Metra 87-99-3052 Operating instructions

Category
Car kits
Type
Operating instructions

Metra 87-99-3052 allows you to install an aftermarket radio in your Chevrolet/GMC Truck or SUV made between 1973 and 1991. It offers two radio provision options: 2-shaft or DIN. The kit includes a faceplate, DIN radio housing, and all necessary hardware for a secure installation. Additionally, detailed instructions with illustrations are provided to guide you through the disassembly and reassembly process.

Metra 87-99-3052 allows you to install an aftermarket radio in your Chevrolet/GMC Truck or SUV made between 1973 and 1991. It offers two radio provision options: 2-shaft or DIN. The kit includes a faceplate, DIN radio housing, and all necessary hardware for a secure installation. Additionally, detailed instructions with illustrations are provided to guide you through the disassembly and reassembly process.

CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 10/8/18 INST87-99-3052
INSTALLATION INSTRUCTIONS
87-99-3052
KIT FEATURES
2-shaft radio provision
DIN radio provision
KIT COMPONENTS
• A) Faceplate • B) DIN radio housing
TOOLS REQUIRED
• Phillips screwdriver • Metal & plastic cutting tool
• Scribe tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly
–2-shaft radio provision ........................................4
–DIN radio provision ..............................................5
A B
Chevrolet / GMC Trucks/SUV’s 1973-1991
APPLICATIONS
Chevrolet
Blazer 1973-1987
C/K Pickup 1973-1987
Kodiak C4500-C8500 1981-1990
Suburban 1973-1987
GMC
C/K Pickup 1973-1987
Jimmy 1978-1987
Kodiak 1981-1989
R/V Pickup 1987-1991
Suburban 1973-1987
1.800.221.0932
|
MetraOnline.com
2
1. Remove (4) Phillips screws securing the lower steering column
panel, then remove the panel.
2. Remove (8) Phillips screws from the perimeter of the dash trim
bezel, then remove the bezel.
3. Remove (3) Phillips screws securing the radio. Remove any
objects behind the radio prohibiting it from being removed. Slide
the radio out, then unplug and remove the radio.
Continue to Kit Assembly
2-Shaft radio provision
1. Reinstall the factory trim bezel in reverse order of
disassembly.
2. Position the
faceplate
against the face of the factory
trim bezel, then slide it to the right until the right edge
of
the
faceplate
meets the lip of the bezel. (Fig. A)
3. Slide the radio through the sub-dash, dash trim
bezel, then the
faceplate
. Secure the radio with the
shaft nuts provided with the radio. (Fig. B)
4. Locate the factory wiring harness and antenna
connector in the dash and complete all necessary
connections to the radio. Metra recommends using
the proper mating adapter from Metra. Test the radio
for proper operation.
5. Reassemble the dash in reverse order of disassembly
to complete the installation.
Fig. A
Fig. B
DASH DISASSEMBLY KIT ASSEMBLY
REV. 10/8/2018 INST87-99-3052
3
Fig. A
Fig. B
Fig. C
Fig. D
Fig. E
KIT ASSEMBLY
DIN radio provision
1. Temporarily secure the
DIN radio housing
to the sub-dash using the factory screws.
(Fig. A)
2. Scribe the sub-dash metal on the inside
of the
DIN radio housing
. (Fig. B)
3. Remove the
DIN radio housing
.
4. Cut the sub-dash along the scribed line.
5. Permanently secure the
DIN radio
housing
to the sub-dash using the factory
screws. (Fig. C)
6. Cut and remove the 2-shaft supports
from the
faceplate
.
7. Reinstall the factory trim bezel in reverse
order of disassembly.
8. Remove the metal DIN sleeve from the
aftermarket radio.
9. Position the
faceplate
against the face of
the factory trim bezel, then slide it to the
right until the right edge of the
faceplate
meets the lip of the bezel. The DIN holes
previously cut should line up. (Fig. D)
10. Slide the sleeve through the radio
opening and secure by bending the metal
locking tabs down, then slide the radio
back into the sleeve until it clicks in.
(Figure E)
11. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra. Test
the radio for proper operation.
12. Reassemble the dash in reverse order of
disassembly to complete the installation.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
IMPORTANT
If you are having difficulties with the installation of this product,
please call our Tech Support line at 1-800-253-TECH. Before
doing so, look over the instructions a second time, and make
sure the installation was performed exactly as the instructions
are stated. Please have the vehicle apart and ready to perform
troubleshooting steps before calling.
Metra. The World’s Best Kits.
®
MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 10/8/18 INST87-99-3052
INSTALLATION INSTRUCTIONS
87-99-3052
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Metra 87-99-3052 Operating instructions

Category
Car kits
Type
Operating instructions

Metra 87-99-3052 allows you to install an aftermarket radio in your Chevrolet/GMC Truck or SUV made between 1973 and 1991. It offers two radio provision options: 2-shaft or DIN. The kit includes a faceplate, DIN radio housing, and all necessary hardware for a secure installation. Additionally, detailed instructions with illustrations are provided to guide you through the disassembly and reassembly process.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI