Agri-Fab 45-0301 Operating instructions

Agri-Fab
Brand
Agri-Fab
Model
45-0301
Category
Spreader
Type
Operating instructions
• Safety
• Assembly
• Operation
• Maintenance
• Parts
CAUTION:
ReadRulesfor
SafeOperation
andInstructions
Carefully
PRINTEDINU.S.A. FORMNO.42530(12/8/15)
175 LB. POLY PRO
SPIKER/SPREADER
OWNERS
MANUAL
Model No.
45-03012
the fastest way to purchase parts
www.speedepart.com
2
RULES FOR SAFE OPERATIONS
• Readthisowner'smanualbeforeattemptingto
assembleoroperatethespiker/spreader.
• Readthetowingvehicleowner'smanualandknow
howtooperatethetractorbeforeusingthespiker/
spreader.
• Donotallowanyonetorideonorsitonthespiker/
spreader.
• Neverallowchildrentooperatethetractororspiker/
spreader.
• Donotallowadultstooperatethetractororspiker/
spreaderwithoutproperinstructions.
• Readthechemicallabelforinstructionsandcautions
forhandlingandapplyingchemicals.
Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.
Exercisecautionatalltimes,whenusingpowerequipment.
• Weareyeandhandprotectionwhenhandlingand
usinglawnchemicals.
• Alwaysbeginwiththetransmissioninrst(low)gear
andgraduallyincreasespeedasconditionspermit.
Maximumtowingspeed-6M.P.H.
• Donotdrivetooclosetoacreekorditchandbealert
forholesandotherhazardswhichcouldcauseyouto
losecontrolofthetractorandspiker/spreader.
• Beforeoperatingthevehicleonanygrade(hill)refer
tothesafetyrulesinthevehicleowner'smanual
concerningsafeoperationonslopes.Stay off steep
slopes!
• Followmaintenanceandlubricationinstructionsas
outlinedinthismanual.
Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans—Attention!!
Become alert!! Yoursafetyisinvolved.
3
CARTON CONTENTS
1. HopperAssembly
2. ChainCover
3. TransportHandle
4. HopperBrace
5. FlowControlGauge
6. FlowControlArm
7. FlowControlRod
8. TongueBraces(2)
9. Tongue
10.HitchBracket
11. LiftTubeAssembly
12.Axle
13.DriveDisk(2)
14.SpikeDisk(10)
15.CenterBrace(2)
16.Wheels(2)
1
2
4
8
9
7
6
5
10
3
47712
24531
23014
63850
24542
24647
24660
24532
47679
24648
63956
63958
47961
11
13
24332
14
15
16
12
63949
4
REF. PART NO. QTY. DESCRIPTION
A 45100 2 HexBolt,1/2"x4"
B 43001 1 HexBolt,3/8"x1"
C 1509-69 2 HexBolt,1/4"x1-3/4"
D 1509-90 1 HexBolt,1/4"x1-1/4"
E 4 3 01 2  2 HexBolt,1/4"x3/4"
F 4 3 8 6 6  16 HexBolt,1/4"x5/8"
G 4 4 9 5 0  1 CarriageBolt,1/4"x3/4"
H 44326 2 CarriageBolt,5/16"x1"
I 4 8 1 0 6  2 ShoulderBolt
J 4 7 1 8 9  24 NylockNut,1/4"
K 47810 2 NylockNut,5/16"
L H A 2 1 3 6 2  1 NylockNut,3/8"
M 43082 2 HexLockNut,3/8"
N 4 3 0 1 9  4 HexJamNut,1/2"
O R 1 9 2 1 2 0 1 6  12 Washer,5/8"
P R 1 9 1 7 1 6 1 6  4 Washer,1/2"
Q 4 3 0 8 8  10 FlatWasher,1/4"
REF. PART NO. QTY. DESCRIPTION
R 1 5 4 3 - 6 9  3 NylonWasher
S 4 3 3 5 3  2 LockWasher,3/8"
T 4 7 6 8 4  1 Chain
U 4 7 6 2 3  1 HitchPin
V 43093 3 CotterPin,1/8"x1-1/2"
W 4 3 3 4 3  1 HairCotterPin
X 4 3 8 4 9  1 PlasticKnob
Y 4 7 7 0 7  1 TransportHandleGrip
Z 4 3 8 4 8  1 ControlArmGrip
AA 74 1- 0 2 4 9  18 FlangedBearing
BB 4 7 7 7 7  2 Spring
CC 4 7 7 11  2 Ferrule
DD 46838 1 Spacer,.5"
EE 47683 6 Spacer,2.9"
FF 47782 1 Spacer,3.2"
HA24629 2 30"PlasticTie(notshown)
B
C
D
E
F
G H
Q
S
T
R
J
K
P
SHOWN FULL SIZE
NOT SHOWN FULL SIZE
X
Y
BB
V
W
A
N
M
I
U
Z
DD
CC
EE
FF
AA
O
L
5
TOOLS REQUIRED FOR ASSEMBLY
(2)7/16"Wrenches
(2)1/2"Wrenches
(2)9/16"Wrenches
(2)3/4"orAdjustableWrenches
(1)Pliers
(1)KnifeorScissors
ASSEMBLY
Spikepointsaresharp.Wearprotectivegloves
andexercisecautionwhenworkingwithhands
nearspikedisks.
