EdenPURE
®
Bladeless Tower Fan/Heater
Instruction Manual
1
IMPORTANT
SAVE THESE INSTRUCTIONS
To ensure you get the best results
from your Tower Fan/Heater,
please read this manual first and
keep it for future reference. For
additional information, please call
1-800-225-6595.
2
T
Model: A5716
- 2 -
Thank you for purchasing our Bladeless Tower Fan/Heater.
To ensure best performance, please read the instruction manual carefully
before use.
SAVE THESE INSTRUCTIONS
Content
1. Safety and Maintenance -------------------------------------------------------------- 3
2. Specifications ---------------------------------------------------------------------------- 4
3. Parts and Features --------------------------------------------------------------------- 5
4. Operating Instructions ----------------------------------------------------------------- 5
5. Remote Control Instructions --------------------------------------------------------- 6
6. Care and Cleaning --------------------------------------------------------------------- 7
7. Troubleshooting Guide ---------------------------------------------------------------- 8
- 3 -
Important Safety Instructions
WARNING
IMPROPER USE OF THIS FAN/HEATER COULD RESULT IN RISK OF FIRE, ELECTRIC SHOCK,
AND INJURY TO PERSONS
WARNING
ANY REQUIRED SERVICE OTHER THAN FILTER MAINTENANCE SHOULD ONLY BE
PERFORMED BY AN AUTHORIZED SERVICE REPRESENTATIVE AND ANY
OTHER REPAIRS ATTEMPTED BY ANYONE OTHER THAN AN AUTHORIZED
SERVICE REPRESENTATIVE WILL VOID THE WARRANTY.
FOR AUTHORIZED SERVICE, CALL 1-800-225-6595 OR VISIT WWW.EDENPURESUPPORT.COM
WARNING
RISK OF ELECTRICAL SHOCK DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
Safety and Maintenance
1. Extreme caution is necessary when any fan/heater is used by or near children or invalids
and whenever the unit is left operating and unattended. Children should be under
supervision to ensure that they will not play with the fan as a toy.
2. Do not plug the tower into any other cord-connected device such as a power strip, surge
protector, multiple outlet adapter, grounding adapter or outlet-type air fresheners. Plug
into a 3-prong 120v 15amp or higher grounded circuit receptacle only. Do not plug
the tower into a loose-fitting or broken receptacle. The tower is for use on 120 volt outlets.
3. Always unplug tower when not in use. Don’t move the tower until you unplug it from the
outlet.
4. Don’t unplug by pulling on the cord. You should unplug and grasp the plug, not the cord.
5. Don’t operate the tower with a damaged cord or plug, or after it has been dropped or
damaged in any manner. In such cases, contact customer service to replace or repair if
it is damaged.
WARNING
To avoid fire, electric shock or personal injury, be sure to comply
with the following requirements.
- 4 -
6. Don’t stretch the cord or place the cord under strain. Keep the cord away from heat
sources.
7. Don’t run the cord under carpeting. Don’t cover the cord with throw rugs, runners or
similar coverings. Arrange cord away from traffic areas to avoid tripping over the cord.
8. Turn off all controls before unplugging. Remove the plug from the outlet when not in use
for long periods of time. To avoid a tripping hazard, safely coil the cord.
9. Don’t insert or allow foreign objects to enter the inlet grill. Don’t block the opening. Keep
free of dust, lint, hair and anything that may reduce airflow as this may cause an electric
shock or fire, or damage the tower.
10. Don’t use the tower outdoors, on construction sites or on wet surfaces. The tower is not
intended for use in bathrooms, laundry areas or similar indoor locations. Never place the
tower where it may fall into a bath or other water container. Do not use or store where it
may get wet or in the immediate surroundings of a bath, a shower, or a swimming pool.
11. Don’t immerse the tower, its power cord or plug it into water or other liquids.
12. Use of extension cords aren’t recommended.
13. Don’t use in conjunction with or directly next to an air freshener or similar products.
14. Don’t use any cleaning agent or lubricants on this tower (see page - 7 -). Unplug before
cleaning, carrying and performing any maintenance.
15. Do not use on soft surfaces, such as a bed, where air inlet may become blocked.
16. When performing filter maintenance, do not force the filter to dry using alternative
methods. Doing so could damage the filter.
