Haier HW85-B1486NZP Operating instructions

Brand: Haier

Model: HW85-B1486NZP

Category: Washing machines

Type: Operating instructions

Haier Automatic Drum Washer

Operating Instructions

Models:

Please read these instructions carefully before use.

Please save these instructions for future reference.

Specifications

53dB (A weighted)

71dB (A weighted)

Grade 1

1,400 rpm

Power supply

Water inlet pressure

Rated washing capacity

Rated spinning capacity

Spinning speed

Washing noise

Spinning noise

Energy efficiency rating

Dimensions (H×D×W)

 Applicable standard: GB/T 4288-2008 Household and Similar Electrical

Washing Machine.

 The diagrams in this manual are for illustrative purpose only. Due to

continuous product improvement, please see the actual product for the

appearance, color and accessories which may be inconsistent with those

described in this manual. Here we apologize for this.

 This product is classified as Class I appliance. Please pay attention to

electrical safety during use.

Certificate of Quality

Inspector:

Haier Group

Qingdao Haier Drum Washer Co., Ltd.

Address: Haier Industrial Park, Qingdao Hi-tech

Industrial Development Zone

Tel: 4006 999 999

Fax: 0532-87636565

Postal code: 266101

Website: www.haier.com

Customer service e-mail: [email protected]

Headquarters address: No. 609, 308 National

Highway, Qingdao

Version: 1st version, 2009

Special No.: 0020505574A

V98497

Contents

1. Notice before Use

2. Safety Precautions

3. Precautions for Use

4. Preparations before

Washing

5. Operational Procedure

6. Control Panel and

Program Description

7. Display Screen

Description

8. Other Functions

9. Fault Clearance

10. Cleaning/Maintenance

 Technology of automatic closedown upon

clean detected

 Real-time door open

 Automation technology

 Crease-resistant and soak function

 Technology of anti-bacteria and

mildew-proof with window pad

 Self-cleaning function

 Foam self-checking function

 Power-off memory function

 Technology of variable frequency drive

 When selecting the pre-wash function or the

pre-wash program, add detergent into the

pre-washing chamber to pre-wash the clothes;

 As for the dosage of detergent, please refer to the

instructions for detergent. Excessive detergent

may result in too many bubbles and spill as well

as affect its dissolution. Special low foaming

detergent for drum washers shall be used. When

washing synthetic or wool fabrics, be sure to use

special detergent;

 Do not allow the level of softener or liquid

detergent to exceed the “MAX” mark of distributor

box. Concentrated softener or liquid detergent

should be diluted before being added into

distributor box. Excessive softener may damage

the synthetic fiber. As for the dosage of softener,

please refer to its instructions.

 Check the clothes for special washing

requirements and make sure that the clothes

are suitable for washing with washing machine

and water in order to avoid the deformation

and damage of the clothes.

 For the clothes tainted with much

mud and dust, please remove

them before washing.

 Wash those clothes liable to color fading

separately from other clothes.

 Tie the ties, buckle the buttons, zip the

zippers and sew the openings.

 To avoid the sound from

buttons, please turn those

clothes with buttons inside out

before putting them into the

washer.

 Please unfold and fluff out the clothes before

putting them into the washer. Furthermore,

do not overload the washer.

 When washing small articles (e.g.

handkerchief, gloves, socks, etc.) and those

clothes liable to intertwist and wear, please

put them into net bags for washing, rinsing

and spinning to prevent them from falling into

between the inner drum and window pad and

further avoid incomplete washing or damage

to top-grade clothes. The weight of articles in

each net bag should not exceed 300g and

the net bags should not be washed together

with those clothes not in a net bag, otherwise

the washer will not be balanced, resulting in

abnormal vibration.

Reference weights for small articles:

handkerchief: about 30g/piece; gloves:

about 60g/pair; cotton socks: about

30g/pair; silk socks: about 20g/pair.

 Check pockets and remove

coins, sand, hairpin and other

things from them.

 According to the max washing capacity specified in

A.4 of

Appendix A to the standard GB/T4288-2008.

