ActionTec HPE400AVP Quick start guide

ActionTec
Brand
ActionTec
Model
HPE400AVP
Category
PowerLine network adapters
Type
Quick start guide
Note: An Ethernet port looks similar to a phone port but is slightly larger.
Step
1 Get the MegaPlug AV
200 Mbps Powerline Ethernet
Network Adapter from the box.
Step
5 Plug the other end of the
Ethernet Cable into an OPEN
Ethernet Port on your Broadband
Modem or Router.
Step
4 Plug the MegaPlug
Adapter into a Power Outlet.
Do NOT
plug the Adapter into a
power strip or wall outlet that uses
surge protection as the Adapter
may not work.
Flip this Quick Start Guide over to continue
NEXT
Step
2 Get one Ethernet Cable.
Step
3 Plug one end of the
Ethernet Cable into the Ethernet
Port on the bottom of the
MegaPlug Adapter.
Step
6 Get the MegaPlug AV
200 Mbps 4-Port Switch from the
box. You will connect the 4 Port
Switch to the device(s) that you
want to have Internet access.
Questions? Call 1-888-436-0657 (USA) Questions? Call 1-888-436-0657 (USA) Questions? Call 1-888-436-0657 (USA)
Step
7 Get the Black Power
Cord.
Step
10 Get the other
Ethernet Cable.
Step
8 Plug one end of the
Power Cord into the back of the
MegaPlug 4-Port Switch.
Step
9 Plug the other end into a
Power Outlet.
Do NOT
plug the Switch into a
power strip or wall outlet that uses
surge protection as the Switch
may not work.
Part No: 0530-0602-000 QS1024/0309
Broadband
Router
Quick Start Guide
This Quick Start Guide will walk you through the easy
steps to install your MegaPlug™ AV Powerline Ethernet Kit.
You will need the following items:
•
One MegaPlug™ AV 200 Mbps
Powerline Ethernet Network Adapter
•
One MegaPlug™ AV 200 Mbps
4-Port Switch
•
Two Ethernet Cables
•
One Black Power Cord
NEXT
Questions? Call 1-888-436-0657 (USA)Questions? Call 1-888-436-0657 (USA)
Step
13 Check the LEDs and
make sure both Link Lights turn
SOLID GREEN.
Congratulations!
You have successfully installed the MegaPlug AV Powerline Ethernet
Network Adapter and 4-Port Switch.
These adapters ship with a generic encryption key. If you would
like to change the key, go to www.actiontec.com/howto for
further instructions.If you require additional adapters for additonal
computers/devices, they may be added by following the same
steps in this guide.
Step
11 Plug one end of the
Ethernet Cable into an Ethernet
Port on the back of the
MegaPlug 4-Port Switch.
Step
12 Plug the other end of
the Ethernet Cable into the
device that you want to connect
to the Internet.
Model# HPE200AVP,
HPE400AVP
Note: You can repeat Steps 10 thru 12 for each device that needs to be connected
to the Internet.
Note: This Quick Start Guide shows you how to install the 4-Port Switch in a
location apart from your router/gateway (another room for example). If you need
additional Ethernet ports near the router/gateway, you can reverse the installation
order of the Powerline units (i.e., install the 4-Port Switch first, then install the
MegaPlug Adapter in another room).
  • Page 1 1
  • Page 2 2

ActionTec HPE400AVP Quick start guide

ActionTec
Brand
ActionTec
Model
HPE400AVP
Category
PowerLine network adapters
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents