READ AND SAVE THESE INSTRUCTIONS
INSTRUCTIONS FOR MOUNTING LIGHT FIXTURES
K2HB (
INCANDESCENT)
or K1HC (
HALOGEN)
WARNING: To reduce the possibility of electrical shock, be sure that the power is turned off at its source
(fuse or circuit breaker)
. All electrical components must be installed in accordance with national and local
electrical codes. To reduce the risk of fire and electrical shock, use this light fixture only with UL Listed
Casablanca ceiling fans indicated as adaptable on the chart included with these instructions.
continued . . .
INSTALLATION
SWITCH
HOUSING
CAP
8-32 SCREW
FIG. 2
WIRE NUT
PLASTIC PLUG
BLUE WIRE
KNURL NUT
PULL-CHAIN
SWITCH
FIG. 1
WHITE WIRE
FIG. 3
5 BEADS
PULL CHAIN
w/NYLON TUBING
1. Remove the cap from fan by removing two brass 8-32
screws and save these screws for attaching light fixture. This
cap will not be reused. Remove plastic wire nuts from switch
housing wires and strip 1/2" insulation from both wires (black
or blue, and white). See FIG. 1
NOTE: For K2HB (
incandescent)
Light Fixture: If install-
ing this light fixture on a 3 Speed pull-chain model fan, a
separate pull-chain switch (included with the fan) must
be installed. Refer to the following installation instruc-
tions. Otherwise, for K1HC (
halogen)
Light Fixture instal-
lation skip to step 5.
2. Remove the plastic plug from the fan switch housing.
Install the light on-off switch by inserting the chain through
hole, from the inside. Pass the switch threads into the hole
and screw the knurl nut onto the switch. Hand tighten firmly.
See FIG. 2
3. Attach the blue wire from the fan (labeled D1-OPTION) to
one of the blue wires on the switch by twisting the bare ends
of the wires together. Secure the splice by threading on one
of the wire nuts provided. Test the secureness of the splice
by pulling on the wire nut. Check that there is no bare wire
showing from the wire nut then cover connection with electri-
cal tape.
4. Count 5 beads away from the pull chain switch and cut the
pull chain. Attach the beaded pull chain with nylon tubing to
the switch. Repeat installation of the beaded pull chain with
nylon tubing for the fan speed switch already attached to the
switch housing. See FIG. 3
CAUTION: Use only incandescent
light bulbs with K2HB light fixture
and only halogen light bulb with
K1HC light fixture.
BEFORE YOU START:
• THE K1HC LIGHT FIXTURE (HALOGEN) NOT FOR USE ON 3 SPEED
PULL-CHAIN MODEL FANS. (MODEL NUMBERS ENDING WITH "D")
• Light fixture to fan compatibility chart located on last page of instructions.
• This switch housing may or may not have electronics in it.
• K2HB and K1HC for use with G101, G102, G103, and G104 Glass Shades (sold separately).
5. Thread the two 8-32 screws half way into the two threaded
holes on the switch housing. See FIG. 4
6. While holding light fixture up to the fan, attach the wires
from the fan switch housing and the wires from the light fixture
together (black-to-black or blue-to-black and white-to-white)
by twisting the bare ends of the wires together. Then secure
the splices by threading on the porcelain wire nuts provided.
Test the secureness of each splice by pulling on the wire nut.
Check that there is no bare wire showing from the wire nut
then cover both connections with electrical tape.
7. Align the two 8-32 screws on the switch housing with the
two key slots on the housing cover. Rotate light fixture
clockwise, make certain screw heads have rotated to the
narrow end of the slot.
CAUTION: Make sure no wires are pinched between light
fixture and switch housing. Tighten the screws to secure
light fixture.
8. Install the light bulbs. Do not exceed the maximum
wattage indicated on the light fixture.
CAUTION: Make certain to remove dust and oil from the
halogen light bulbs after installation. Failure to do so will
shorten bulb life.
9. Align the four (4) indents in the glass with the four (4) spring
tabs in the shade holder and turn in either direction 1/8 turn
(2"). Make certain spring tabs lock onto glass. See FIG. 5
(Skip step 10 if this light fixture is not intended for
mounting to a 3 speed pull-chain fan)
10. For 3 speed fan series. Connect the fob pull chain.
Repeat for both switches. See FIG. 6
FIG. 4
FIG. 6
SWITCH
HOUSING
8-32 SCREW
PORCELAIN
WIRE NUT
KEY SLOT
LIGHT
FIXTURE
LIGHT BULB
GLASS
(NOT INCLUDED)
FOB PULL
CHAIN
CAUTION: Make sure no wires are pinched
between light fixture and switch housing.