 For energy efficiency test program, please select “cotton +

60°C + strong wash + max washing capacity + max speed”.

1. The plug should be accessible after the washer is

installed in place. Do not disconnect the plug

from the socket by pulling the power cord. If the

power cord needs to be replaced, ask a qualified

person or contact our After-sales Service

Department for replacement. Prevent the power

cord from being pressed by any foot and from

such problems as break-o

ff, flattening, etc.

2. Power supply must use an independent socket,

the grounding terminal of which must be properly

grounded. The socket must be a qualified product

with the following 3C certification mark:

3. Such overload protective devices as suitable fuse must be available

at the user’s home. And, the ammeter, wire and socket must be able

to withstand 10A current.

1. Keep the washer away from any heat source and direct sunlight to prevent

the aging of plastic and rubber parts.

2. The washer’s door is relatively hot during heating. For the purpose of safety,

keep the children away from the washer. In addition, when draining hot water,

be careful to avoid scald.

3. After unpacking the washer, do not allow the children to play with the

disassembled packaging materials such as carton, plastic packaging bag and

foam, etc.

4. Do not install the washer outdoors and in excessively humid environment,

otherwise moisture on the electrical components may easily cause damage to

the ignition system or other accidents. In case of inadvertent water spray onto

or into the washer, only after the washer is thoroughly dried can you use it.

5. Neither place the washer directly onto the airproof carpet nor close up to the

wall or furniture to avoid accidents.

The carpet must not block the bottom vent.

Do not use the washer on any platform higher than the floor, otherwise it may

fall off onto the floor and be damaged.

1. Do not use such chemicals as flammable detergent and

dry-cleaning solvent to wash the clothes. Do not use any

organic solvent or corrosive liquid to wipe the exterior and

rubber parts of the washer. Do not use any flammable spray

1. Due to the fluctuation of water pressure, please check all the joints of water inlet

pipe, water tap and drain pipe for firm connection before washing every time. In

case of loose water pipe connection or water leakage, please turn off the water

tap and take proper measures or contact our

After-sales Service Department for

reconnection. Only after such faults are cleared can you use it again.

2. When the washer is not in use, please keep the door slightly open to avoid

unpleasant smell. Do not cover the washer with a plastic bag to avoid moisture

staying in the washer.

3. Do not place any heavy object, heat-producing appliance and item liable to

water/liquid leakage to avoid the deformation of table top and plastic parts.

4. Do not wash such waterproof articles as raincoat, bicycle cover and down

products as well as carpet to avoid abnormal vibration or the damage to articles.

5. Do not open any detergent distributor box during the program operation to avoid

some detergent leaving in the box.

6. If a brassiere with steel wire is washed in the washer, the steel wire may bounce

out. Therefore, do not wash any brassiere with steel wire in order to protect the

washer.

7. The washer ’s door is equipped with self-lock safety device. Only when the

washer is in safe state (the water level is below the lower edge of sight glass,

the temperature inside of the drum is 50°C, the inner drum is not rotating) can

you unlock the door. Never forcibly open the door before the washer reaches

the safe state to avoid damage to the door or scald. “Click” will be heard when

opening the door. It is normal and arises from the working principle of

electromagnetic lock’s internal structure.

8. Turn off the water supply and power supply after finishing washing every time.

Moreover, clean the sight glass window pad interlining to prevent contaminants

from tainting the clothes again.

9. It is recommended that the washer be installed in a location with floor drainer.

10. Using the washer in the environment with the temperature at 0°C or below 0°C

may damage the water inlet valve and drainage system. If the washer is stored

in the environment with the temperature at 0°C or below 0°C, be sure to move

and leave it in the environment at room temperature for 2-4 hours before use.

11. Do not put the clothes tainted with chemicals into the washer.

12. Washing, drying capacity

near the washer. In case of flammable gas leakage, do not plug or unplug the

washer’s power plug. Do not use the washer near the environment with

flammable and explosive gas & liquid such as biomass pool, etc.

1. Notice before Use

2. Safety Precautions

5. Operational Procedure

3. Precautions

for Use

4. Preparations

before Washing

Please install and adjust the washer

according to the instructions in this manual

so that you can use it in a safer manner.

To connect the water inlet pipe

1. Select a proper water tap

Distributor boxes

2. Remove the water inlet pipe joint

The length of front end must be more than 10mm. In

case of unsmooth end face of the water tap outlet,

please file it smooth to avoid water leakage.

ķ Press the lower end of locking

lever;

ĸ Hold the water inlet pipe, press

down the slider and remove

the water inlet pipe joint;

Ĺ Remove the nameplate.

4. Connect the water inlet pipe

5. Connect to the washer

6. Check the water inlet pipe for

good connection

To paste the felt and install

the Noise Reduction Board

Drain pipe

To adjust

the feet

Accessories

ķ Press down the slider and insert the water

pipe into the water inlet pipe joint;

ĸ Hook the water inlet pipe joint with the

locking lever, then loosen the slider until a

“poop” is heard.

ķ Ring the nut at the other end of water inlet

pipe onto the water inlet valve joint;

ĸ Tighten and confirm the nut of water inlet

pipe in place.

ķ Check for firm connection;

ĸ After installation, turn on the water tap and

check for water leakage;

Ĺ Before every use of washer, please check

for good connection between the water inlet

pipe and the water tap;

ĺ Never forcibly bend the water inlet pipe.

1. Paste the felt on one side of the Noise

Reduction Board.

2. Incline the washer backwards and remove the

four feet (Fig. 1);

3. Place the side with felt of splash plate

inwards, install the foot bolts through the four

holes on the shell and tighten them (Fig. 2),

then level the washer.

The outlet end of drain pipe must be

higher than 80cm and the highest point

must be less than 100cm. To prevent the

drain pipe from coming off, you may

secure it to its clamp at the back of

washer or to the firm support as shown

in the figure.

It is not recommended to extend the

drain pipe. If the extended pipe exceeds

2.5m in length, water feeding and

drainage may easily occur at the same

time. Please contact our After-sales

Service Department for extending the

drain pipe.

(Add a proper amount of

detergent required by washing)

Pre-washing detergent box

Washing detergent box

Softener and bleacher bo

Be sure to

adjust the

four feet to

level the

washer

before use.

Water inlet pipe assy

Noise Reduction

Board

Drain pipe support

Operating

Instructions

Warm Tips Card

Felt

After finishing the adjustment of

the four feet, turn the foot

support nut to cling to the shell

in order to support the washer.

Note

3. Install the water inlet

pipe joint

ķ Loosen the nut to the extent that approximate

3-4 turns of screw thread are exposed;

ĸ Loosen four screws of the water inlet pipe

joint to the extent that the joint can be ringed

onto the water tap;

Ĺ If the water inlet pipe joint cannot be ringed

onto the water tap, please remove the

bushing and install again;

ĺ Turn one of screws to an approximately

proper position in advance, ring the water

inlet pipe joint onto the water tap, then evenly

tighten the remaining three screws in place,

and finally tighten the nut.

Water inlet

pipe joint

Locking

lever

Locking

lever

Slider

Water inlet pipe

Wall

If the water tap is

placed against the

wall, you may turn

this screw to a proper

position in advance.

Bushing

3-4 turns

Nameplate

Nut

Fig. 1 Fig. 2

Table top

Drain pipe

support

Main control

panel

front board

Inner dru

Window pa

Type of clothes

Fadeless cotton fabric

Terylen

fabric/blend

fabric/chemical

fiber fabric

Wool fabric

2kg 2kg

8.5kg

4kg

HW85-B1486NZP

Silk fabric

Door

Sight glass

Bottom trim

Filter door

Foot

Electrical safety

prompt: Please pay

attention to electrical

safety when using

the washer.

Warning sign: The

contents with this

sign involve the

safety of both the

product and user. Be

sure to strictly follow

these instructions,

otherwise the

washer may be

damaged or the user

may be injured.

Prohibitory sign: The

contents with this

sign indicate the

behaviors to be

absolutely

prohibited. Failure to

follow these

instructions may

result in damage to

the washer or

personal injury.

Connect the

water inlet

pipe, turn on

the water tap

Place the

drain pipe

Insert the power

plug into the

power socket

Turn on

the power

switch

Select the

desired program

Select washing time, times of rinsing,

spinning speed, strong wash, pre-wash ,

etc. as required.

“Delay” program is off by default.

To activate this program, press

“Delay” button to make settings.

Start the

selected

program.

(Refer to “Distributor Boxes” in “Notice before

Use” section for details.)

Open the doo

r, put the clothes into the

washer, close the door, then add a proper

amount of detergent into the distributor

box and close the distributor box.

After finishing washing, the washer will

automatically switch off.

Haier Automatic Drum Washer

Operating Instructions

Models:

Please read these instructions carefully before use.

Please save these instructions for future reference.

This product is only for sale in Mainland China.

Contents

1. Notice before Use

2. Safety Precautions

3. Precautions for Use

4. Preparations before

Washing

5. Operational Procedure

6. Control Panel and

Program Description

7. Display Screen

Description

8. Other Functions

9. Fault Clearance

10. Cleaning/Maintenance

11. Warranty Instructions

 Technology of automatic closedown upon

clean detected

 Real-time door open

 Automation technology

 Crease-resistant and soak function

 Technology of anti-bacteria and

mildew-proof with window pad

 Self-cleaning function

 Foam self-checking function

 Power-off memory function

 Technology of variable frequency drive

HW85-B1486NZP

Table top

Water inlet valve

Power cord

Screw (4 pcs)

Power plug

Back cover plate

Drain pipe clamp

Drain pipe

Splash-proof plastic

plug (4 pcs)

Shell

Packaging bolts and accessories

Packaging bolts and accessories are used to fix

internal components of the washer during transport

and should be removed before using the washe

Unscrew packaging bolts and take out

the back-up block.

Block the bolt hole with a splash-proof

plastic plug.

Please keep such disassembled components as

packaging bolt and back-up block in a safe place for

future handling of the washer.

+:%1=3

850mmX650mmX595mm

0.001

Anti-crease

Prewash

Delay

Strong

Wash

Rinse

Spin

Temp.

Speed

Auto

Start/Pause

Power

Heavy

Underwear

Sport wash

Night

Quick

Spin

Tub Clean

Wash

Rinse

Spin

Temp.

Speed

Auto

Silk

Wool

Synthetic

Memory

Cotton

Anti-crease

PrewashDelay

Strong

Start/Pause

Press and hold 2seconds

to set door unlocked

HW85-B1486NZP

8.5kg

Power

Heavy

Underwear

Sport wash

Night

Quick

Spin

Tub Clean

Wash

Rinse

Spin

Temp.

Speed

Auto

Silk

Wool

Synthetic

Memory

Cotton

Anti-crease

PrewashDelay

Strong

Start/ Pause

Press and hold 2seconds

to set door unlocked

HW85-B1486NZP

8.5kg

6. Control Panel and Program Description

• Press the “Wash”

button to set washing

time. Press and hold

this button to change

the time continuously.

Click this button up until

the end.

• This function is not

applicable to “ Spin ”

and “ Tnb cleaning ”

process

Display washing time,

remaining time, times

of rinsing, spinning

time, temperature

setting value, speed

setting value, position

of clothes weight, child

lock state, door lock

state, washing

progress and alarm

message, etc.

Press the “Spin”

button to select

spinning time.

The

maximum allowable

spinning time varies

with programs.

Press the

“Rinse” button

to select the

times of rinsing

and the

maximum

allowable times

of rinsing is 8.

• Press the “Temp.”

button to select

heating temperature

(--, 30, 40, 50, 60,

90). The maximum

allowable heating

temperature varies

with programs.

• “ˉ” in the

temperature display

indicates non-heated

washing.

Press the

“Speed” button

to select

spinning speed.

The maximum

allowable

spinning speed

varies with

programs.

