull the headband system connection pin out of the EPS shell locking

points (ﬁg. 3). You can now set the headband system connection pin

in one of the two other height position locking points. Press the pin

into the locking point ﬁrmly so that you can hear and feel it click into

place.

ﬁg. 3

ﬁg. 2

tighten

loosen

11

Servicing and maintenance

Regular servicing and maintenance contributes to the safety and

preservation of the helmet.

• Always use pH-neutral soap diluted in clear water, and rub

carefully with a soft cloth. Afterwards wipe dry with a fluff-free cloth.

• The cushion can be cleaned with a little soap and a soft brush.

Ear cushions

• Hand wash below 30 °C.

• Allow to dry at room temperature.

Storage

When not in use, store the helmet in a dry and well ventilated place

at room temperature. Avoid sources of heat.

Disposal instructions

Dispose of the product and all its components through a licensed

disposal company or your municipal disposal facilities.

Please observe the current regulations. If in doubt, consult your

disposal facility about an environmentally friendly disposal.

Suggestions for purchase

• Choose your helmet by measuring the circumference of your head

with a ﬂexible tape measure. Always try on a couple of diﬀerent

sizes before buying. When wearing the helmet, the skin of your

temples should move with it.

30°C/86°F

12

• Make sure that the helmet does not move around too much when

the chin strap is open.

• The chin strap must ﬁt securely. It should sit comfortably under the

chin, as far back towards the neck as possible. Fasten it as tight as

possible. It is correctly ﬁtted when you ﬁnd it diﬃcult to insert your

ﬁnger between the chinstrap and neck, yet are still able to breathe

and swallow easily. Make sure that the helmet does not restrict

your movements, e.g. when turning your head to look behind you.

3 Years Warranty

The product was manufactured with the greatest care and regular

testing. This product comes with a 3-year warranty as of the date of

purchase. Please keep the receipt. The warranty only covers material

and production errors and will not cover improper or inappropriate

handling. Your legal rights, in particular statutory rights are not

restricted with this warranty. In the event of a warranty matter, please

contact us free of charge via our Service-Hotline or send us an

email. In any case, we will be more than happy to provide you with

personal advice. In the event of a warranty matter, defect parts can

be shipped cash on delivery to the indicated service-address in coor-

dination with our service-colleagues. Subsequently you will promptly

receive a new or repaired part free of charge. The warranty period

will not be extended due to any repairs based on warranty, statutory

guarantee or fair dealing. This also applies to replaced and repaired

parts. Any repairs required after the warranty has expired are

chargeable.

Page is loading ...

Crivit EH-1430 Instructions For Use Manual

Crivit EH-1430 Instructions For Use Manual

in other languages

Related papers

Other documents