2. Genexis
  3. F2020

Genexis F2020 Installation guide

  • Hello! I've reviewed the Genexis FiberTwist-Series installation guide and am ready to assist you with any questions you may have about it. I can provide information about the device's installation process, the function of its buttons and ports, or help you understand the indicators. Let me know what you need.
  • How do I remove the Blind Cover?
    How do I remove the dust cap?
    How do I install the FiberTwist unit?
    What does a green LED indicator for the TV mean?
F
F
FiberTwist–Series
Installation Guide
Buton oveview Pot oveview
SCPC coupler
with shuter
Unlock buton
Remove FiberTwist or Blind Cover – press and
hold while wisting counterclockwise
LED dim buton
Dim LEDs – press and release to dim LEDs in
steps
Power pot
TV pot
SCPC coupler with shuter
F – Fiber pot not functional
F – Fiber pot functional
System
Green – system ok
O – power o
LED oveview
TV
Green – TV ok
O – no TV
Box contents
• Genexis FiberTwist (active device)
• Power adapter
• Label (self-adhesive)
• Installation Guide (this document)
Label position
The product label is positioned on the
back of the active device.
Preparation
Ensure there is a power socket
within reach of where the device
is being installed.
Important: Instructions need
to be followed precisely and
uninterrupted. This minimizes
the risk of damage to the iber
optic connectors, causing a severe
degradation of signal qualiy.
Dierent language versions of this document and additional product information
are availableon htps:genexis.euproductibewistdownloads
Installation guide
Remove Blind Cover (if present)
. Press and hold the unlock buton (see buton oveview).
. Rotate the Blind Cover counterclockwise till it blocks.
. Remove the Blind Cover from the baseplate (FTU) by pulling
it towards yourself.
. Store the Blind Cover in a safe place.
Remove dust cap
. Take the FiberTwist out of the box.
. The dust cap is connected to the red string
located on the rear of the FiberTwist.
. Remove the dust cap by pulling the red string.
. Store the dust cap in a safe place.
Twist!
. Place the FiberTwist on the FTU as shown in the picture below,
in a –degree angle.
. Rotate clockwise until it clicks into place.
. Make sure the FiberTwist is aligned squarely on the FTU,
each edge must line up directly with the FTU below.
Your FiberTwist is now installed!
Company Name
Genexis B.V.
Company Address
Lodewijkstraat a
 AC Eindhoven
The Netherlands
Name and title of authorized person
Maaten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven --
The Netherlands
Hereby, Genexis B.V. declares that the product FiberTwist-FF is in
compliance with Directives EU, EU, EU, Delegated
Directive  and Ecodesign Directive EC.
The full texts of the EU declaration of conformiy are available at the following
internet address: htps:genexis.euredt-F-F
EU Declaration of Conformiy
Connecting the FiberTwist
. If required, connect your television  set-top box to the TV pot with a coax cable.
. F only: open the blue shuter from the SCPC coupler, connect your iber
gateway to the SCPC pot using a iber patch cable.
. Connect the supplied power adapter to the FiberTwist and plug the adapter
into a power socket.
If at some point in the future it becomes necessay to uninstall the FiberTwist,
please place the Blind Cover back on the FTU immediately and put the dust cap
back on the FiberTwist.
Revision . - June  - Copyright ©  Genexis Netherlands B.V. All rights reseved.
Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves
the right to change, modify, transfer, or othewise revise this publication without notice.
/