Programs Guide

Cotton For washing cotton fabrics

Memory For storing user customized

washing settings

Synthetic For washing chemical fiber

fabrics

Wool For washing wool fabrics

Silk For washing silk fabrics

Heavy For sheets towels and

other fabrics washing

Underwear For cotton underwear

washing

Sport wash For washing cotton fabrics;

please use

P & G’s Lander

softener; rinse only one

time, realizing water, time

and energy saving

Night For the clothes

made of cotton, linen and

chemical fiber fabrics, and

will be quieter.

Quick For washing slightly dirty

fabrics, light clothes and

brand-new clothes

Spin For spinning the clothes

Tub clean For washing the washer’s

inner drum; please add a

small amount of washing

powder or detergent, but do

not put any clothes into the

washer

“Washing” time

“Spinning” time

“Strong ” button “Delay” button

“Pre-wash” button “Anti-crease” button

“Start/pause” button

Display screen

“Temperature” selection

“Speed” selection

“Auto” button

Program knob

• Select the

desired program

by turning this

knob.

• After turning on

the washer, it

automatically

selects the

program of last

washing.

• Press the “Power” button

to turn the power on.

Press this button again

and hold it for 2 seconds

to turn the power off.

• After turning the power

on, if any button is not

pressed within 5

minutes, the washer will

automatically shut down.

• Press “Strong ” button to increase the

washing time and times of rinsing during

the main washing stage of selected

program.

˄This feature is applicable for

dirty clothes ˅

• The illuminated icon indicates the “strong”

function is selected.

• This additional function applies to “cotton”,

“memory”, “synthetic” ,“night washing”

“heavy”and “Sport wash” programs only.

• This button is effective before starting a

program.

The icon illuminates when the “delay”

function is selected

If the “delay” function is not

selected, this icon will illuminate

when the washer is turned on

Power-down memory

With the power-down memory function, the washer can

memorize the program

’s running state in case of power failure

or loose plug during washing and continue the selected

program after resuming the power supply.

Child lock icon (simultaneously press and hold the “Delay” and “Start/pause” buttons for 3s, the child lock function will be activated to

avoid changing the selected program by inadvertent touch of buttons; simultaneously press and hold the two buttons for 3s again, this

function will be cancelled; in the child lock mode, the user needs to unlock manually after the washing program ends)

heating temperature

spinning speed

position of clothes

weight

Door lock icon (the icon illuminates when the door is closed)

Note

•The time displayed on the display screen is only for reference and may be slightly different from the actual time.

•The child lock function will be automatically removed when process ends or the plug unconnected.

main washing

time

times of rinsing

program

progress bar

remaining

spinning time

Numerical display zone (After turning the power on, the time of

last washing program is displayed in this zone; display various

preset codes, e.g. is displayed at the time of

trouble alarm)

• Press the “Delay” button and the illuminated icon indicates

that the “delay” function is selected. The delay time

(0.5-24h) increases by 30 minutes each press of “Delay”

button. The time will change continuously if you press and

hold this button until you release it.

• The delay time is the end time of washing. For example,

6:00 means the washing ends after 6 hours (the delay time

must be longer than the program’s running time).

• The “Delay” function is not available for “Spin” and

“Tub clean” programs.

•Press the “Start/pause”

button, the washer will start

and the indicator light remains

on. If this button is pressed

when the washer is in

operation, the washer will

pause and the indicator light

will flash.

•When power is on, but you do

not press "Start / Pause"

button to start the washi ng

machine, if it meets door open

condition,please press the

button for 2 seconds and the

door will be open.

• Press the “Prewash” button to select or cancel the prewash

program.

• The prewash program can be selected for washing heavily

soiled clothes.

• Press the “Prewash” button, the “Prewash” icon will illumin ate.

Press the “Prewash” again, the prewash function will be

cancelled and the “Pre-wash” icon will go out.

• When selecting the prewash function, add a proper amount of

detergent into the prewash box, otherwise do not add any

detergent into the prewash box.

• This additional function applies to “cotton”, “memory”, “synthetic”

and “Lander” programs only.

• Press "Anti-crease" button to startup/shutdown the

crease-resistant and soak function.