FIGURE 1
FIGURE 3
FIGURE 4
FIGURE 2
1. Removethehardwarepackandallindividualpartsfrom
thecartonandlayoutasshownonpages2and3.
2. Pressaangedbearingintoeachspikediskfromthe
atsideofthedisk.Seegure1.
3. Pressaangedbearingintoeachendofbothdrive
disks.Seegure2.
5. Assemblea1/2"spaceranda5/8"washerontothe
axle.Seegure4.
4. Pressaangedbearingintobothcenterbracesfrom
theatsideofeachbrace.Seegure3.
5/8" WASHER
1/2" LONG SPACER
FLANGED BEARING
CENTER BRACE
FLANGED BEARINGFLANGED BEARING
DRIVE DISK
FLANGED BEARINGSPIKE DISK
6
FIGURE 6
FIGURE 7
8. Assembletwospikedisksanda2.9"spacerontothe
axle.Theatsideofthedisksshouldfaceawayfrom
thespacer.Seegure7.
9. Assembletwo5/8"washersandaspringontothe
axle.Seegure7.
IMPORTANT:Whenassemblingpartsontotheaxle,be
surethatthespikedisksarefacinginthedirectionshown
ineachassemblydrawing.
7. Assemblethree5/8"washersandthetwodrivedisks
(facingasshown)ontotheaxle.Seegure6.
FIGURE 5
6. Assembletheaxlethroughtheendofthespreader
framethatcontainsapre-assembledsprocket.See
gure5.
10.Assembletwospikedisksanda2.9"spacerontothe
axle.Theatsideofthedisksshouldfaceawayfrom
thespacer.Seegure8.
FIGURE 8
SPIKE DISKS (2)
2.9" SPACER
SPIKE DISKS (2)
2.9" SPACER
5/8" WASHERS (2)
SPRING
5/8" WASHERS (3)
DRIVE DISKS
7
12.Assembletwospikedisksanda2.9"spacerontothe
axle.Theatsideofthedisksshouldfaceawayfrom
thespacer.Seegure10.
13.Assembletwo5/8"washersandaspringontothe
axle.Seegure10.
FIGURE 10
11. Assembletwo5/8"washers,thetwocenterbraces
andthe3.2"spacerontotheaxle.Theatsideofthe
bracesshouldfaceawayfromthespacer.Seegure9.
FIGURE 9
FIGURE 11
14.Assembletwospikedisksanda2.9"spacerontothe
axle.Theatsideofthedisksshouldfaceawayfrom
thespacer.Seegure11.
30" PLASTIC TIES
15.Assemble30"plastictiesaroundtheeachsetof
spikedisksthatsurroundthesprings.Looptheties
aroundoppositesidesofeachspikedisk.Tightenthe
ties,compressingthespringssothatthereisroomto
assembletherestofthepartsontotheaxle,andto
inserttheaxlethroughtheendofthespreaderframe.
Seegure12.
FIGURE 12
5/8" WASHERS (2)
CENTER BRACES (2)
3.2" SPACER
SPIKE DISKS (2)
2.9" SPACER
5/8" WASHERS (2)
SPRING
2.9" SPACER
SPIKE DISKS (2)
8
16.Assemblea2.9"spacerontotheaxle.Seegure13.
17. Assembletwospikedisks,a2.9"spaceranda5/8"
washerontotheaxle.Theatsideofthedisksshould
faceawayfromthespacer.Seegure13.
FIGURE 13
23.Assemblethechainaroundthesprockets,andthen
fastentheendsofthechaintogetherusingthe
connectinglink.Seegure16.
