ActionTec HPE400AVP Quick start guide

Brand: ActionTec

Model: HPE400AVP

Category: PowerLine network adapters

Type: Quick start guide

Note: An Ethernet port looks similar to a phone port but is slightly larger.

Step

1 Get the MegaPlug AV

200 Mbps Powerline Ethernet

Network Adapter from the box.

Step

5 Plug the other end of the

Ethernet Cable into an OPEN

Ethernet Port on your Broadband

Modem or Router.

Step

4 Plug the MegaPlug

Adapter into a Power Outlet.

Do NOT

plug the Adapter into a

power strip or wall outlet that uses

surge protection as the Adapter

may not work.

Flip this Quick Start Guide over to continue

Step

2 Get one Ethernet Cable.

Step

3 Plug one end of the

Ethernet Cable into the Ethernet

Port on the bottom of the

MegaPlug Adapter.

Step

6 Get the MegaPlug AV

200 Mbps 4-Port Switch from the

box. You will connect the 4 Port

Switch to the device(s) that you

want to have Internet access.

Questions? Call 1-888-436-0657 (USA) Questions? Call 1-888-436-0657 (USA) Questions? Call 1-888-436-0657 (USA)

Step

7 Get the Black Power

Cord.

Step

10 Get the other

Ethernet Cable.

Step

8 Plug one end of the

Power Cord into the back of the

MegaPlug 4-Port Switch.

Step

9 Plug the other end into a

Power Outlet.

Do NOT

plug the Switch into a

power strip or wall outlet that uses

surge protection as the Switch

may not work.

Part No: 0530-0602-000 QS1024/0309

Broadband

Router

Quick Start Guide

This Quick Start Guide will walk you through the easy

steps to install your MegaPlug™ AV Powerline Ethernet Kit.

You will need the following items:

•

One MegaPlug™ AV 200 Mbps

Powerline Ethernet Network Adapter

•

One MegaPlug™ AV 200 Mbps

4-Port Switch

•

Two Ethernet Cables

•

One Black Power Cord

Questions? Call 1-888-436-0657 (USA)Questions? Call 1-888-436-0657 (USA)

Step

13 Check the LEDs and

make sure both Link Lights turn

SOLID GREEN.

Congratulations!

You have successfully installed the MegaPlug AV Powerline Ethernet

Network Adapter and 4-Port Switch.

These adapters ship with a generic encryption key. If you would

like to change the key, go to www.actiontec.com/howto for

further instructions.If you require additional adapters for additonal

computers/devices, they may be added by following the same

steps in this guide.

Step

11 Plug one end of the

Ethernet Cable into an Ethernet

Port on the back of the

MegaPlug 4-Port Switch.

Step

12 Plug the other end of

the Ethernet Cable into the

device that you want to connect

to the Internet.

Model# HPE200AVP,

HPE400AVP

Note: You can repeat Steps 10 thru 12 for each device that needs to be connected

to the Internet.

Note: This Quick Start Guide shows you how to install the 4-Port Switch in a

location apart from your router/gateway (another room for example). If you need

additional Ethernet ports near the router/gateway, you can reverse the installation

order of the Powerline units (i.e., install the 4-Port Switch first, then install the

MegaPlug Adapter in another room).

ActionTec HPE400AVP Quick start guide

Brand: ActionTec

Model: HPE400AVP

Category: PowerLine network adapters

Type: Quick start guide

Download PDF

report

ActionTec HPE400AVP Quick start guide

ActionTec HPE400AVP Quick start guide

Related papers

Other documents