•When the process runs to the last rinse, the washing

machine is not going to drain, clothes will be soaked in

water, and the soak icon flashes, the remain time not

decreasing. If you need to dry the clothes, you can

press "Anti-crease" button or “start /pause”button,

then the icon will be off to cancel this function,

and the washing machine continue to work.

• This feature and the "Delay"button can not be chose at

the same time. Also this feature is only effective in the

“cotton”, “memory”, “synthetic”,“heavy” , “underwear”,

“Sport wash”, “night washing” process.

7. Display Screen

8. Other functions

9. Fault Clearance

Eccentric protection

When spinning, if the clothes are not evenly distributed, the washer will fluff

out and redistribute the clothes and continue spinning after the clothes

distribution becomes even. If the clothes distribution does not become

even within the specified time, the washer will not spin to avoid abnormal

vibration. In this case, please check the clothes for intertwist and

rearrange them, then select “spin” program to spin the clothes.

When there are few clothes, the washer may not spin due to

eccentric protection. In this case, you can put more clothes into the

washer and make them evenly distributed, then continue spinning.

In addition, it is normal that the program time will prolong for the

washer rearranges and fluffs out the clothes.

Silencing function

Select the self-clean program, simultaneously press and hold the

“Delay” and “Pre-wash” buttons for 3s to silence the beep of all the

programs (excluding the alarm sound), and the display screen will

display “BEEP OFF”.

Function

Simultaneously press and hold the “Delay” and “Pre-wash” buttons

for 3s to resume the beep of all the programs, and the display

screen will display “BEEP ON”.Note: The alarm sound in light

washing process p(not including the "Unb") can not be removed

Automatic closedown upon clean detected

Select a proper program and add a proper amount of washing

powder according to the quantity and degree of dirtiness of the

clothes to be washed, the washer can automatically adjust

washing time and times of rinsing to achieve the best washing

effect.

The following phenomena are not necessarily faults of the washer. Please check against the following table before call for servicing.

If any fault actually exists, please contact our After-sales Service Department and do not repair by yourself. Please pull out the power plug

before check.

State Phenomenon Solution State Phenomenon Solution Displayed code Code meaning Solution

erofeB

noitarepo

gnihsaw

esnir

nehW

niard

srehtO

gninnips nehW

hsaw nehW

There is a small amount of water

in the drain pipe and washer

when using for the first time

The washer does not operate

Buttons cannot be operated

Water leakage occurs at the

water tap

No water inflow or slow water

inflow

Water feeding and water

drainage occurs at the same

time

Abnormal noise

It is normal; the water is the remaining

water of factory inspection

Poor washing effect

Forceless washing

Stop operation during washing

Repeated rinsing but no spinning

No spinning

Loud noise when spinning

Vibration and displacement

The clothes are not spun dry after

finishing the spinning program

No water discharge or slow water

discharge

The control panel is partially hot

The washing does not end after

the preset delay time

•

Check whether power failure or abnormal

power supply occurs

•

Check whether the power plug is firmly

inserted into the socket

•

Check whether the fuse of power supply

or the current breaker is in good condition

•

Check whether the “power” switch is

pressed

•

Check whether the water tap is turned on

•

Check whether the “Start/pause” button

is pressed

•

Check whether the “child lock” function is

set

•

After starting, to select other programs,

please press the “Start/pause” button and

then operate

•

Check whether the shape of water tap is suitable

•

Check whether the water inlet pipe joint is

installed in place

•

Check whether the water tap is damaged

•

Check whether the highest point of drain pipe is

lower than 80cm

•

Check whether the drain pipe orifice is immersed

in the water

• Check whether the washer inclines or

shakes

• Check whether there are foreign bodies

such as coins and zippers in the washer

• Check whether the noise is from the buttons

and zippers of articles

• Check whether the noise is from the

draining pump or motor in normal operation

• The clothes distribution becomes imbalanced

during washing

• Poor water feeding/drainage conditions result

in a longer time

• It is normal that electronic components are

slightly hot

• Check whether the drain pipe is bent, clogged

or frozen

• Check whether the highest point of drain pipe

is 100cm above the floor

• Check whether the filter is clogged

• The spinning effect varies with the type of

clothes

• Check whether it is for eccentric protection

with few clothes

• Check whether all the fixing bolts for

transport are removed

• Check whether the washer is level (the feet

can be adjusted to level the washer)