FIGURE 16
FIGURE 14
CHAIN
CONNECTING LINK
18.Slidetheaxleonthroughtheendofthespreader
frame.Youmayneedtostraightenthespikedisks
oneithersideofthespringstoallowtheaxletoslide
freely.Seegure14.
19.Assemblea5/8"washerontotheendoftheaxle.See
gure14.
20.Assembleacotterpinintotheendoftheaxleand
thenspreadtheendsofthecotterpin.Seegure14.
HINT:Youmayneedtopushagainsttheendplateto
makeroomontheaxletoinstallthecotterpin.Tryturning
thespreaderonendtogetbetterleverageforpushing.
FIGURE 17
24.Attachthelifttubeassemblytothespreaderusingthe
twoshoulderboltsandtwo3/8"hexlocknuts.See
gure17.
SPIKE DISKS (2)
5/8" WASHER
2.9" SPACER
2.9" SPACER
21. Assembletwocotterpinsintothedrivedisks.Spread
theendsofthecotterpins.Seegure15.
22.Cuttheplastictiesandremovethemfromthedrive
disks.Seegure15.
COTTER PIN
PLASTIC TIES
FIGURE 15
SHOULDER BOLT
3/8" HEX
LOCK NUT
COTTER PIN
5/8" WASHER
9
FIGURE 19
1/4" NYLOCK NUT
1/4" NYLOCK NUT
1/4" x 5/8"
HEX BOLT
1/4" FLAT
WASHER
1/4" x 1-3/4"
HEX BOLT
CENTER BRACE
26.Attachthetonguetotheframeassemblytubeusing
two1/4"x1-3/4"hexbolts,four1/4"atwashersand
two1/4"hexnuts.Do not tighten yet. Seegure19.
27. Attachthetonguetothetwocenterbracesusing
four1/4"x5/8"hexboltsand1/4"hexnuts.Do not
tighten yet. Seegure19.
28.Assembletheplasticgripontotheendoftheow
controlarm. Seegure20.
29.Inserttheowcontrolarmthroughtheslotinthe
hopperbrace.Placeanylonwasheroneachsideof
thearmandattachittothebrace'sweldedbracket
usinga1/4"x1-1/4"hexbolt,a1/4"atwasherand
two1/4"hexlocknuts.Tightenthersthexlocknut
untilthereisnoticeableresistancewhenmovingthe
owcontrolarm,thentightenthesecondhexlock
nut. Seegure20.
30.Placetheowcontrolrodthroughtheholeattheend
oftheowcontrolarm.Assemblethetwoferrulesonto
thethreadedendsoftherodsothatapproximately10
threads(1/2")oftherodextendsthroughtheferrules.
Seegure20.
FIGURE 20
1/4" NYLOCK NUT
1/4" x 5/8"
HEX BOLT
TONGUE
FRAME ASSEMBLY TUBE
25 Assembletheendofthetonguetothehopperusing
two1/4"x5/8"hexboltsand1/4"hexnuts.Theholes
arelocatedjustbelowtheframeassemblytube.Do not
tighten yet. Seegure18.
FIGURE 18
NYLON
WASHER
1/4" NYLOCK
NUTS
1/4" FLAT
WASHER
1/4" x 1-1/4"
HEX BOLT
PLASTIC
GRIP
FERRULE
FLOW
CONTROL
ROD
FLOW
CONTROL
ARM
HOPPER
BRACE
1/2"
10
FIGURE 23
PLASTIC
KNOB
NYLON
WASHER
1/4" x 3/4"
CARRIAGE BOLT
FLOW
CONTROL
GAUGE
37. Assembletheowcontrolgaugetothehopperbrace
usingthe1/4"x3/4"carriagebolt,anylonwasherand
theplasticknob.Seegure23.
33.Insertatonguebracethroughtheslotintheendplate.
Fastenthefrontholeofthetonguebracetotheend
plateusinga1/4"x5/8"hexboltand1/4"hexnut.
Fortherearholeusea1/4"x3/4"hexbolt,1/4"at
washerand1/4"hexnut,withtheboltandwasher
assembledfrominsidethepolyhopper.Seegure22.
Do not tighten yet.
34.Fastentheotherendofthetonguebracetotheside
ofthetongueusingtwo1/4"x5/8"hexboltsand1/4"
hexnuts.Do not tighten yet.Seegure22.
35.Repeatsteps10and11forthesecondtonguebrace.
36.Tightenallboltsandnutsassembledsofar.
1/4" x 5/8"
HEX BOLT
1/4" NYLOCK
NUT
1/4" x 5/8"
HEX BOLT
1/4" NYLOCK NUT
1/4" x 3/4"
HEX BOLT
1/4" FLAT
WASHER
WHEEL REMOVED
FOR ACCESS
FIGURE 22
FIGURE 21
3/8" HEX
NYLOCK NUT
1/4" x 5/8"
HEX BOLT
3/8" x 1"
HEX BOLT
1/4" FLAT
WASHER
(ONE ONLY)
1/4" HEX NUT
HOPPER
BRACE
HITCH
BRACKET
31. Attachthehopperbracetothehopperusingtwo1/4"
x5/8"hexbolts,one1/4"atwasherandtwo1/4"hex
nuts.Do not tighten yet.Seegure21.
32.Placetheendofthehitchbracketwithtwoholes
downthroughtheslotinthetongue.Attachthehopper
bracetothetopofthetongueandthehitchbracket
tothebottomusingone3/8"x1"hexbolt,3/8"lock
washerand3/8"hexlocknut.Do not tighten yet.
Seegure21.
11
41. Attachthetransporthandletotheliftassemblyarm
usingtwo5/16"x1"carriageboltsandtwo5/16"
nylocknuts.Seegure25.
42.Assemblethehandlegriptothetransporthandle.See
gure25.
(2) 5/16" NYLOCK NUTS
TRANSPORT HANDLE
HANDLE GRIP
(2) 5/16" x 1"
CARRIAGE BOLTS
FIGURE 26
FIGURE 25
43.Assemblethechaincovertotheframeassembly
usingtwo1/4"x5/8"hexbolts,1/4"atwashersand
1/4"hexnutsasshowngure26.
44.Installthehitchpinandthe1/8"haircotterpininthe
spreaderhitchbracketandtongue.Seegure26.
39.Tocheckforcorrectopeningofhopperowplates:
a. Settheowcontrolgaugeatthehighestsetting.
b. Movetheowcontrolarmawayfromthehopper
untilitrestsagainstthegauge.Theslotsinthe
bottomofthehoppershouldnowbecompletely
open.Theedgeoftheowplatesshouldbejust
clearoftheendsalltheslots.
c. Iftheowplatesarenotstraightwiththeslots,
screwoneferruleupordownononesideofthe
controlrod.
d. Iftheowplatesopentofarornotfarenough,
screwbothferrulesequallyupordownonthe
controlrod.
d. Movetheowcontrolarmtowardthehopperto
theoffposition.Verifythattheslotsinthebottom
ofthehopperarecompletelycoveredbytheow
plates.
e. Tightenthelocknutsandthenloosen1/4turn.
40.Tocheckforpropertensiononthehopperowplates:
a. Settheowcontrolgaugeatamidrangesetting.
b. Movetheowcontrolarmagainstthegauge.
c. Pressrmlyagainstthefrontoftheowplates
atthebottomofthehopper.Theowcontrolarm
shouldnotmove.
d. Ifthearmmoves,tightenthehexlocknutsonthe
owcontrolarmuntilmovementisprevented.
38.Checkthatbothferrulesareadjustedsothat
approximatelytenthreads(1/2")ofthecontrolrodis
exposed.Insertbothferrulesintothebracketswhich
arerivetedtothefrontoftheowplates.Assemblea
1/4"hexlocknutontoeachferrule,makingonlynger
tightatthistime.Seegure24.
1/4" NYLOCK NUT
BRACKET
FERRULE
FIGURE 24
1/4" NYLOCK NUT
1/4" x 5/8"
HEX BOLT
1/4" FLAT
WASHER
CHAIN COVER
1/8" HAIR
COTTER PIN
3/8" HITCH PIN
12
FIGURE 27
APPLICATION TIPS
1. Tohelppreventcompactingandcloggingwhenusing
granularmaterial,avoidunnecessarytowingwhile
hopperislled.
2. Reducetheowsettingforspeedsslowerthan
3M.P.H.andincreasethesettingforhigherspeeds.
3. Toavoidmissesorstriping,overlapthepreviouspass
slightly.Spreadwidthisapproximately40".
4. Foreasiestapplication,rstapplymaterialacross
bothendsofthearea.Twoorthreepassesoneach
endaresufficient.Thenapplymaterialbackandforth
asshown.Usetheendareasforturningaround,
shuttingoffthespreaderasyouentertheendareas
andturningthespreaderonagainasyourleavethe
endareasforyournextpass.Seegure28.
5. Iflawnisoddshaped,spreadaborderaroundthe
edgesandthenspreadbetweentheborder.
6. Becarefulwhenspreadingaroundornamentalplants
becauseweedcontrolchemicalscandamagethese
plants.
PLASTIC
KNOB
FLOW RATE
SETTING (6)
0
1
2
4
6
FLOW CONTROL ARM
ON
OPERATION
HOW TO USE YOUR SPIKER/SPREADER
1. Refertotheinstructionlabelonthematerialpackage
andtotheinstructiondecalonyourspreadertohelp
determinetheproperspreadersettingandapplication
rate.AlsoseetheSettingChartonthispagefor
ageneralrangeofsettingsforcommonlyused
materials.
2. Loosentheknobandadjusttheowcontrolgaugeto
therecommendedsetting.Retightentheknob.See
gure27.
3. Determinetheapproximatesquarefootageofthearea
tobecoveredandestimatetheamountoffertilizeror
seedrequired.
4. Movethespiker/spreadertotheareawhere
applicationistobegin.
5. Makingsuretheowcontrolarmisinthe"OFF"
position,llthehopper,breakingupanylumps.
6. Lowertheaeratorspikestotheoperatingposition.
7. Startthespreaderinmotionandthenpulltheow
controlarmforwardtothe"ON"positionasyoutravel
acrossyourlawn.Therecommendedtowingspeedis
3m.p.h.
8. Donotmakesharpturnswithspikesintheground.
9. Raiseaeratorspikestotransportpositionwhen
crossingoverconcreteorotherhardsurfaces.
10.Donotaerateifthegroundisextremelyhardordry.
Ifgroundistoodry,sprinkleorwaterforonetotwo
hourspriortouse.
11. Donotaerateifthegroundistoowet(muddy).
IMPORTANT:Alwaysmoveowcontrolarmto"OFF"
positiontopreventexcessivereleaseoffertilizerwhen
stopping,turningorllingthespreader.
FIGURE 28
MAINTENANCE
1. Checknutsandboltsfortightnessbeforeeachuse.
2. Alwaysemptyhopperaftereachuse,storingleftover
materialinit'soriginalbag.
3. Washanddrythoroughlyaftereachuse.
4. Applyalightcoatofoilonexposedmetalpartstohelp
preventrust.
5. Atleastonceayear,applyafewdropsofoiltowheels
andtoplasticbearingsinspikedisks,atendsof
aeratorshaftandatendsofhoppershaft.
6. Cleanandoildrivechainonceayear.
Spike points are sharp. Exercise caution
whenworkingwithhandsnearspikedisks.
Flow Rate Setting
MATERIAL TYPE At 3 M.P.H.
SETTING CHART
Fertilizer Granular/Pelleted 0-1 / 0-2
GrassSeed Fine/Coarse 5-6 / 7-8
3M.P.H.isequivalenttotraveling100feetin23seconds.
13
PARTS FOR 175 LB. POLY "PRO" SPIKER/SPREADER MODEL 45-03012
REF
NO.
PART NO. QTY DESCRIPTION
1 43848 1 PlasticGrip
2 24660 1 FlowControlArm
3 47712 1 FlowControlRod
4 47711 2 Ferrule
5 1543-69 3 NylonWasher
6 43088 8 Washer,1/4"
7 1509-90 1 Bolt,Hex1/4-20x1-1/4"Lg.
8 47189 22 Nut,Nylock1/4-20Thd.
9 63850 1 BraceAssembly,Hopper
10 24542 1 FlowControlGauge
11 43849 1 PlasticKnob,1/4-20Thd.
12 44950 1 Bolt,Carriage1/4-20x3/4"Lg.
13 43001 1 Bolt,Hex3/8-16x1"Lg.
REF
NO.
PART NO. QTY DESCRIPTION
14 47623 1 Pin,Hitch3/8"FlatHd.
