Haier HW55-B12866NZP User manual

Brand: Haier

Model: HW55-B12866NZP

Category: Washing machines

Type: User manual

Auto

Strong E xtra Rinse

D elay

Star t /

S-D Inverter

Close the door; if the problem

remains, please ask for repair

Please ask for repair

Take out and fluff out the

clothes; if the problem

remains, please ask for repair

The washer automatically

removes this problem; if the

problem remains, please

ask for repair

Shut down the washer and

remove the problem; if the

problem remains, please ask for

repair

Shut down the washer and

remove the problem. Check

whether the water tap is turned on,

whether the water pressure is too

low, whether water supply cut-off

occurs; Check whether the

water inlet valve is clogged

(please clean it); if the problem

remains, please ask for repair

Clean the draining pump filter

and check whether the drain

pipe is clogged; if the problem

remains, please ask for repair

The washer is in automatic

weighing state

The remaining washing time is

one hour and sixteen minutes

The spinning speed is set

at 800 rpm

The whole program ends

Abnormal door locking or

unclosed door

Drainage fault

Temperature sensor fault

Heating fault

Abnormal water inflow

The motor speed is higher

or lower than the pre-set

speed

The motor stops running

The water level exceeds

alarm level

Water level sensor fault

Uneven clothes distribution

while spinning

Poor washing effect

Check whether the type and dosage of

detergent are suitable

Check whether the selected program is

correct

Check whether the clothes weight

exceeds the washer’s rated washing

capacity

Check whether the washer is washing

a single piece of clothing, e.g. woolen

sweater. If so, it is normal

The spinning effect varies with the

type of clothes

Check whether it is for eccentric

protection with few clothes

It is normal that electronic

components are slightly hot

The clothes distribution becomes

imbalanced during washing

Poor water feeding/drainage

conditions result in a longer time

Check whether the drain pipe is bent,

clogged or frozen

Check whether the drain pipe orifice is

100cm higher than the floor

Check whether the filter is clogged

Check whether all the fixing bolts for

transport are removed

Check whether the washer is level (the

washer can be leveled by adjusting the feet)

Check whether the clothes intertwist

Check whether the washer collides with

other objects

Check whether there are foreign bodies in

the washer

Check whether sudden power failure

or water supply cut-off occurs

Check whether the “Start/Pause”

button is pressed

The washer’s program is set with

water discharge time and the

spinning starts after a period of time

Check whether the clothes intertwist

Check whether too much washing

powder was added

Forceless washing

Stop operation

during washing

No spinning

Excessively long

spinning time

Loud noise when spinning

Vibration and

displacement

The clothes are not

spun dry after finishing

the “Spin” program

No water discharge or

slow water discharge

The control panel is

partially hot

The washing does not

end after the preset

delay time

Check whether the washer inclines or shakes

Check whether there are foreign bodies such

as coins and zippers in the washer

Check whether the noise is from the buttons

and zippers of washing

Check whether the noise is from the draining

pump or motor in normal operation

The washer does

not operate

Buttons cannot be

operated

Water leakage occurs

at the water tap

No water inflow or

slow water inflow

Water feeding and water

drainage occurs at the

same time

Abnormal noise

Press the “Temp.” button to

select heating temperature

(--, 30, 40, 50, 60, 90). The

maximum allowable

heating temperature varies

with programs.

“ － ” in the temperature

display area indicates

non-heated washing.

The variable frequency series is set with the “Auto” function. In this mode, press the “Power” button, the washer will turn on and the door will

automatically open; put the clothes to be washed into the washer and close the door, the display screen will display “ ”; press the

“Start/Pause” button, the washer will automatically weigh the clothes and select the optimal washing program, achieving water, electricity

and time saving.

(1) In manual mode, it is recommended that “L-4” or “L-A” be selected for washing many clothes (more than a half drum) and “L-1”, “L-2” or

“L-3” be selected for washing fewer clothes (not more than a half drum).

(2) The “Auto” function is only available for the “Prewash”, “Cotton”, “Synthetic”, and “Wash” programs. For other programs, press this button

to manually adjust the clothes weight level (the level adjustment is not available for the “Wool” program).

If you do not want the washer to weigh the clothes automatically, press the “Auto” button to switch to manual selection of

clothes weight level (the operation is the same as that of non-variable frequency series).

6. Control Panel and Program Description

Press the “Speed”

button to select

spinning speed.

The maximum

allowable spinning

speed varies with

programs.

“Speed” selection

It displays delay time,

remaining washing time,

times of extra rinse,

spinning time, set

temperature, set speed,

clothes weight level, child

lock state, door lock state

and alarm message, etc.

Display screen “Temperature” selection “Auto”/“Clothes weight level selection” button Program knob

Note:

Select the desired

program by turning

this knob.

After turning on the

washer, it

automatically

selects the

program of last

washing.

Press the “Delay” button, its indicator will light up, indicating

this function is selected. The delay time (0.5-24h) increases by

30 minutes each press of “Delay” button. The time will change

continuously if you press and hold this button until you release

it.

The delay time is the end time of washing. For example, 6:00

means the washing ends after 6 hours (the delay time must be

longer than the program’s running time).

This function is not available for the “Spin” program.

“Delay” button

Press the “Extra rinse” button to increase the times of rinse

(at most three times) between the “Rinse” and “Soften”

programs.

When the indicator of “Extra rinse” lights up, it means this

function is selected. Each press of the “Extra rinse” button

increases one time of rinse. P--1~P--3 shows on the

display screen. Press this button again, this function will be

cancelled and the indicator will go out.

This function is not available for the “Wash” and “Spin”

programs.

“Extra rinse” button

Press the “IStrong” button to select or

cancel the function of intensive washing.

This function is to increase washing time,

times of rinse and spinning time of the

main wash stage of the selected program.

When the “Strong” indicator lights up, it

means this function is selected. This

function is not available for the “Rinse” and

“Spin” programs.

“Strong” button

Press the “Start/Pause” button, the

washer will start or pause. When the

washer pauses, the indicator will

flash.

When the washer is turned on and

the “Start/Pause” button is not

pressed, you may open the door by

pressing and holding this button for 2

seconds.

“Start/Pause” button

n o t t u b ” r e w o P “

Press the “Power” button to

switch on the washer.

Press this button again and

hold it for 2 seconds to

switch it off.

After switching on the

washer, if any button is not

pressed within 5 minutes, it

will automatically turn off.

Programs Guide

Prewash

Cotton

Synthetic

Wool

Underwear

Sport Wash

Quick

Wash

Rinse

Spin

For washing relatively dirty

cotton fabrics

For washing cotton fabrics

For washing chemical fiber

fabrics

For washing wool fabrics

For washing cotton underwear

For washing sport wear

or children’s clothes

For washing slightly dirty cotton

and chemical fiber fabrics

For washing the clothes only

For rinsing the clothes only

For spinning the clothes only

7. Display Screen 8. Other functions

Numerical display area

Child lock icon

Door lock icon

1. Numerical display area: the delay time, remaining time, times of extra rinse and alarm message, etc. display in this area.

When the washer is in operation, remaining time displays in this area; if you turn on the washer after the selected program

ends, the program time of last washing will display in this area, e.g. 1:28; when the “Delay” function is selected, the delay time

will display in this area, e.g. 6:00; when the “Extra rinse” function is selected, the additional times of extra rinse will display in

this area, e.g. P--1; when the program running is abnormal, alarm message will display in this area, e.g. Err3.

2. Child lock icon: simultaneously press the “Delay” and “Start/Pause” buttons and hold them for 3 seconds, the child lock

function will be activated to avoid changing the selected program by inadvertent touch of buttons; simultaneously press the two

buttons and hold them for 3 seconds again, this function will be cancelled.

3. Door lock icon: this icon will light up when the door is closed and will not show when the door is opened.

Note:

The time shown on the display screen is only for reference and may be slightly different from actual

time due to water temperature and water pressure, etc.

The child lock function will be cancelled when the selected program ends, power failure occurs or the

washer is switched off.

Function

Power-down memory

With the power-down memory function, the washer can

memorize the program’s running state in case of power

failure or loose plug during washing and continue the

formerly selected program after the power supply resumes.

Eccentric protection

When spinning, if the clothes are not evenly distributed, the washer will fluff out

and redistribute the clothes and continue spinning after the clothes distribution

becomes even. If the clothes distribution does not become even within the

specified time, the washer will not spin to avoid abnormal vibration. In this case,

please check the clothes for intertwist and rearrange them, then select “Spin”

program to spin the clothes. When there are few clothes, the washer may not spin

due to eccentric protection. In this case, you can put more clothes into the washer

and make them evenly distributed, then continue spinning. In addition, it is normal

that the program time will prolong because the washer rearranges and fluffs out

the clothes.

Silencing function

Select the “Spin” program, simultaneously press the “Delay” and “Extra rinse”

buttons and hold them for 3 seconds, the beep of all the programs (excluding the

alarm sound) will be silenced and the display screen will show “ ”.

Simultaneously press the two buttons and hold them for 3 seconds again, the

beep of all the programs will resume and the display screen will show “ ”.

Cancel or reselect a program during washing

(1) To cancel the running program, just turn off the washer;

to reselect a program, turn it on again.

(2) To select any additional function when a program is

running, just press the “Start/Pause” button, then select your

desired additional function and finally press the

“Start/Pause” again.

The above operations should be made when the child lock is

not activated.

The method (2) is only available for several function buttons.

Note:

9. Fault Clearance

The following phenomena are not necessarily faults of the washer. Please check against the following table before calling for repair.

If any fault actually exists, please contact our After-sales Service Department and do not repair by yourself. Please pull out the power plug before check.

State Phenomenon Solution State Phenomenon Solution Displayed code Code meaning Solution Displayed code Code meaning Solution

e r o f e B

n o i t a r e p o

h s a w n e h W

There is a little water in

the drain pipe and

washer when using the

washer for the first time

It is normal; the water is the remaining

water of factory inspection

Check whether the “Child lock” function is

selected

After starting, to select other programs,

please press the “Start/Pause” button and

then operate

Check whether the height of drain pipe

orifice is within the range of 80cm~100cm

Check whether the drain pipe orifice is

immersed in the water

Check whether the water tap is in proper shape

Check whether the water inlet pipe joint is

installed in place

Check whether the water tap is damaged

Check whether the water tap is turned on and

whether water supply cut-off occurs

Check whether the water inlet valve is clogged (if

necessary, clean the valve)

Check whether the water tap and water inlet pipe

are frozen

Check whether the “Delay” program is selected

Check whether the “Start/Pause” button is pressed

Check whether the water inlet pipe is bent

Check whether the water pressure is too low

Check whether power failure or abnormal

power supply occurs

Check whether the power plug is firmly

inserted into the socket

Check whether the fuse of power supply or the

current breaker is in good condition

Check whether the “Power” switch is turned on

Check whether the water tap is turned on

Check whether the “Delay” function is selected

Check whether the “Start/Pause” button is

pressed

n i p s n e h W h s a w n e h W

n e h W

e g r a h c s i d

r e t a w

r e h t O

Communication fault

Being inconsistent with the

conditions for door opening,

it is not allowed to unlock

the door

and alarms are limited to the variable frequency series.

is limited to the non-variable frequency series.

It is normal that the washer discharges water when or occurs.

Please ask for repair

Note:

Warm tips

To add clothes during washing or to take out clothes

after extended power failure, make sure that the

water level in the drum is properly below the lower

edge of sight glass, the water temperature is below

the drain pipe from its holder and put it down until no

water is drained from the drain pipe, afterwards put

back the drain pipe. Open the filter door at the bottom

of washer, and you will see a pull wire. Take out the

pull wire and gently pull it downwards until you hear a

low sound, the door will open, now you can add or

take out the clothes. Afterwards, reset the pull wire

and filter door.

Pull wire

Note:

Never perform the above operations when the washer is running.

The washer contains recyclable materials. Please properly dispose of them to protect

the environment.

Adding a proper amount of softener may make the clothes soft, eliminate sticking arising

from static electricity and make the clothes easier to be ironed. Excessive soften may

damage synthetic fiber. Please refer to its instructions for correct dosage of softener.

10.Cleaning/Maintenance

Fig. 1

Fig. 2

Fig. 3 Fig. 4 Fig. 5

Filter

Waste pipe

Waste pipe plug

Water container

Please pull out the power plug from the socket before

cleaning and maintenance.

Filter cleaning (once a month as recommended)

(1) After draining the water in the washer, open the filter door by pressing it

down with a flat head screwdriver or a similar tool through the square hole

above the filter door (as shown in Fig. 1).

(2) Hold the plastic pipe plug to pull out the waste pipe, prepare a water

container, remove the plastic plug of waste pipe to drain the remaining

water into the container (as shown in Fig. 2), replace the plastic plug onto

the waste pipe, and finally clamp the waste pipe in original position.

(3) Anticlockwise screw out the filter. It is normal that a little water flows out

at this time (as shown in Fig. 3).

(4) Rinse with clean water (as shown in Fig. 4).

(5) Insert the filter after aligning its convex with the groove of draining pipe,

then clockwise tighten it (as shown in Fig. 5), and finally close the filter door.

Note:

The filter must be

tightened to avoid

water leakage.

Cleaning of a distributor box

To clean a distributor box, pull it out, gently

press it down and continue to pull it out (as

shown in the figure on the right), remove it,

rinse it with water and reinstall it in place.

Cleaning of the filter screen of water inlet valve

Frequently clean the water inlet pipe joint and

the filter screen of water inlet valve to prevent

them from being clogged by impurities (as

shown in the figure on the right)

Please clean the filter screen of water

inlet valve as shown in the figures below.

Take out the filter screen W ash the filter screen

Reinstall the filter

screen in place

water inlet

valve joint

Please ask for repair

Press and hold 2seconds

to set door unlocked

Pause

Prewash

Synthetic

Cotton

Wool

Unde wear r

Sport Wash

Quick

Wash

inse

HW55-B12866NZP

Haier HW55-B12866NZP User manual

Brand: Haier

Model: HW55-B12866NZP

Category: Washing machines

Type: User manual

Download PDF

report

Haier HW55-B12866NZP User manual

Haier HW55-B12866NZP User manual

Related papers

Other documents