• Check whether the clothes intertwist

• Check whether the washer collides with

other objects

• Check whether there are foreign bodies in

the washer

• The washer’s program is set with water

discharge time and the spinning starts after

a period of time

• Check whether the clothes intertwist

• The washer with the function of automatic

closedown upon clean detected

automatically increase or decrease the

times of rinsing (1-2 times) according to the

degree of dirtiness of the clothes

• Check whether sudden power failure or

power supply cut-off occurs

• Check whether the “Start/pause” button is

pressed

• Check whether the clothes weight exceeds

the washer’s standard washing capacity

• Check whether the type and dosage of

detergent are suitable

• Check whether the selected program is

correct

Code for the clothes quantity; L-1

is displayed when there is less

than 1kg of clothes or no clothes

in the washer

Code for the clothes quantity; L-3

is displayed when there is about

3kg of clothes in the washer

Code for the clothes quantity; L-R

is displayed when the inner drum

is basically full

The whole program ends

Abnormal door locking or

unclosed door

Drainage fault

Temperature sensor faul

Heating fault

Abnormal water inflow

Close the door; if the problem

remains, please ask for repair

Clean the draining pump filter and

check whether the drain pipe is

clogged; if the problem remains,

please ask for repair

Please ask for repai

Shut down and remove the problem; if

the problem remains, please ask for

repair

The motor speed is higher or lower than

the pre-set speed

The motor stops running

The water level exceeds alarm level

Water level sensor fault

Shut down and remove the problem; if

the problem remains, please ask for

repair

Check whether the water tap is turned on,

whether the water pressure is too low,

whether power supply cut-off occurs; if the

problem remains, please ask for repair

• Check whether the water tap is turned on and

whether water supply cut-off occurs

• Check whether the water inlet valve is clogged

(if necessary, clean the valve)

• Check whether the water tap and water inlet

pipe are frozen

• Check whether the “delay” program is selected

• Check whether the “Start/pause” button is

pressed

• Check whether the water inlet pipe is bent

• Check whether the water pressure is too low

Take out and fluff out the clothes; if the

problem remains, please ask for repair

Uneven clothes distribution when

spinning

The clothes quantity is beyond the

acceptable range

Communication fault

Being inconsistent with the conditions for

door opening, it is not allowed to unlock

the door

Take out some clothes

Please ask for repair

Pull wire

Water inlet

valve joint

Notes

 To add clothes during washing or want to

remove clothes due to extended power failure,

make sure that the water level in the drum is

properly below the lower edge of sight glass,

the water temperature is below 50

° C and the

inner drum is not running, then remove the

drain pipe from its support and lower it until no

water is drained from the drain pipe, replace

the drain pipe. Open the filter door at the

bottom of the washer, and you will see a pull

wire. Take out the pull wire and gently pull it

downwards until you hear a low sound, the

door will open, now you can add or remove the

clothes. Afterwards, reset the pull wire and filter

door.

 Frequently wash the water inlet pipe joint and

the filter screen of water inlet valve to prevent

them from being clogged by impurities.

 This washer contains recoverable materials. Please properly dispose of them to

protect the environment.

Never perform the above operations when the washer is running.

Warm tips

10. Cleaning/Maintenance

Fig. 1

Filter

Waste pipe

Water container

Waste pipe plug

Fig. 2

Fig. 3

Fig. 6

Fig. 4 Fig. 5

Please unplug the power plug from the socket before

cleaning and maintenance.

To clean the filter (once a month as recommended)

(1) After draining the water in the washer, press down the filter door

using a flat head screwdriver or a similar tool through the square

hole above the filter door (as shown in Fig. 1).

(2) Hold the plastic pipe plug to pull out the waste pipe, prepare a

water container, remove the plastic plug of waste pipe to drain the

remaining water into the container (as shown in Fig. 2), replace

the plastic plug onto the waste pipe, and finally clamp the waste

pipe in original position.