15 23014 1 HitchBracket
16 24531 1 Tongue
17 43343 1 Pin,HairCotter#4(1/8")
18 HA21362 1 Nut,Nylock3/8-16Thd.
19 44326 2 Bolt,Carriage5/16-18x1"
20 1509-69 2 Bolt,Hex1/4-20x1-3/4"
21 43866 14 Bolt,Hex1/4-20x5/8"
22 43012 2 Bolt,Hex1/4-20x3/4"
23 24532 2 TongueBrace
24 47810 2 Nut,Nylock5/16-18
25 47707 1 HandleGrip
26 24647 1 TransportHandleBar
14
1
4
5
7
16
2
3
5
5
6
8
16
16
17
18
19
21
D
D
14
15
15
13
4
6
B
B
6
19
16
7
4
39
4
6
30
C
C
24
12
20
20
45
45
27
34
27
34
41
42
23
26
40
40
38
29
32
32
45
34
34
34
34
34
27
34
34
27
27
27
27
27
27
27
27
27
27
27
27
27
27
33
33
33
33
33
33
31
31
35
36
36
37
37
37
37
37
37
37
37
37
34
34
34
22
9
10
28
11
11
5
44
45
37
A
25
47
46
42
A
PARTS FOR 175 LB. POLY "PRO" SPIKER/SPREADER MODEL 45-03012
15
PARTS FOR 175 LB. POLY "PRO" SPIKER/SPREADER MODEL 45-03012
REF
NO.
PART NO. QTY DESCRIPTION
1 47451 1 Hopper
2 24536 1 HopperCenterPlate(Small)
3 24535 1 HopperCenterPlate(Large)
4 43088 7 Washer,1/4"
5 43866 4 Bolt,Hex1/4-20x5/8"
6 46978 6 Nut,Hex(SIMS)1/4-20Thd.
7 47615 2 Bearing,Flange
8 47484 1 Bearing,HexFlange
9 24538 1 Bracket,FeedPlate(RH)
10 24539 1 Bracket,FeedPlate(LH)
11 63949 1 Axlew/Sprocket,5/8"
12 728-3001 10 PopRivet
13 47459 1 Skirt,48"
14 47508 1 SkirtRetainer
15 24537 2 FlowPlate
16 43009 12 Washer
17 47259 4 AgitatorBlade
18 47978 16 Screw,#8-32x1/4"Lg.
19 63948 1 Axlew/Sprocket,3/4"
20 46838 2 Spacer,.76"x1.0"x0.50"
21 47458 2 Spacer,1.25"ODx.330"Lg.
22 65790 1 HopperFrameAssembly
23 47961 2 Wheel
24 1509-69 2 Bolt,Hex1/4-20x1-3/4"
REF
NO.
PART NO. QTY DESCRIPTION
25 26007 2 StepBushing(Special)
26 63958 1 LiftTubeAssembly
27 741-0249 18 Bearing,Flanged0.63"I.D.
28 47684 1 Chain
29 48106 2 Bolt,Shoulder3/8-16x5/8"
30 43082 2 Nut,HexLock3/8-16
31 24648 2 CenterBrace
32 47777 2 CompressionSpring
33 47683 6 Spacer,.75"x1.0"x2.98"
34 R19212016 12 Washer,21/32x1-1/4x16ga.
35 47782 1 Spacer,1.0"IDx3.25"
36 63956 2 DriveDiskAssembly
37 24332 10 SpikeDisk(7")
38 45100 2 Bolt,Hex1/2-13x4"
39 47189 2 Nut,Nylock1/4-20
40 R19171616 4 Washer,17/32"x1"x16ga.
41 43353 2 LockWasher,1/2"
42 43019 4 Nut,HexJam1/2-13
43 HA24629 2 Tie,Plastic30"(notshown)
44 47679 1 ChainCover
45 43093 4 CotterPin,1/8"x1-1/2"
46 48840 6 Screw,1/4-20x1/2"
47 26005 2 AxleRetainerBracket
42530 1 OwnersManual
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab,Inc.
809SouthHamilton
Sullivan,IL.61951
217-728-8388
www.agri-fab.com
the fastest way to purchase parts
www.speedepart.com
Thisdocument(ormanual)isprotectedundertheU.S.CopyrightLawsandthecopyrightlawsofforeigncountries,
pursuanttotheUniversalCopyrightConventionandtheBerneconvention.Nopartofthisdocumentmaybereproduced
ortransmittedinanyformorbyanmeans,electronicormechanical,includingphotocopyingorrecording,orbyany
informationstorageorretrievalsystem,withouttheexpresswrittenpermissionofAgri-Fab,Inc.Unauthorizedusesand/or
reproductionsofthismanualwillsubjectsuchunauthorizedusertocivilandcriminalpenaltiesasprovidedbytheUnited
StatesCopyrightLaws.
©2000Agri-Fab,Inc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Agri-Fab 45-0301 Operating instructions

Agri-Fab
Brand
Agri-Fab
Model
45-0301
Category
Spreader
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents