Casablanca K1HC Instructions for Mounting

Brand: Casablanca

Model: K1HC

Type: Instructions for Mounting

This manual is also suitable for

K2HB

READ AND SAVE THESE INSTRUCTIONS

INSTRUCTIONS FOR MOUNTING LIGHT FIXTURES

K2HB (

INCANDESCENT)

or K1HC (

HALOGEN)

WARNING: To reduce the possibility of electrical shock, be sure that the power is turned off at its source

(fuse or circuit breaker)

. All electrical components must be installed in accordance with national and local

electrical codes. To reduce the risk of fire and electrical shock, use this light fixture only with UL Listed

Casablanca ceiling fans indicated as adaptable on the chart included with these instructions.

continued . . .

INSTALLATION

SWITCH

HOUSING

CAP

8-32 SCREW

FIG. 2

WIRE NUT

PLASTIC PLUG

BLUE WIRE

KNURL NUT

PULL-CHAIN

SWITCH

FIG. 1

WHITE WIRE

FIG. 3

5 BEADS

PULL CHAIN

w/NYLON TUBING

1. Remove the cap from fan by removing two brass 8-32

screws and save these screws for attaching light fixture. This

cap will not be reused. Remove plastic wire nuts from switch

housing wires and strip 1/2" insulation from both wires (black

or blue, and white). See FIG. 1

NOTE: For K2HB (

incandescent)

Light Fixture: If install-

ing this light fixture on a 3 Speed pull-chain model fan, a

separate pull-chain switch (included with the fan) must

be installed. Refer to the following installation instruc-

tions. Otherwise, for K1HC (

halogen)

Light Fixture instal-

lation skip to step 5.

2. Remove the plastic plug from the fan switch housing.

Install the light on-off switch by inserting the chain through

hole, from the inside. Pass the switch threads into the hole

and screw the knurl nut onto the switch. Hand tighten firmly.

See FIG. 2

3. Attach the blue wire from the fan (labeled D1-OPTION) to

one of the blue wires on the switch by twisting the bare ends

of the wires together. Secure the splice by threading on one

of the wire nuts provided. Test the secureness of the splice

by pulling on the wire nut. Check that there is no bare wire

showing from the wire nut then cover connection with electri-

cal tape.

4. Count 5 beads away from the pull chain switch and cut the

pull chain. Attach the beaded pull chain with nylon tubing to

the switch. Repeat installation of the beaded pull chain with

nylon tubing for the fan speed switch already attached to the

switch housing. See FIG. 3

CAUTION: Use only incandescent

light bulbs with K2HB light fixture

and only halogen light bulb with

K1HC light fixture.

BEFORE YOU START:

• THE K1HC LIGHT FIXTURE (HALOGEN) NOT FOR USE ON 3 SPEED

PULL-CHAIN MODEL FANS. (MODEL NUMBERS ENDING WITH "D")

• Light fixture to fan compatibility chart located on last page of instructions.

• This switch housing may or may not have electronics in it.

• K2HB and K1HC for use with G101, G102, G103, and G104 Glass Shades (sold separately).

5. Thread the two 8-32 screws half way into the two threaded

holes on the switch housing. See FIG. 4

6. While holding light fixture up to the fan, attach the wires

from the fan switch housing and the wires from the light fixture

together (black-to-black or blue-to-black and white-to-white)

by twisting the bare ends of the wires together. Then secure

the splices by threading on the porcelain wire nuts provided.

Test the secureness of each splice by pulling on the wire nut.

Check that there is no bare wire showing from the wire nut

then cover both connections with electrical tape.

7. Align the two 8-32 screws on the switch housing with the

two key slots on the housing cover. Rotate light fixture

clockwise, make certain screw heads have rotated to the

narrow end of the slot.

CAUTION: Make sure no wires are pinched between light

fixture and switch housing. Tighten the screws to secure

light fixture.

8. Install the light bulbs. Do not exceed the maximum

wattage indicated on the light fixture.

CAUTION: Make certain to remove dust and oil from the

halogen light bulbs after installation. Failure to do so will

shorten bulb life.

9. Align the four (4) indents in the glass with the four (4) spring

tabs in the shade holder and turn in either direction 1/8 turn

(2"). Make certain spring tabs lock onto glass. See FIG. 5

(Skip step 10 if this light fixture is not intended for

mounting to a 3 speed pull-chain fan)

10. For 3 speed fan series. Connect the fob pull chain.

Repeat for both switches. See FIG. 6

FIG. 4

FIG. 6

SWITCH

HOUSING

8-32 SCREW

PORCELAIN

WIRE NUT

KEY SLOT

LIGHT

FIXTURE

LIGHT BULB

GLASS

(NOT INCLUDED)

FOB PULL

CHAIN

CAUTION: Make sure no wires are pinched

between light fixture and switch housing.

INSTALLATION

FIG. 5

INDENT

(GLASS)

SPRING TAB

(SHADE-

HOLDER)

P/N 1943930 REV.B P/D JUN96PDG 8A265

ODELODEL

ODEL

ERIESERIES

ERIES

K1K1

K2K2

K4K4

K4BK4B

K4B

K4CK4C

K4C

K4SK4S

K4S

K4ZK4Z

K4Z

K5LK5L

K5L

K2HBK2HB

K2HB

K1HCK1HC

K1HC

KG1JKG1J

KG1J

KG1PKG1P

KG1P

KG1QKG1Q

KG1Q

KG1Q-RKG1Q-R

KG1Q-R

KG1RKG1R

KG1R

KG1SKG1S

KG1S

KG1TKG1T

KG1T

KG1UKG1U

KG1U

KG2FKG2F

KG2F

K104K104

K104

K134K134

K134

K164K164

K164

KG210KG210

KG210

KG240KG240

KG240

KG400KG400

KG400

K4KK4K

K4K

KG1XKG1X

KG1X

KWMKWM

KWM

IGHTIGHT

IGHT

IXTURESIXTURES

IXTURES

Artisan 3700TArtisan 3700T

Artisan 3700T

Avalon 2800DAvalon 2800D

Avalon 2800D

Clairemont 5100DClairemont 5100D

Clairemont 5100D

Commodore 3000DCommodore 3000D

Commodore 3000D

Delta II 14000DDelta II 14000D

Delta II 14000D

Four Seasons 7300DFour Seasons 7300D

Four Seasons 7300D

Four Seasons 7500DFour Seasons 7500D

Four Seasons 7500D

Four Seasons 7600DFour Seasons 7600D

Four Seasons 7600D

Genesis 900DGenesis 900D

Genesis 900D

Hermosa 3900DHermosa 3900D

Hermosa 3900D

Hermosa 3900THermosa 3900T

Hermosa 3900T

Hugger 7100DHugger 7100D

Hugger 7100D

Hugger 7200DHugger 7200D

Hugger 7200D

Lady Delta 16000DLady Delta 16000D

Lady Delta 16000D

New Orleans 8000DNew Orleans 8000D

New Orleans 8000D

Outsider 8100DOutsider 8100D

Outsider 8100D

Palisades 42000DPalisades 42000D

Palisades 42000D

Palisades 42000VPalisades 42000V

Palisades 42000V

Panama 12000TPanama 12000T

Panama 12000T

Panama 12000RPanama 12000R

Panama 12000R

San Marino 3100TSan Marino 3100T

San Marino 3100T

Ventura 27000TVentura 27000T

Ventura 27000T

Victorian 2000DVictorian 2000D

Victorian 2000D

Victorian 2000TVictorian 2000T

Victorian 2000T

FAN CONTROL: R=COMFORT•TOUCH V=VERSA•TOUCH T=INTELI•TOUCH D=PULL CHAIN

LIGHT FIXTURE TO FAN COMPATIBILITY CHART

Casablanca K1HC Instructions for Mounting

Brand: Casablanca

Model: K1HC

Type: Instructions for Mounting

This manual is also suitable for

K2HB

Download PDF

report

Casablanca K1HC Instructions for Mounting

This manual is also suitable for

Casablanca K1HC Instructions for Mounting

Related papers

Other documents