(3) Anticlockwise screw out the filter. It is normal that a little water

flows out at this time (as shown in Fig. 3).

(4)

Rinse with clean water (as shown in Fig. 4).

(5) Insert the filter after aligning the convex of filter with the groove of

draining pipe, then clockwise tighten it (as shown in Fig. 5), and

finally close the filter door.

Notes

 After finishing washing, please turn off the water tap and remove the water

inlet pipe

 Unplug the power plug and put the drain pipe in place

 If the washer is not to be used for a long time, please keep the door slightly

open and dry the window pad to avoid unpleasant smell

 Do not use organic solvent or corrosive liquid on the washer’s exterior and

rubber parts

To clean a distributor box, pull it out,

gently press it down and continue to

pull it out (as shown in Fig. 6),

remove it, rinse it with water and

reinstall it in place.

The filter must be tightened to

avoid water leakage.

The machine has automatic weighing function. Press the "Power" button to get the power on, then the door will automatically pop

open, so put clothes in, close the door, and the display screen will be ready. Press the "Start / Pause" button, about 2 minutes later

weighing will be finished and the machine will automatically calculate the best washing process. This can save a lot of water. If you

don’t need the automatic weighing, you can press “AUTO shift” button to switch to the gear of

manually selecting the amount of

clothing (screen display shows L-1 - L-A). When gear is set up, the washing machine will adjust the water, heating and washing

time and so on in accordance with the set gears to save water, time and power.

(1) D "L-1"-"L-A" correspond to the amount of clothing in barrel of 1-7, in the manual selection, when the barrel has a lot of

clothes (more than one half), please select "L-6 " or "L-A". if the barrel of clothing is relatively few (less than one half),

please select one in "L-1", L-2", "L-3", "L-4" and " L-5"

(2) Please adjust the dosage of washing powder in accordance with the gears show on screen.

Cancel or re-select process during the washing

(1) Shutdown the machine to cancel the running

process;and then boot it to re-select the procedure.

(2) If you need to select additional function when the

process is running, press "Start / Pause" button, then

select the additional function you want, at last re-press

the "Start / Pause" button to continue the running.

The above operation should be under the

status of child lock non-started.

This function is not available in the following programs or situations:

(1)

The

programs except

“cotton” and “synthetic”

program 

(2) The program where the total time of washing and heating is

less than 20min;

(3) Change main washing time or times of rinsing;

Memory program

Select the “memory” program and set various washing parameters,

all the washing settings will be stored after the washing program

ends. When the user want to wash with the same settings, just

select the “memory” program after turning on the washer. (This

program does not memorize the set “delay” and “

Anti-crease

” functions.)

Musical alert tone for washing over

The washing machine is equipped with a musical alert tone

to prompt you the washing over when the whole washing

process has ended. While enjoying the music, you can

open the machine door to take out the clothing (Non-music

style washing in night).

 Separate the color-faded clothes from the others when washing a bunch of

clothes.

 The weight of washing clothes should not exceed the maximum capacity of the

washing machine.

 Specific dirty laundry should be pre-washed first, and then put them together with

others to wash.

 For those not too dirty clothes, it may be appropriate to reduce the dosage of

detergent and choose the choice of faster washing procedure.

 Add fabric softener to make clothes soft and easy for ironing, also to remove

electrostatic bonding.

 Choose the right temperature: It is recommended to select the above 60 ° C heating

temperature for dirty clothes washing but not for the others .

 Appropriate use of detergents,excessive use will reduce the rinse effect .

 The washing machine is made of some recyclable materials, please correctly

handle with the waste when discard it and to protect the environment.

Note

Notes

displayedˈthe machine is draining at the same timeˈ

it ‘s normal.

Haier HW85-B1486NZP Operating instructions

Brand: Haier

Model: HW85-B1486NZP

Category: Washing machines

Type: Operating instructions

Download PDF

report

Haier HW85-B1486NZP Operating instructions

Haier HW85-B1486NZP Operating instructions

Related papers

Other documents