INSTALLATION
FIG. 5
INDENT
(GLASS)
SPRING TAB
(SHADE-
HOLDER)
P/N 1943930 REV.B P/D JUN96PDG 8A265
MM
MM
M
ODELODEL
ODELODEL
ODEL
SS
SS
S
ERIESERIES
ERIESERIES
ERIES
K1K1
K1K1
K1
K2K2
K2K2
K2
K4K4
K4K4
K4
K4BK4B
K4BK4B
K4B
K4CK4C
K4CK4C
K4C
K4SK4S
K4SK4S
K4S
K4ZK4Z
K4ZK4Z
K4Z
K5LK5L
K5LK5L
K5L
K2HBK2HB
K2HBK2HB
K2HB
K1HCK1HC
K1HCK1HC
K1HC
KG1JKG1J
KG1JKG1J
KG1J
KG1PKG1P
KG1PKG1P
KG1P
KG1QKG1Q
KG1QKG1Q
KG1Q
KG1Q-RKG1Q-R
KG1Q-RKG1Q-R
KG1Q-R
KG1RKG1R
KG1RKG1R
KG1R
KG1SKG1S
KG1SKG1S
KG1S
KG1TKG1T
KG1TKG1T
KG1T
KG1UKG1U
KG1UKG1U
KG1U
KG2FKG2F
KG2FKG2F
KG2F
K104K104
K104K104
K104
K134K134
K134K134
K134
K164K164
K164K164
K164
KG210KG210
KG210KG210
KG210
KG240KG240
KG240KG240
KG240
KG400KG400
KG400KG400
KG400
K4KK4K
K4KK4K
K4K
KG1XKG1X
KG1XKG1X
KG1X
KWMKWM
KWMKWM
KWM
LL
LL
L
IGHTIGHT
IGHTIGHT
IGHT
FF
FF
F
IXTURESIXTURES
IXTURESIXTURES
IXTURES
Artisan 3700TArtisan 3700T
Artisan 3700TArtisan 3700T
Artisan 3700T
Avalon 2800DAvalon 2800D
Avalon 2800DAvalon 2800D
Avalon 2800D
Clairemont 5100DClairemont 5100D
Clairemont 5100DClairemont 5100D
Clairemont 5100D
Commodore 3000DCommodore 3000D
Commodore 3000DCommodore 3000D
Commodore 3000D
Delta II 14000DDelta II 14000D
Delta II 14000DDelta II 14000D
Delta II 14000D
Four Seasons 7300DFour Seasons 7300D
Four Seasons 7300DFour Seasons 7300D
Four Seasons 7300D
Four Seasons 7500DFour Seasons 7500D
Four Seasons 7500DFour Seasons 7500D
Four Seasons 7500D
Four Seasons 7600DFour Seasons 7600D
Four Seasons 7600DFour Seasons 7600D
Four Seasons 7600D
Genesis 900DGenesis 900D
Genesis 900DGenesis 900D
Genesis 900D
Hermosa 3900DHermosa 3900D
Hermosa 3900DHermosa 3900D
Hermosa 3900D
Hermosa 3900THermosa 3900T
Hermosa 3900THermosa 3900T
Hermosa 3900T
Hugger 7100DHugger 7100D
Hugger 7100DHugger 7100D
Hugger 7100D
Hugger 7200DHugger 7200D
Hugger 7200DHugger 7200D
Hugger 7200D
Lady Delta 16000DLady Delta 16000D
Lady Delta 16000DLady Delta 16000D
Lady Delta 16000D
New Orleans 8000DNew Orleans 8000D
New Orleans 8000DNew Orleans 8000D
New Orleans 8000D
Outsider 8100DOutsider 8100D
Outsider 8100DOutsider 8100D
Outsider 8100D
Palisades 42000DPalisades 42000D
Palisades 42000DPalisades 42000D
Palisades 42000D
Palisades 42000VPalisades 42000V
Palisades 42000VPalisades 42000V
Palisades 42000V
Panama 12000TPanama 12000T
Panama 12000TPanama 12000T
Panama 12000T
Panama 12000RPanama 12000R
Panama 12000RPanama 12000R
Panama 12000R
San Marino 3100TSan Marino 3100T
San Marino 3100TSan Marino 3100T
San Marino 3100T
Ventura 27000TVentura 27000T
Ventura 27000TVentura 27000T
Ventura 27000T
Victorian 2000DVictorian 2000D
Victorian 2000DVictorian 2000D
Victorian 2000D
Victorian 2000TVictorian 2000T
Victorian 2000TVictorian 2000T
Victorian 2000T
FAN CONTROL: R=COMFORT•TOUCH V=VERSA•TOUCH T=INTELI•TOUCH D=PULL CHAIN
LIGHT FIXTURE TO FAN COMPATIBILITY CHART
/