17. Do not use in areas where gasoline, paint or flammable liquids are used or stored.
Specifications
Model no.
A5716
Rated voltage/frequency
110-120V~/60Hz
Rated current
0.45A/10.5A
Max power
1200W
Packing meas.
34”H X 9.5”D X 9.5”D
Net weight
8.5 lbs.
Oscillation
30/60/90/120
Timer
1h~8h
- 5 -
Parts and Features
1. Control panel
2. Air outlet
3. Display panel
4. Remote control
5. Infrared receiver
6. Chassis
7. Filter
8. Air inlet grill
Operation Instructions
Control panel Remote control Display panel
1. Power button: Press power switch on the base first. Then press “ON/OFF”
button on the control panel so that fan will start to blow cool air. Press “power
button” again so that fan will stop.
2. Hot button: Press “HOT” button for 3 seconds. The fan will start to blow hot air.
Press “HOT” again and the fan will blow cool air.
1
2
3
4
5
6
7
- 6 -
3. Timer ON: Press “TIMER ON” button to set timer. The LED will display 1H-8H as
your options. The fan will turn off automatically after 1H-8H.
4. Timer OFF: Press “TIMER OFF” button; timer will be cancelled.
5.“ - ” Press “-” button to decrease airflow. The unit has 7 speed levels to choose from.
6.“ + ” Press “+” button to increase airflow. The unit has 7 speed levels to choose
from.
7．“ ” Swing: Press “SWING” button. The LED will display “12” which means the unit
will oscillate in a 120° arc. Press again to display “90” for a 90° oscillation, press
a third time to display “60” for a 60° oscillation, press a fourth time to display “30”
for a 30° oscillation. Press a fifth time to display “00” to cancel oscillation.
Just a reminder：
The BEEP when you press power means remote control and control panel are
working.
Remote Control Instruction
Replace the remote control lithium battery
1. Rotate the battery cap clockwise by hand or with a screwdriver, following the direction as
indicated by the arrows. Align the mark in the cap with the mark to remove the battery
cap.
2. Install the battery.
3. Fit the cap and rotate the battery cap counter clockwise to align the mark in the cap with
mark in the body of remote control.
Remote control Step 1 Step 2 Step 3
- 7 -
Notice for Remote Control
● To prevent children activating the heat setting, this unit cannot be powered on by
using the remote control.
● The infrared receiver is located in the bottom of LED display and top of the fan. The
remote control can also work when placed on the top of the fan. The remote control
should be pointed at the LED display when pressing any button on the remote control
to get the best signal transmission.
● When the fan is swinging sideways it is suggested to hold the remote at a 45° angle.
● Don't put any obstructions between the receiver and remote control.
Care and Cleaning
Please unplug the tower from the outlet before cleaning.
1. Cleaning the housing
Please wipe with a dry or damp cloth. Do not use detergents or polishes to clean
the tower.
2. Cleaning the air inlet
Remove the air inlet grill and filter. Please use soft brush or vacuum to clean.
We also suggest replacing the filter if it’s dirty and install a new one.
Air inlet grill can be washed with water. Completely dry before re-installing.
3. Cleaning the air outlet
Please use a soft brush to clean the debris inside the air outlet.
- 8 -
Troubleshooting Guide
Please note HEPA Filter may decrease air speed/volume. For higher CFM, a charcoal only
filter is available. Contact customer service at 1-800-225-6595 for more information.
SERVICE – For repairs or service, please visit your place of purchase, call 1-800-225-6595
or visit www.edenpuresupport.com.
WARNING
ANY REQUIRED SERVICE OTHER THAN FILTER MAINTENANCE SHOULD ONLY BE
PERFORMED BY AN AUTHORIZED SERVICE REPRESENTATIVE.
Problem
Possible cause
Suggested solution
Power indicator light does
not turn on
No power to the fan
1. Check to see if outlet is
working
2. Consult with an electrician
3. Ensure the fan is on a level
surface
4. Check the power switch to
ensure it is on
Airflow is slow
The voltage is too low
Air inlet or outlet is
blocked
1. Don’t restart until the voltage
is back to normal
2. Clean the air inlet or outlet
©2017 EdenPURE® I-5434 BR11626R-1
/
